热门标签
热门文章
- 1数据挖掘与机器学习
- 2非线性规划（1）
- 32022 全球 AI 模型周报_ai 小模型 研报
- 42024 AI智能电话语音通话销售机器人源码
- 5Mask R-CNN论文精读_maskrcnn论文原文
- 6PLC通讯实现-C#访问OpcServer实现读写PLC（九）_opc server
- 7自定义圆形、半圆形ProgressBar_u-circle-progress 半圆
- 8生成和关联公钥解决“Permission denied (publickey). fatal: Could not read from remote repository”问题_rsa public key from server
- 9Quartus搭配Modelsim仿真全流程/Bug解决_quartus仿真
- 10带头循环双向链表专题
当前位置: article > 正文
ZYNQ--PL读写PS端DDR数据
作者：Monodyee | 2024-04-24 10:19:28
赞
踩
ZYNQ--PL读写PS端DDR数据
PL 和PS的高效交互是zynq 7000 soc开发的重中之重，我们常常需要将PL端的大量数
据实时送到PS端处理，或者将PS端处理结果实时送到PL端处理，常规我们会想到使用DMA
的方式来进行，但是各种协议非常麻烦，灵活性也比较差，本节课程讲解如何直接通过AXI总
线来读写PS端ddr的数据，这里面涉及到AXI4协议，vivado的FPGA调试等。
1 ZYNQ 的HP端口使用
zynq 7000 SOC 的HP口是 High-Performance Ports的缩写，如下图所示，一共有4
个HP口，HP口是AXI Slave设备，我们可以通过这4个HP接口实现高带宽的数据交互。
- 在vivado的界面中HP的配置如下图(HP0~HP3)，这里面有使能控制，数据位宽选择，可选择32或64bit的位宽。
2)我们的实验启用HP0配置为64bit位宽，使用的时钟是150Mhz，HP的带宽是150Mhz
- 64bit，对于视频处理，ADC数据采集等应用都有足够的带宽。
- 如下图所示，配置完HP端口以后，zynq会多出一个AXI Slave端口，名称为S_AXI_HP0，
不过这些端口都是AXI3标准的，我们常用的是AXI4协议，这里添加1个AXI Interconnect
IP，用于协议转换（AXI3<->AXI4）
2 PL 端AXI Master
AXI4 相对复杂，但SOC开发者必须掌握，对于zynq的开发者，笔者建议能够在一些已
有的模板代码基础上修改。AXI协议的具体内容可参考Xilinx UG761 AXI Reference Guide。
在这里我们简单了解一下。
AXI4 所采用的是一种READY，VALID握手通信机制，即主从模块进行数据通信前，先根
据操作对各所用到的数据、地址通道进行握手。主要操作包括传输发送者A等到传输接受者B
的READY信号后，A将数据与VALID信号同时发送给B，这是一种典型的握手机制。
AXI 总线分为五个通道：
读地址通道，包含ARVALID, ARADDR, ARREADY信号；
写地址通道，包含AWVALID，AWADDR, AWREADY信号；
读数据通道，包含RVALID, RDATA, RREADY, RRESP信号；
写数据通道，包含WVALID, WDATA，WSTRB, WREADY信号；
写应答通道，包含BVALID, BRESP, BREADY信号；
系统通道，包含：ACLK，ARESETN信号；
其中ACLK为axi总线时钟，ARESETN是axi总线复位信号，低电平有效；读写数据与读
写地址类信号宽度都为32bit；READY与VALID是对应的通道握手信号；WSTRB信号为1的
bit 对应WDATA有效数据字节，WSTRB宽度是32bit/8=4bit；BRESP与RRESP分别为写回
应信号，读回应信号，宽度都为2bit，‘h0代表成功，其他为错误。
读操作顺序为主与从进行读地址通道握手并传输地址内容，然后在读数据通道握手并传输
所读内容以及读取操作的回应，时钟上升沿有效。如图所示：
写操作顺序为主与从进行写地址通道握手并传输地址内容，然后在写数据通道握手并传输
所读内容，最后再写回应通道握手，并传输写回应数据，时钟上升沿有效。如图所示：
在我们不擅长写FPGA的一些代码时我们往往要借鉴别人的代码或者使用IP core。在这里
笔者从github上找到一个AXI master的代码，地址是
https://github.com/aquaxis/IPCORE/tree/master/aq_axi_vdma。这个工程是一个自己写的
VDMA，里面包含了大量可参考的代码。笔者这里主要使用了aq_axi_master.v这个代码用于
AXI master 读写操作。借鉴别人代码有时会节省很多时间，但如果不能理解的去借鉴，出现问
题了很难解决。具体可以参考aq_axi_master.v代码，有部分修改。
module mem_test #( parameter MEM_DATA_BITS = 64, parameter ADDR_BITS = 32 ) ( input rst, /*复位*/ input mem_clk, /*接口时钟*/ output reg rd_burst_req, /*读请求*/ output reg wr_burst_req, /*写请求*/ output reg[9:0] rd_burst_len, /*读数据长度*/ output reg[9:0] wr_burst_len, /*写数据长度*/ output reg[ADDR_BITS - 1:0] rd_burst_addr, /*读首地址*/ output reg[ADDR_BITS - 1:0] wr_burst_addr, /*写首地址*/ input rd_burst_data_valid, /*读出数据有效*/ input wr_burst_data_req, /*写数据信号*/ input[MEM_DATA_BITS - 1:0] rd_burst_data, /*读出的数据*/ output[MEM_DATA_BITS - 1:0] wr_burst_data, /*写入的数据*/ input rd_burst_finish, /*读完成*/ input wr_burst_finish, /*写完成*/ output reg error ); parameter IDLE = 3'd0; parameter MEM_READ = 3'd1; parameter MEM_WRITE = 3'd2; parameter BURST_LEN = 128; (*mark_debug="true"*)reg[2:0] state; (*mark_debug="true"*)reg[7:0] wr_cnt; reg[MEM_DATA_BITS - 1:0] wr_burst_data_reg; assign