vlan的三层交换连通_三层交换机vlan间互通

通过三层交换机实现 VLAN 间互通。 通过单臂路由实现 VLAN 间互通

实验一：通过三层交换机实现 VLAN 间互通。
网络拓扑图：

配置PC的IP地址、子网掩码、网关：

配置交换机S1的接口为Trunk，G0/0/1允许vlan 10通过、G0/0/2允许vlan 20 通过

[S1]vlan batch 10 20
[S1]int g0/0/1
[S1-GigabitEthernet0/0/1]port link-type trunk 	
[S1-GigabitEthernet0/0/1]port trunk allow-pass vlan 10
[S1-GigabitEthernet0/0/1]int g0/0/2	
[S1-GigabitEthernet0/0/2]port link-type trunk 	
[S1-GigabitEthernet0/0/2]port trunk allow-pass vlan 20
[S1-GigabitEthernet0/0/2]quit
[S1]
1
2
3
4
5
6
7
8
9

配置S1两个vlan的IP地址：

[S1]int vlanif 10
[S1-Vlanif10]ip add 192.168.100.1 24
[S1-Vlanif10]quit
[S1]int vlanif 20
[S1-Vlanif20]ip add 192.168.200.1 24
1
2
3
4
5

查看S1的配置路由结果

[S1]dis ip routing-table 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 6        Routes : 6        

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
  192.168.100.0/24  Direct  0    0           D   192.168.100.1   Vlanif10
  192.168.100.1/32  Direct  0    0           D   127.0.0.1       Vlanif10
  192.168.200.0/24  Direct  0    0           D   192.168.200.1   Vlanif20
  192.168.200.1/32  Direct  0    0           D   127.0.0.1       Vlanif20

[S1]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

接着配置S2的vlan10和连接pc端接口的Access接口：

[S2]vlan 10
[S2-vlan10]quit
[S2]int vlanif 10
[S2-Vlanif10]ip add 192.168.100.1 24
[S2]int e0/0/1	
[S2-Ethernet0/0/1]port link-type access 
[S2-Ethernet0/0/1]port default vlan 10
[S2-Ethernet0/0/1]int e0/0/2	
[S2-Ethernet0/0/2]port link-type access
[S2-Ethernet0/0/2]port default vlan 10
[S2-Ethernet0/0/2]
1
2
3
4
5
6
7
8
9
10
11

同理配置S3：

[S3]vlan 20
[S3-vlan20]quit
[S3]int vlanif 20
[S3-Vlanif20]ip add 192.168.200.1 24
[S3]int e0/0/1
[S3-Ethernet0/0/1]port link-type access
[S3-Ethernet0/0/1]port default vlan 20
[S3-Ethernet0/0/1]int e0/0/2
[S3-Ethernet0/0/2]port link-type access
[S3-Ethernet0/0/2]port default vlan 20
[S3-Ethernet0/0/2]
1
2
3
4
5
6
7
8
9
10
11

接下来配置S2、S3连接三层交换机S1那一个接口为Trunk接口：

[S2-Ethernet0/0/2]int g0/0/1	
[S2-GigabitEthernet0/0/1]port link-type trunk 
[S2-GigabitEthernet0/0/1]port trunk allow-pass vlan all
1
2
3

[S3-Ethernet0/0/2]int g0/0/1
[S3-GigabitEthernet0/0/1]port link-type trunk 	
[S3-GigabitEthernet0/0/1]port trunk allow-pass vlan all

1
2
3
4

测试全网是否互通：
此处测试PC1ping通PC2和PC4ping通PC3

实验二：通过单臂路由实现Vlan间互通
网络拓扑图：

配置PC的IP 、子网掩码、网关：

首先配置S1的trunk接口：

[S1]int g0/0/1	
[S1-GigabitEthernet0/0/1]port link-type trunk 
[S1-GigabitEthernet0/0/1]port trunk allow-pass vlan all
1
2
3

接着配置S1的两个连接PC的Access接口：

[S1]vlan batch 10 20
[S1]int g0/0/2
[S1-GigabitEthernet0/0/2]port link-type access 	
[S1-GigabitEthernet0/0/2]port default vlan 10
[S1-GigabitEthernet0/0/2]int g0/0/3	
[S1-GigabitEthernet0/0/3]port link-type access 	
[S1-GigabitEthernet0/0/3]port default vlan 20
1
2
3
4
5
6
7

紧接着在Router上创建两个子接口，每个子接口配置IP地址和dot1Q封装VLANID

[R1]int g0/0/0.10
[R1-GigabitEthernet0/0/0.10]ip add 192.168.1.254 24	
[R1-GigabitEthernet0/0/0.10]dot1q termination vid 10	
[R1-GigabitEthernet0/0/0.10]arp broadcast enable 
[R1-GigabitEthernet0/0/0.10]int g0/0/0.20
[R1-GigabitEthernet0/0/0.20]ip add 192.168.2.254 24
[R1-GigabitEthernet0/0/0.20]dot1q termination vid 20
[R1-GigabitEthernet0/0/0.20]arp broadcast enable 
1
2
3
4
5
6
7
8

其中封装dot1q协议，这两个子接口分别对应vlan10和对应vlan20、并开启子接口的ARP广播
检测网络是否互通: