Arduino UNO与ESP8266串口连接_arduino uno连接esp8266

1. ESP8266烧录AT固件

1.1 烧录软件下载

登录乐鑫官网下载地址，下载Flash 下载工具。

1.2 烧录AT固件

首先，点击安信可AT固件下载地址,下载出厂默认 AT 固件。
然后打开Flash Download Tools,点击Download ESP8266，如图所示：

在COM处选择端口号，点击START连接。此时,DETECTED INFO会显示连接的ESP8266硬件信息，包括晶振频率和Flash Size。选择DoNotChgBin，并选择下载的AT固件文件，设置地址为0x00000，设置其余参数和ESP8266信号一致。点击ERASE清空FLASH，点击START开始写入直到完成。

2. ESP8266 AT指令

• 注意透传只能在单连接模式下进行，所以在建立连接之前一定要用（AT+CIPMUX=0设置单连接），但是模块处于服务器模式下时，必须要多链接，由于冲突，所以模块开启服务器模式不能做 TCP透传！

//模块通过数据外网透传
AT+CWMODE=3                        设置 AP 和 STA 共存模式
AT+CWLAP                            查询附近 WIFI
AT+CWJAP="HUAWEI-C4VTTJ","1234567890"           连接 wifi
AT+CIPMUX=0                          设置单连接
AT+CIPMODE=1                        设置透传模式
AT+CIPSTART="TCP","115.29.109.104",6602    连接外网服务器，请参考下面网址
AT+CIPSEND
1
2
3
4
5
6
7
8

3. Arduino UNO 串口连接方式

• D2、D3为arduino设置的软串口RX和TX。

4. Arduino UNO与ESP8266-12f串口连接

Arduino IDE官网下载连接，Arduino UNO端程序如下：

#include <SoftwareSerial.h>

#define DEBUG true

SoftwareSerial esp8266(2,3); // make RX Arduino line is pin 2, make TX Arduino line is pin 3.
                             // This means that you need to connect the TX line from the esp to the Arduino's pin 2
                             // and the RX line from the esp to the Arduino's pin 3
void setup()
{
  Serial.begin(9600);
  esp8266.begin(9600); // your esp's baud rate might be different

  pinMode(11,OUTPUT);
  digitalWrite(11,LOW);

  pinMode(12,OUTPUT);
  digitalWrite(12,LOW);

  pinMode(13,OUTPUT);
  digitalWrite(13,LOW);

  sendCommand("AT+RST\r\n",2000,DEBUG); // reset module
  setAP("ESP8266","w12345678");
  Serial.println("Server Ready");
}

void loop()
{
  if(esp8266.available()) // check if the esp is sending a message 
  {
    if(esp8266.find("+IPD,"))
    {
     delay(1000); // wait for the serial buffer to fill up (read all the serial data)
     // get the connection id so that we can then disconnect
     int connectionId = esp8266.read()-48; // subtract 48 because the read() function returns 
                                           // the ASCII decimal value and 0 (the first decimal number) starts at 48

     esp8266.find("pin="); // advance cursor to "pin="

     int pinNumber = (esp8266.read()-48); // get first number i.e. if the pin 13 then the 1st number is 1
     int secondNumber = (esp8266.read()-48);
     if(secondNumber>=0 && secondNumber<=9)
     {
      pinNumber*=10;
      pinNumber +=secondNumber; // get second number, i.e. if the pin number is 13 then the 2nd number is 3, then add to the first number
     }

     digitalWrite(pinNumber, !digitalRead(pinNumber)); // toggle pin    

     // build string that is send back to device that is requesting pin toggle
     String content;
     content = "Pin ";
     content += pinNumber;
     content += " is ";

     if(digitalRead(pinNumber))
     {
       content += "ON";
     }
     else
     {
       content += "OFF";
     }

     sendHTTPResponse(connectionId,content);

     // make close command
     String closeCommand = "AT+CIPCLOSE="; 
     closeCommand+=connectionId; // append connection id
     closeCommand+="\r\n";

     sendCommand(closeCommand,1000,DEBUG); // close connection
    }
  }
}

void setAP(String wifi,String passwd)
{
    sendCommand("AT+CWMODE=2\r\n",1000,DEBUG); // 开启 AP 模式
    sendCommand("AT+CWSAP=\""+wifi+"\",\""+passwd+"\",11,0\r\n",3000,DEBUG);
}

void setSTA(String wifi,String passwd)
{
    sendCommand("AT+CWMODE=1\r\n",1000,DEBUG); // 开启 STA 模式
    sendCommand("AT+CWJAP=\""+wifi+"\",\""+passwd+"\"\r\n",3000,DEBUG);
    delay(10000);
    sendCommand("AT+CIFSR\r\n",1000,DEBUG); // get ip address
    sendCommand("AT+CIPMUX=1\r\n",1000,DEBUG); // configure for multiple connections
    sendCommand("AT+CIPSERVER=1,80\r\n",1000,DEBUG); // turn on server on port 80
}

/*
* Name: sendData
* Description: Function used to send data to ESP8266.
* Params: command - the data/command to send; timeout - the time to wait for a response; debug - print to Serial window?(true = yes, false = no)
* Returns: The response from the esp8266 (if there is a reponse)
*/
String sendData(String command, const int timeout, boolean debug)
{
    String response = "";

    int dataSize = command.length();
    char data[dataSize];
    command.toCharArray(data,dataSize);

    esp8266.write(data,dataSize); // send the read character to the esp8266
    if(debug)
    {
      Serial.println("\r\n====== HTTP Response From Arduino ======");
      Serial.write(data,dataSize);
      Serial.println("\r\n========================================");
    }

    long int time = millis();

    while( (time+timeout) > millis())
    {
      while(esp8266.available())
      {

        // The esp has data so display its output to the serial window 
        char c = esp8266.read(); // read the next character.
        response+=c;
      }  
    }

    if(debug)
    {
      Serial.print(response);
    }

    return response;
}

/*
* Name: sendHTTPResponse
* Description: Function that sends HTTP 200, HTML UTF-8 response
*/
void sendHTTPResponse(int connectionId, String content)
{

     // build HTTP response
     String httpResponse;
     String httpHeader;
     // HTTP Header
     httpHeader = "HTTP/1.1 200 OK\r\nContent-Type: text/html; charset=UTF-8\r\n"; 
     httpHeader += "Content-Length: ";
     httpHeader += content.length();
     httpHeader += "\r\n";
     httpHeader +="Connection: close\r\n\r\n";
     httpResponse = httpHeader + content + " "; // There is a bug in this code: the last character of "content" is not sent, I cheated by adding this extra space
     sendCIPData(connectionId,httpResponse);
}

/*
* Name: sendCIPDATA
* Description: sends a CIPSEND=<connectionId>,<data> command
*
*/
void sendCIPData(int connectionId, String data)
{
   String cipSend = "AT+CIPSEND=";
   cipSend += connectionId;
   cipSend += ",";
   cipSend +=data.length();
   cipSend +="\r\n";
   sendCommand(cipSend,1000,DEBUG);
   sendData(data,1000,DEBUG);
}

/*
* Name: sendCommand
* Description: Function used to send data to ESP8266.
* Params: command - the data/command to send; timeout - the time to wait for a response; debug - print to Serial window?(true = yes, false = no)
* Returns: The response from the esp8266 (if there is a reponse)
*/
String sendCommand(String command, const int timeout, boolean debug)
{
    String response = "";

    esp8266.print(command); // send the read character to the esp8266

    long int time = millis();

    while( (time+timeout) > millis())
    {
      while(esp8266.available())
      {

        // The esp has data so display its output to the serial window 
        char c = esp8266.read(); // read the next character.
        response+=c;
      }  
    }

    if(debug)
    {
      Serial.print(response);
    }

    return response;
}
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203

5. 串口调试

打开Arduino IDE串口调试工具—>串口监视器，无需调试，静静地看着就好了。