wr_burst_data = wr_burst_data_reg; (*mark_debug="true"*)reg[7:0] rd_cnt; reg[31:0] write_read_len; //assign error = (state == MEM_READ) && rd_burst_data_valid && (rd_burst_data != {(MEM_DATA_BITS/8){rd_cnt}}); always@(posedge mem_clk or posedge rst) begin if(rst) error <= 1'b0; else if(state == MEM_READ && rd_burst_data_valid && rd_burst_data != {(MEM_DATA_BITS/8){rd_cnt}}) error <= 1'b1; end always@(posedge mem_clk or posedge rst) begin if(rst) begin wr_burst_data_reg <= {MEM_DATA_BITS{1'b0}}; wr_cnt <= 8'd0; end else if(state == MEM_WRITE) begin if(wr_burst_data_req) begin wr_burst_data_reg <= {(MEM_DATA_BITS/8){wr_cnt}}; wr_cnt <= wr_cnt + 8'd1; end else if(wr_burst_finish) wr_cnt <= 8'd0; end end always@(posedge mem_clk or posedge rst) begin if(rst) begin rd_cnt <= 8'd0; end else if(state == MEM_READ) begin if(rd_burst_data_valid) begin rd_cnt <= rd_cnt + 8'd1; end else if(rd_burst_finish) rd_cnt <= 8'd0; end else rd_cnt <= 8'd0; end always@(posedge mem_clk or posedge rst) begin if(rst) begin state <= IDLE; wr_burst_req <= 1'b0; rd_burst_req <= 1'b0; rd_burst_len <= BURST_LEN; wr_burst_len <= BURST_LEN; rd_burst_addr <= 0; wr_burst_addr <= 0; write_read_len <= 32'd0; end else begin case(state) IDLE: begin state <= MEM_WRITE; wr_burst_req <= 1'b1; wr_burst_len <= BURST_LEN; wr_burst_addr <='h2000000; write_read_len <= 32'd0; end MEM_WRITE: begin if(wr_burst_finish) begin state <= MEM_READ; wr_burst_req <= 1'b0; rd_burst_req <= 1'b1; rd_burst_len <= BURST_LEN; rd_burst_addr <= wr_burst_addr; write_read_len <= write_read_len + BURST_LEN; end end MEM_READ: begin if(rd_burst_finish) begin if(write_read_len == 32'h2000000) begin rd_burst_req <= 1'b0; state <= IDLE; end else begin state <= MEM_WRITE; wr_burst_req <= 1'b1; wr_burst_len <= BURST_LEN; rd_burst_req <= 1'b0; wr_burst_addr <= wr_burst_addr + BURST_LEN; end end end default: state <= IDLE; endcase end end endmodule
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
- 81
- 82
- 83
- 84
- 85
- 86
- 87
- 88
- 89
- 90
- 91
- 92
- 93
- 94
- 95
- 96
- 97
- 98
- 99
- 100
- 101
- 102
- 103
- 104
- 105
- 106
- 107
- 108
- 109
- 110
- 111
- 112
- 113
- 114
- 115
- 116
- 117
- 118
- 119
- 120
- 121
- 122
- 123
- 124
- 125
- 126
- 127
- 128
- 129
- 130
- 131
- 132
- 133
- 134
- 135
- 136
- 137
- 138
- 139
- 140
- 141
- 142
- 143
module aq_axi_master( // Reset, Clock input ARESETN, input ACLK, // Master Write Address output [0:0] M_AXI_AWID, output [31:0] M_AXI_AWADDR, output [7:0] M_AXI_AWLEN, // Burst Length: 0-255 output [2:0] M_AXI_AWSIZE, // Burst Size: Fixed 2'b011 output [1:0] M_AXI_AWBURST, // Burst Type: Fixed 2'b01(Incremental Burst) output M_AXI_AWLOCK, // Lock: Fixed 2'b00 output [3:0] M_AXI_AWCACHE, // Cache: Fiex 2'b0011 output [2:0] M_AXI_AWPROT, // Protect: Fixed 2'b000 output [3:0] M_AXI_AWQOS, // QoS: Fixed 2'b0000 output [0:0] M_AXI_AWUSER, // User: Fixed 32'd0 output M_AXI_AWVALID, input M_AXI_AWREADY, // Master Write Data output [63:0] M_AXI_WDATA, output [7:0] M_AXI_WSTRB, output