TX2 flash.sh 刷机_error: probing the target board failed. make sure

flash.sh 刷机

#!/bin/bash

# Copyright (c) 2011-2021, NVIDIA CORPORATION.  All rights reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
#  * Redistributions of source code must retain the above copyright
#    notice, this list of conditions and the following disclaimer.
#  * Redistributions in binary form must reproduce the above copyright
#    notice, this list of conditions and the following disclaimer in the
#    documentation and/or other materials provided with the distribution.
#  * Neither the name of NVIDIA CORPORATION nor the names of its
#    contributors may be used to endorse or promote products derived
#    from this software without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ``AS IS'' AND ANY
# EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
# PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE COPYRIGHT OWNER OR
# CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
# EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
# PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
# OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.


#
# flash.sh: Flash the target board.
#	    flash.sh performs the best in LDK release environment.
#
# Usage: Place the board in recovery mode and run:
#
#	flash.sh [options] <target_board> <root_device>
#
#	for more detail enter 'flash.sh -h'
#
# Examples:
# ./flash.sh <target_board> internal			- boot <target_board> from on-board device (eMMC/SDCARD)
# ./flash.sh <target_board> external			- boot <target_board> from external device
# ./flash.sh <target_board> mmcblk0p1			- boot <target_board> from eMMC
# ./flash.sh <target_board> mmcblk1p1			- boot <target_board> from SDCARD
# ./flash.sh <target_board> sda1			- boot <target_board> from USB device
# ./flash.sh <target_board> nvme0n1			- boot <target_board> from NVME storage device
# ./flash.sh -N <IPaddr>:/nfsroot <target_board> eth0	- boot <target_board> from NFS
# ./flash.sh -k LNX <target_board> mmcblk1p1		- update <target_board> kernel
# ./flash.sh -k EBT <target_board> mmcblk1p1		- update <target_board> bootloader
#
# Optional Environment Variables:
# BCTFILE ---------------- Boot control table configuration file to be used.
# BOARDID ---------------- Pass boardid to override EEPROM value
# BOARDREV --------------- Pass board_revision to override EEPROM value
# BOARDSKU --------------- Pass board_sku to override EEPROM value
# BOOTLOADER ------------- Bootloader binary to be flashed
# BOOTPARTLIMIT ---------- GPT data limit. (== Max BCT size + PPT size)
# BOOTPARTSIZE ----------- Total eMMC HW boot partition size.
# CFGFILE ---------------- Partition table configuration file to be used.
# CMDLINE ---------------- Target cmdline. See help for more information.
# DEVSECTSIZE ------------ Device Sector size. (default = 512Byte).
# DTBFILE ---------------- Device Tree file to be used.
# EMMCSIZE --------------- Size of target device eMMC (boot0+boot1+user).
# FLASHAPP --------------- Flash application running in host machine.
# FLASHER ---------------- Flash server running in target machine.
# INITRD ----------------- Initrd image file to be flashed.
# KERNEL_IMAGE ----------- Linux kernel zImage file to be flashed.
# MTS -------------------- MTS file name such as mts_si.
# MTSPREBOOT ------------- MTS preboot file name such as mts_preboot_si.
# NFSARGS ---------------- Static Network assignments.
#			   <C-ipa>:<S-ipa>:<G-ipa>:<netmask>
# NFSROOT ---------------- NFSROOT i.e. <my IP addr>:/exported/rootfs_dir.
# NO_RECOVERY_IMG -------- Do not create or re-create recovery.img
# NO_ROOTFS -------------- Do not create or re-create system.img
# ODMDATA ---------------- Odmdata to be used.
# PKCKEY ----------------- RSA key file to used to sign bootloader images.
# ROOTFSSIZE ------------- Linux RootFS size (internal emmc/nand only).
# ROOTFS_DIR ------------- Linux RootFS directory name.
# SBKKEY ----------------- SBK key file to used to encrypt bootloader images.
# SCEFILE ---------------- SCE firmware file such as camera-rtcpu-sce.img.
# SPEFILE ---------------- SPE firmware file path such as bootloader/spe.bin.
# FAB -------------------- Target board's FAB ID.
# TEGRABOOT -------------- lowerlayer bootloader such as nvtboot.bin.
# WB0BOOT ---------------- Warmboot code such as nvtbootwb0.bin
#
INFODIVIDER="\
###############################################################################\
";

chkerr ()
{
	if [ $? -ne 0 ]; then
		if [ "$1" != "" ]; then
			echo "$1";
		else
			echo "failed.";
		fi;
		exit 1;
	fi;
	if [ "$1" = "" ]; then
		echo "done.";
	fi;
}