M_AXI_WLAST, output [0:0] M_AXI_WUSER, output M_AXI_WVALID, input M_AXI_WREADY, // Master Write Response input [0:0] M_AXI_BID, input [1:0] M_AXI_BRESP, input [0:0] M_AXI_BUSER, input M_AXI_BVALID, output M_AXI_BREADY, // Master Read Address output [0:0] M_AXI_ARID, output [31:0] M_AXI_ARADDR, output [7:0] M_AXI_ARLEN, output [2:0] M_AXI_ARSIZE, output [1:0] M_AXI_ARBURST, output [1:0] M_AXI_ARLOCK, output [3:0] M_AXI_ARCACHE, output [2:0] M_AXI_ARPROT, output [3:0] M_AXI_ARQOS, output [0:0] M_AXI_ARUSER, output M_AXI_ARVALID, input M_AXI_ARREADY, // Master Read Data input [0:0] M_AXI_RID, input [63:0] M_AXI_RDATA, input [1:0] M_AXI_RRESP, input M_AXI_RLAST, input [0:0] M_AXI_RUSER, input M_AXI_RVALID, output M_AXI_RREADY, // Local Bus input MASTER_RST, input WR_START, input [31:0] WR_ADRS, input [31:0] WR_LEN, output WR_READY, output WR_FIFO_RE, input WR_FIFO_EMPTY, input WR_FIFO_AEMPTY, input [63:0] WR_FIFO_DATA, output WR_DONE, input RD_START, input [31:0] RD_ADRS, input [31:0] RD_LEN, output RD_READY, output RD_FIFO_WE, input RD_FIFO_FULL, input RD_FIFO_AFULL, output [63:0] RD_FIFO_DATA, output RD_DONE, output [31:0] DEBUG ); localparam S_WR_IDLE = 3'd0; localparam S_WA_WAIT = 3'd1; localparam S_WA_START = 3'd2; localparam S_WD_WAIT = 3'd3; localparam S_WD_PROC = 3'd4; localparam S_WR_WAIT = 3'd5; localparam S_WR_DONE = 3'd6; reg [2:0] wr_state; reg [31:0] reg_wr_adrs; reg [31:0] reg_wr_len; reg reg_awvalid, reg_wvalid, reg_w_last; reg [7:0] reg_w_len; reg [7:0] reg_w_stb; reg [1:0] reg_wr_status; reg [3:0] reg_w_count, reg_r_count; reg [7:0] rd_chkdata, wr_chkdata; reg [1:0] resp; reg rd_first_data; reg rd_fifo_enable; reg[31:0] rd_fifo_cnt; assign WR_DONE = (wr_state == S_WR_DONE); assign WR_FIFO_RE = rd_first_data | (reg_wvalid & ~WR_FIFO_EMPTY & M_AXI_WREADY & rd_fifo_enable); //assign WR_FIFO_RE = reg_wvalid & ~WR_FIFO_EMPTY & M_AXI_WREADY; always @(posedge ACLK or negedge ARESETN) begin if(!ARESETN) rd_fifo_cnt <= 32'd0; else if(WR_FIFO_RE) rd_fifo_cnt <= rd_fifo_cnt + 32'd1; else if(wr_state == S_WR_IDLE) rd_fifo_cnt <= 32'd0; end always @(posedge ACLK or negedge ARESETN) begin if(!ARESETN) rd_fifo_enable <= 1'b0; else if(wr_state == S_WR_IDLE && WR_START) rd_fifo_enable <= 1'b1; else if(WR_FIFO_RE && (rd_fifo_cnt == RD_LEN[31:3] - 32'd1) ) rd_fifo_enable <= 1'b0; end // Write State always @(posedge ACLK or negedge ARESETN) begin if(!ARESETN) begin wr_state <= S_WR_IDLE; reg_wr_adrs[31:0] <= 32'd0; reg_wr_len[31:0] <= 32'd0; reg_awvalid <= 1'b0; reg_wvalid <= 1'b0; reg_w_last <= 1'b0; reg_w_len[7:0] <= 8'd0; reg_w_stb[7:0] <= 8'd0; reg_wr_status[1:0] <= 2'd0; reg_w_count[3:0] <= 4'd0; reg_r_count[3:0] <= 4'd0; wr_chkdata <= 8'd0; rd_chkdata <= 8'd0; resp <= 2'd0; rd_first_data <= 1'b0; end else begin if(MASTER_RST) begin wr_state <= S_WR_IDLE; end else begin case(wr_state) S_WR_IDLE: begin if(WR_START) begin wr_state <= S_WA_WAIT; reg_wr_adrs[31:0] <= WR_ADRS[31:0]; reg_wr_len[31:0] <= WR_LEN[31:0] -32'd1; rd_first_data <= 1'b1; end reg_awvalid <= 1'b0; reg_wvalid <= 1'b0; reg_w_last <= 1'b0; reg_w_len[7:0] <= 8'd0; reg_w_stb[7:0] <= 8'd0; reg_wr_status[1:0] <= 2'd0; end S_WA_WAIT: begin if(!WR_FIFO_AEMPTY | (reg_wr_len[31:11] == 21'd0)) begin wr_state <= S_WA_START; end rd_first_data <= 1'b0; end S_WA_START: begin wr_state <= S_WD_WAIT; reg_awvalid <= 1'b1; reg_wr_len[31:11] <= reg_wr_len[31:11] - 21'd1; if(reg_wr_len[31:11] != 21'd0) begin reg_w_len[7:0] <= 8'hFF; reg_w_last <= 1'b0; reg_w_stb[7:0] <= 8'hFF; end else begin reg_w_len[7:0] <= reg_wr_len[10:3]; reg_w_last <= 1'b1; reg_w_stb[7:0] <= 8'hFF; /* case(reg_wr_len[2:0]) begin case 3'd0: reg_w_stb[7:0] <= 8'b0000_0000; case 3'd1: reg_w_stb[7:0] <= 8'b0000_0001; case 3'd2: reg_w_stb[7:0] <= 8'b0000_0011; case 3'd3: reg_w_stb[7:0] <= 8'b0000_0111; case 3'd4: reg_w_stb[7:0] <= 8'b0000_1111; case 3'd5: reg_w_stb[7:0] <= 8'b0001_1111; case 3'd6: reg_w_stb[7:0] <= 8'b0011_1111; case 3'd7: reg_w_stb[7:0] <= 8'b0111_1111; default: reg_w_stb[7:0] <= 8'b1111_1111; endcase */ end end S_WD_WAIT: begin if(M_AXI_AWREADY) begin wr_state <= S_WD_PROC; reg_awvalid <= 1'b0; reg_wvalid <= 1'b1; end end S_WD_PROC: begin if(M_AXI_WREADY & ~WR_FIFO_EMPTY) begin if(reg_w_len[7:0] == 8'd0) begin wr_state <= S_WR_WAIT; reg_wvalid <= 1'b0; reg_w_stb[7:0] <= 8'h00; end else begin reg_w_len[7:0] <= reg_w_len[7:0] -8'd1; end end end S_WR_WAIT: begin if(M_AXI_BVALID) begin reg_wr_status[1:0] <= reg_wr_status[1:0] | M_AXI_BRESP[1:0]; if(reg_w_last) begin wr_state <= S_WR_DONE; end else begin wr_state <= S_WA_WAIT; reg_wr_adrs[31:0] <= reg_wr_adrs[31:0] + 32'd2048; end end end S_WR_DONE: begin wr_state <= S_WR_IDLE; end default: begin wr_state <= S_WR_IDLE; end endcase /* if(WR_FIFO_RE) begin reg_w_count[3:0] <= reg_w_count[3:0] + 4'd1; end if(RD_FIFO_WE)begin reg_r_count[3:0] <= reg_r_count[3:0] + 4'd1; end if(M_AXI_AWREADY & M_AXI_AWVALID) begin wr_chkdata <= 8'hEE; end else if(M_AXI_WSTRB[7] & M_AXI_WVALID) begin wr_chkdata <= WR_FIFO_DATA[63:56]; end if(M_AXI_AWREADY & M_AXI_AWVALID) begin rd_chkdata <= 8'hDD; end else if(M_AXI_WSTRB[7] & M_AXI_WREADY) begin rd_chkdata <= WR_FIFO_DATA[63:56]; end if(M_AXI_BVALID & M_AXI_BREADY) begin resp <= M_AXI_BRESP; end */ end end end assign M_AXI_AWID = 1'b0; assign M_AXI_AWADDR[31:0] = reg_wr_adrs[31:0]; assign M_AXI_AWLEN[7:0] = reg_w_len[7:0]; assign M_AXI_AWSIZE[2:0] = 2'b011; assign M_AXI_AWBURST[1:0] = 2'b01; assign M_AXI_AWLOCK = 1'b0; assign M_AXI_AWCACHE[3:0] = 4'b0011; assign M_AXI_AWPROT[2:0] = 3'b000; assign M_AXI_AWQOS[3:0] = 4'b0000; assign M_AXI_AWUSER[0] = 1'b1; assign M_AXI_AWVALID = reg_awvalid; assign M_AXI_WDATA[63:0] = WR_FIFO_DATA[63:0]; // assign M_AXI_WSTRB[7:0] = (reg_w_len[7:0] == 8'd0)?reg_w_stb[7:0]:8'hFF; // assign M_AXI_WSTRB[7:0] = (wr_state == S_WD_PROC)?8'hFF:8'h00; assign M_AXI_WSTRB[7:0] = (reg_wvalid & ~WR_FIFO_EMPTY)?8'hFF:8'h00; assign M_AXI_WLAST = (reg_w_len[7:0] == 8'd0)?1'b1:1'b0; assign M_AXI_WUSER = 1; assign M_AXI_WVALID = reg_wvalid & ~WR_FIFO_EMPTY; // assign M_AXI_WVALID = (wr_state == S_WD_PROC)?1'b1:1'b0; assign M_AXI_BREADY = M_AXI_BVALID; assign WR_READY = (wr_state == S_WR_IDLE)?1'b1:1'b0; // assign WR_FIFO_RE = (wr_state == S_WD_PROC)?M_AXI_WREADY:1'b0; localparam S_RD_IDLE = 3'd0; localparam S_RA_WAIT = 3'd1; localparam S_RA_START = 3'd2; localparam S_RD_WAIT = 3'd3; localparam S_RD_PROC = 3'd4; localparam S_RD_DONE = 3'd5; reg [2:0] rd_state; reg [31:0] reg_rd_adrs; reg [31:0] reg_rd_len; reg reg_arvalid, reg_r_last; reg [7:0] reg_r_len; assign RD_DONE = (rd_state == S_RD_DONE) ; // Read State always @(posedge ACLK or negedge ARESETN) begin if(!ARESETN) begin rd_state <= S_RD_IDLE; reg_rd_adrs[31:0] <= 32'd0; reg_rd_len[31:0] <= 32'd0; reg_arvalid <= 1'b0; reg_r_len[7:0] <= 8'd0; end else begin case(rd_state) S_RD_IDLE: begin if(RD_START) begin rd_state <= S_RA_WAIT; reg_rd_adrs[31:0] <= RD_ADRS[31:0]; reg_rd_len[31:0] <= RD_LEN[31:0] -32'd1; end reg_arvalid <= 1'b0; reg_r_len[7:0] <= 8'd0; end S_RA_WAIT: begin if(~RD_FIFO_AFULL) begin rd_state <= S_RA_START; end end S_RA_START: begin rd_state <= S_RD_WAIT; reg_arvalid <= 1'b1; reg_rd_len[31:11] <= reg_rd_len[31:11] -21'd1; if(reg_rd_len[31:11] != 21'd0) begin reg_r_last <= 1'b0; reg_r_len[7:0] <= 8'd255; end else begin reg_r_last <= 1'b1; reg_r_len[7:0] <= reg_rd_len[10:3]; end end S_RD_WAIT: begin if(M_AXI_ARREADY) begin rd_state <= S_RD_PROC; reg_arvalid <= 1'b0; end end S_RD_PROC: begin if(M_AXI_RVALID) begin if(M_AXI_RLAST) begin if(reg_r_last) begin rd_state <= S_RD_DONE; end else begin rd_state <= S_RA_WAIT; reg_rd_adrs[31:0] <= reg_rd_adrs[31:0] + 32'd2048; end end else begin reg_r_len[7:0] <= reg_r_len[7:0] -8'd1; end end end S_RD_DONE:begin rd_state <= S_RD_IDLE; end endcase end end // Master Read Address assign M_AXI_ARID = 1'b0; assign M_AXI_ARADDR[31:0] = reg_rd_adrs[31:0]; assign M_AXI_ARLEN[7:0] = reg_r_len[7:0]; assign M_AXI_ARSIZE[2:0] = 3'b011; assign M_AXI_ARBURST[1:0] = 2'b01; assign M_AXI_ARLOCK = 1'b0; assign M_AXI_ARCACHE[3:0] = 4'b0011; assign M_AXI_ARPROT[2:0] = 3'b000; assign M_AXI_ARQOS[3:0] = 4'b0000; assign M_AXI_ARUSER[0] = 1'b1; assign M_AXI_ARVALID = reg_arvalid; assign M_AXI_RREADY = M_AXI_RVALID & ~RD_FIFO_FULL; assign RD_READY = (rd_state == S_RD_IDLE)?1'b1:1'b0; assign RD_FIFO_WE = M_AXI_RVALID; assign RD_FIFO_DATA[63:0] = M_AXI_RDATA[63:0]; assign DEBUG[31:0] = {reg_wr_len[31:8], 1'd0, wr_state[2:0], 1'd0, rd_state[2:0]}; endmodule
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
- 81
- 82
- 83
- 84
- 85
- 86
- 87
- 88
- 89
- 90
- 91
- 92
- 93
- 94
- 95
- 96
- 97
- 98
- 99
- 100
- 101
- 102
- 103
- 104
- 105
- 106
- 107
- 108
- 109
- 110
- 111
- 112
- 113
- 114
- 115
- 116
- 117
- 118
- 119
- 120
- 121
- 122
- 123
- 124
- 125
- 126
- 127
- 128
- 129
- 130
- 131
- 132
- 133
- 134
- 135
- 136
- 137
- 138
- 139
- 140
- 141
- 142
- 143
- 144
- 145
- 146
- 147
- 148
- 149
- 150
- 151
- 152
- 153
- 154
- 155
- 156
- 157
- 158
- 159
- 160
- 161
- 162
- 163
- 164
- 165
- 166
- 167
- 168
- 169
- 170
- 171
- 172
- 173
- 174
- 175
- 176
- 177
- 178
- 179
- 180
- 181
- 182
- 183
- 184
- 185
- 186
- 187
- 188
- 189
- 190
- 191
- 192
- 193
- 194
- 195
- 196
- 197
- 198
- 199
- 200
- 201
- 202
- 203
- 204
- 205
- 206
- 207
- 208
- 209
- 210
- 211
- 212
- 213
- 214
- 215
- 216
- 217
- 218
- 219
- 220
- 221
- 222
- 223
- 224
- 225
- 226
- 227
- 228
- 229
- 230
- 231
- 232
- 233
- 234
- 235
- 236
- 237
- 238
- 239
- 240
- 241
- 242
- 243
- 244
- 245
- 246
- 247
- 248
- 249
- 250
- 251
- 252
- 253
- 254
- 255
- 256
- 257
- 258
- 259
- 260
- 261
- 262
- 263
- 264
- 265
- 266
- 267
- 268
- 269
- 270
- 271
- 272
- 273
- 274
- 275
- 276
- 277
- 278
- 279
- 280
- 281
- 282
- 283
- 284
- 285
- 286
- 287
- 288
- 289
- 290
- 291
- 292
- 293
- 294
- 295
- 296
- 297
- 298
- 299
- 300
- 301
- 302
- 303
- 304
- 305
- 306
- 307
- 308
- 309
- 310
- 311
- 312
- 313
- 314
- 315
- 316
- 317
- 318
- 319
- 320
- 321
- 322
- 323
- 324
- 325
- 326
- 327
- 328
- 329
- 330
- 331
- 332
- 333
- 334
- 335
- 336
- 337
- 338
- 339
- 340
- 341
- 342
- 343
- 344
- 345
- 346
- 347
- 348
- 349
- 350
- 351
- 352
- 353
- 354
- 355
- 356
- 357
- 358
- 359
- 360
- 361
- 362
- 363
- 364
- 365
- 366
- 367
- 368
- 369
- 370
- 371
- 372
- 373
- 374
- 375
- 376
- 377
- 378
- 379
- 380
- 381
- 382
- 383
- 384
- 385
- 386
- 387
- 388
- 389
module top( inout [14:0]DDR_addr, inout [2:0]DDR_ba, inout DDR_cas_n, inout DDR_ck_n, inout DDR_ck_p, inout DDR_cke, inout DDR_cs_n, inout [3:0]DDR_dm, inout [31:0]DDR_dq, inout [3:0]DDR_dqs_n, inout [3:0]DDR_dqs_p, inout DDR_odt, inout DDR_ras_n, inout DDR_reset_n, inout DDR_we_n, inout FIXED_IO_ddr_vrn, inout FIXED_IO_ddr_vrp, inout [53:0]FIXED_IO_mio, inout FIXED_IO_ps_clk, inout FIXED_IO_ps_porb, inout FIXED_IO_ps_srstb, output error ); wire rst_n; wire M_AXI_ACLK; // Master Write Address wire [0:0] M_AXI_AWID; wire [31:0] M_AXI_AWADDR; wire [7:0] M_AXI_AWLEN; // Burst Length: 0-255 wire [2:0] M_AXI_AWSIZE; // Burst Size: Fixed 2'b011 wire [1:0] M_AXI_AWBURST; // Burst Type: Fixed 2'b01(Incremental Burst) wire M_AXI_AWLOCK; // Lock: Fixed 2'b00 wire [3:0] M_AXI_AWCACHE; // Cache: Fiex 2'b0011 wire [2:0] M_AXI_AWPROT; // Protect: Fixed 2'b000 wire [3:0] M_AXI_AWQOS; // QoS: Fixed 2'b0000 wire [0:0] M_AXI_AWUSER; // User: Fixed 32'd0 wire M_AXI_AWVALID; wire M_AXI_AWREADY; // Master Write Data wire [63:0] M_AXI_WDATA; wire [7:0] M_AXI_WSTRB; wire M_AXI_WLAST; wire [0:0] M_AXI_WUSER; wire M_AXI_WVALID; wire M_AXI_WREADY; // Master Write Response wire [0:0] M_AXI_BID; wire [1:0] M_AXI_BRESP; wire [0:0] M_AXI_BUSER; wire M_AXI_BVALID; wire M_AXI_BREADY; // Master Read Address wire [0:0] M_AXI_ARID; wire [31:0] M_AXI_ARADDR; wire [7:0] M_AXI_ARLEN; wire [2:0] M_AXI_ARSIZE; wire [1:0] M_AXI_ARBURST; wire [1:0] M_AXI_ARLOCK; wire [3:0] M_AXI_ARCACHE; wire [2:0] M_AXI_ARPROT; wire [3:0] M_AXI_ARQOS; wire [0:0] M_AXI_ARUSER; wire M_AXI_ARVALID; wire M_AXI_ARREADY; // Master Read Data wire [0:0] M_AXI_RID; wire [63:0] M_AXI_RDATA; wire [1:0] M_AXI_RRESP; wire M_AXI_RLAST; wire [0:0] M_AXI_RUSER; wire M_AXI_RVALID; wire M_AXI_RREADY; (*mark_debug="true"*)wire wr_burst_data_req; (*mark_debug="true"*)wire wr_burst_finish; (*mark_debug="true"*)wire rd_burst_finish; (*mark_debug="true"*)wire rd_burst_req; (*mark_debug="true"*)wire wr_burst_req; (*mark_debug="true"*)wire[9:0] rd_burst_len; (*mark_debug="true"*)wire[9:0] wr_burst_len; (*mark_debug="true"*)wire[31:0] rd_burst_addr; (*mark_debug="true"*)wire[31:0] wr_burst_addr; (*mark_debug="true"*)wire rd_burst_data_valid; (*mark_debug="true"*)wire[63 : 0] rd_burst_data; (*mark_debug="true"*)wire[63 : 0] wr_burst_data; mem_test #( .MEM_DATA_BITS(64), .ADDR_BITS(27) ) mem_test_m0 ( .rst(~rst_n), .mem_clk(M_AXI_ACLK), .rd_burst_req(rd_burst_req), .wr_burst_req(wr_burst_req), .rd_burst_len(rd_burst_len), .wr_burst_len(wr_burst_len), .rd_burst_addr(rd_burst_addr), .wr_burst_addr(wr_burst_addr), .rd_burst_data_valid(rd_burst_data_valid), .wr_burst_data_req(wr_burst_data_req), .rd_burst_data(rd_burst_data), .wr_burst_data(wr_burst_data), .rd_burst_finish(rd_burst_finish), .wr_burst_finish(wr_burst_finish), .error(error) ); aq_axi_master u_aq_axi_master ( .ARESETN(rst_n), .ACLK(M_AXI_ACLK), .M_AXI_AWID(M_AXI_AWID), .M_AXI_AWADDR(M_AXI_AWADDR), .M_AXI_AWLEN(M_AXI_AWLEN), .M_AXI_AWSIZE(M_AXI_AWSIZE), .M_AXI_AWBURST(M_AXI_AWBURST), .M_AXI_AWLOCK(M_AXI_AWLOCK), .M_AXI_AWCACHE(M_AXI_AWCACHE), .M_AXI_AWPROT(M_AXI_AWPROT), .M_AXI_AWQOS(M_AXI_AWQOS), .M_AXI_AWUSER(M_AXI_AWUSER), .M_AXI_AWVALID(M_AXI_AWVALID), .M_AXI_AWREADY(M_AXI_AWREADY), .M_AXI_WDATA(M_AXI_WDATA), .M_AXI_WSTRB(M_AXI_WSTRB), .M_AXI_WLAST(M_AXI_WLAST), .M_AXI_WUSER(M_AXI_WUSER), .M_AXI_WVALID(M_AXI_WVALID), .M_AXI_WREADY(M_AXI_WREADY), .M_AXI_BID(M_AXI_BID), .M_AXI_BRESP(M_AXI_BRESP), .M_AXI_BUSER(M_AXI_BUSER), .M_AXI_BVALID(M_AXI_BVALID), .M_AXI_BREADY(M_AXI_BREADY), .M_AXI_ARID(M_AXI_ARID), .M_AXI_ARADDR(M_AXI_ARADDR), .M_AXI_ARLEN(M_AXI_ARLEN), .M_AXI_ARSIZE(M_AXI_ARSIZE), .M_AXI_ARBURST(M_AXI_ARBURST), .M_AXI_ARLOCK(M_AXI_ARLOCK), .M_AXI_ARCACHE(M_AXI_ARCACHE), .M_AXI_ARPROT(M_AXI_ARPROT), .M_AXI_ARQOS(M_AXI_ARQOS), .M_AXI_ARUSER(M_AXI_ARUSER), .M_AXI_ARVALID(M_AXI_ARVALID), .M_AXI_ARREADY(M_AXI_ARREADY), .M_AXI_RID(M_AXI_RID), .M_AXI_RDATA(M_AXI_RDATA), .M_AXI_RRESP(M_AXI_RRESP), .M_AXI_RLAST(M_AXI_RLAST), .M_AXI_RUSER(M_AXI_RUSER), .M_AXI_RVALID(M_AXI_RVALID), .M_AXI_RREADY(M_AXI_RREADY), .MASTER_RST(~rst_n), .WR_START(wr_burst_req), .WR_ADRS({wr_burst_addr[28:0],3'd0}), .WR_LEN({wr_burst_len,3'd0}), .WR_READY(), .WR_FIFO_RE(wr_burst_data_req), .WR_FIFO_EMPTY(1'b0), .WR_FIFO_AEMPTY(1'b0), .WR_FIFO_DATA(wr_burst_data), .WR_DONE(wr_burst_finish), .RD_START(rd_burst_req), .RD_ADRS({rd_burst_addr[28:0],3'd0}), .RD_LEN({rd_burst_len,3'd0}), .RD_READY(), .RD_FIFO_WE(rd_burst_data_valid), .RD_FIFO_FULL(1'b0), .RD_FIFO_AFULL(1'b0), .RD_FIFO_DATA(rd_burst_data), .RD_DONE(rd_burst_finish), .DEBUG() ); hdmi_out_wrapper ps_block ( .DDR_addr(DDR_addr), .DDR_ba(DDR_ba), .DDR_cas_n(DDR_cas_n), .DDR_ck_n(DDR_ck_n), .DDR_ck_p(DDR_ck_p), .DDR_cke(DDR_cke), .DDR_cs_n(DDR_cs_n), .DDR_dm(DDR_dm), .DDR_dq(DDR_dq), .DDR_dqs_n(DDR_dqs_n), .DDR_dqs_p(DDR_dqs_p), .DDR_odt(DDR_odt), .DDR_ras_n(DDR_ras_n), .DDR_reset_n(DDR_reset_n), .DDR_we_n(DDR_we_n), .FIXED_IO_ddr_vrn(FIXED_IO_ddr_vrn), .FIXED_IO_ddr_vrp(FIXED_IO_ddr_vrp), .FIXED_IO_mio(FIXED_IO_mio), .FIXED_IO_ps_clk(FIXED_IO_ps_clk), .FIXED_IO_ps_porb(FIXED_IO_ps_porb), .FIXED_IO_ps_srstb(FIXED_IO_ps_srstb), .S00_AXI_araddr (M_AXI_ARADDR ), .S00_AXI_arburst (M_AXI_ARBURST ), .S00_AXI_arcache (M_AXI_ARCACHE ), .S00_AXI_arid (M_AXI_ARID ), .S00_AXI_arlen (M_AXI_ARLEN ), .S00_AXI_arlock (M_AXI_ARLOCK ), .S00_AXI_arprot (M_AXI_ARPROT ), .S00_AXI_arqos (M_AXI_ARQOS ), .S00_AXI_arready (M_AXI_ARREADY ), //.S00_AXI_arregion (4'b0000 ), .S00_AXI_arsize (M_AXI_ARSIZE ), .S00_AXI_arvalid (M_AXI_ARVALID ), .S00_AXI_rdata (M_AXI_RDATA ), .S00_AXI_rid (M_AXI_RID ), .S00_AXI_rlast (M_AXI_RLAST ), .S00_AXI_rready (M_AXI_RREADY ), .S00_AXI_rresp (M_AXI_RRESP ), .S00_AXI_rvalid (M_AXI_RVALID ), .S00_AXI_awaddr (M_AXI_AWADDR ), .S00_AXI_awburst (M_AXI_AWBURST ), .S00_AXI_awcache (M_AXI_AWCACHE ), .S00_AXI_awid (M_AXI_AWID ), .S00_AXI_awlen (M_AXI_AWLEN ), .S00_AXI_awlock (M_AXI_AWLOCK ), .S00_AXI_awprot (M_AXI_AWPROT ), .S00_AXI_awqos (M_AXI_AWQOS ), .S00_AXI_awready (M_AXI_AWREADY ), //.S00_AXI_awregion (4'b0000 ), .S00_AXI_awsize (M_AXI_AWSIZE ), .S00_AXI_awvalid (M_AXI_AWVALID ), .S00_AXI_bid (M_AXI_BID ), .S00_AXI_bready (M_AXI_BREADY ), .S00_AXI_bresp (M_AXI_BRESP ), .S00_AXI_bvalid (M_AXI_BVALID ), .S00_AXI_wdata (M_AXI_WDATA ), .S00_AXI_wlast (M_AXI_WLAST ), .S00_AXI_wready (M_AXI_WREADY ), .S00_AXI_wstrb (M_AXI_WSTRB ), .S00_AXI_wvalid (M_AXI_WVALID ), .peripheral_aresetn(rst_n), .FCLK_CLK0(M_AXI_ACLK), .axi_hp_clk(M_AXI_ACLK) ); endmodule
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
- 81
- 82
- 83
- 84
- 85
- 86
- 87
- 88
- 89
- 90
- 91
- 92
- 93
- 94
- 95
- 96
- 97
- 98
- 99
- 100
- 101
- 102
- 103
- 104
- 105
- 106
- 107
- 108
- 109
- 110
- 111
- 112
- 113
- 114
- 115
- 116
- 117
- 118
- 119
- 120
- 121
- 122
- 123
- 124
- 125
- 126
- 127
- 128
- 129
- 130
- 131
- 132
- 133
- 134
- 135
- 136
- 137
- 138
- 139
- 140
- 141
- 142
- 143
- 144
- 145
- 146
- 147
- 148
- 149
- 150
- 151
- 152
- 153
- 154
- 155
- 156
- 157
- 158
- 159
- 160
- 161
- 162
- 163
- 164
- 165
- 166
- 167
- 168
- 169
- 170
- 171
- 172
- 173
- 174
- 175
- 176
- 177
- 178
- 179
- 180
- 181
- 182
- 183
- 184
- 185
- 186
- 187
- 188
- 189
- 190
- 191
- 192
- 193
- 194
- 195
- 196
- 197
- 198
- 199
- 200
- 201
- 202
- 203
- 204
- 205
- 206
- 207
- 208
- 209
- 210
- 211
- 212
- 213
- 214
- 215
- 216
- 217
- 218
- 219
- 220
- 221
- 222
- 223
- 224
- 225
- 226
- 227
- 228
- 229
- 230
- 231
- 232
- 233
- 234
- 235
- 236
- 237
- 238
- 239
- 240
- 241
- 242
- 243
- 244
- 245
- 246
- 247
- 248
- 249
- 250
- 251
- 252
- 253
- 254
- 255
- 256
- 257
- 258
- 259
- 260
- 261
- 262
- 263
3下板测试
读写分析
声明：本文内容由网友自发贡献，不代表【wpsshop博客】立场，版权归原作者所有，本站不承担相应法律责任。如您发现有侵权的内容，请联系我们。转载请注明出处：https://www.wpsshop.cn/w/Monodyee/article/detail/478886
推荐阅读
相关标签