pr_conf()
{
	echo "target_board=${target_board}";
	echo "target_rootdev=${target_rootdev}";
	echo "rootdev_type=${rootdev_type}";
	echo "rootfssize=${rootfssize}";
	echo "odmdata=${odmdata}";
	echo "flashapp=${flashapp}";
	echo "flasher=${flasher}";
	echo "bootloader=${bootloader}";
	echo "tegraboot=${tegraboot}";
	echo "wb0boot=${wb0boot}";
	echo "mtspreboot=${mtspreboot}";
	echo "mts=${mts}";
	echo "bctfile=${bctfile}";
	echo "cfgfile=${cfgfile}";
	echo "kernel_fs=${kernel_fs}";
	echo "kernel_image=${kernel_image}";
	echo "dtbfile=${dtbfile}"
	echo "rootfs_dir=${rootfs_dir}";
	echo "nfsroot=${nfsroot}";
	echo "nfsargs=${nfsargs}";
	echo "kernelinitrd=${kernelinitrd}";
	echo "cmdline=${cmdline}";
	echo "boardid=${boardid}";
}

validateIP ()
{
	local ip=$1;
	local ret=1;

	if [[ $ip =~ ^[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}$ ]]; then
		OIFS=${IFS};
		IFS='.';
		ip=($ip);
		IFS=${OIFS};
		[[ ${ip[0]} -le 255 && ${ip[1]} -le 255 && \
		   ${ip[2]} -le 255 && ${ip[3]} -le 255 ]];
		ret=$?;
	fi;
	if [ ${ret} -ne 0 ]; then
		echo "Invalid IP address: $1";
		exit 1;
	fi;
}

netmasktbl=(\
	"255.255.255.252" \
	"255.255.255.248" \
	"255.255.255.240" \
	"255.255.255.224" \
	"255.255.255.192" \
	"255.255.255.128" \
	"255.255.255.0" \
	"255.255.254.0" \
	"255.255.252.0" \
	"255.255.248.0" \
	"255.255.240.0" \
	"255.255.224.0" \
	"255.255.192.0" \
	"255.255.128.0" \
	"255.255.0.0" \
	"255.254.0.0" \
	"255.252.0.0" \
	"255.248.0.0" \
	"255.240.0.0" \
	"255.224.0.0" \
	"255.192.0.0" \
	"255.128.0.0" \
	"255.0.0.0" \
);

validateNETMASK ()
{
	local i;
	local nm=$1;
	for (( i=0; i<${#netmasktbl[@]}; i++ )); do
		if [ "${nm}" = ${netmasktbl[$i]} ]; then
			return 0;
		fi;
	done;
	echo "Error: Invalid netmask($1)";
	exit 1;
}

validateNFSargs ()
{
	local a=$2;

	OIFS=${IFS};
	IFS=':';
	a=($a);
	IFS=${OIFS};

	if [ ${#a[@]} -ne 4 ]; then
		echo "Error: Invalid nfsargs($2)";
		exit 1;
	fi;
	validateIP ${a[0]};
	if [ "${serverip}" = "" ]; then
		validateIP ${a[1]};
	fi;
	validateIP ${a[2]};
	validateNETMASK ${a[3]};
	if [ "$1" != "" ]; then
		eval "$1=$2";
	fi;
	return 0;
}

validateNFSroot ()
{
	if [ "$2" = "" ]; then
		return 1;
	fi;
	OIFS=${IFS};
	IFS=':';
	local var=$1;
	local a=($2);
	IFS=${OIFS};
	if [ ${#a[@]} -ne 2 ]; then
		echo "Error: Invalid nfsroot($2)";
		exit 1;
	fi;
	validateIP ${a[0]};
	if [[ "${a[1]}" != /* ]]; then
		echo "Error: Invalid nfsroot($2)";
		exit 1;
	fi;
	eval "${var}=$2";
	return 0;
}

usage ()
{
	state=$1;
	retval=$2;

	if [[ $state == allunknown ]]; then
		echo -e "
Usage: sudo ./flash.sh [options] <target_board> <rootdev>
  Where,
	target board: Valid target board name.
	rootdev: Proper root device.";

	elif [[ $state == rootdevunknown ]]; then
		echo -e "
Usage: sudo ./flash.sh [options] ${target_board} <rootdev>
  Where,
    rootdev for ${target_board}:
	${ROOT_DEV}";

	else
		echo "
Usage: sudo ./flash.sh [options] ${target_board} ${target_rootdev}";
	fi;

	cat << EOF
    options:
        -b <bctfile> --------- Boot control table config file.
        -c <cfgfile> --------- Flash partition table config file.
        -d <dtbfile> --------- device tree file.
        -e <emmc size> ------- Target device's eMMC size.
        -f <flashapp> -------- Path to flash application (tegraflash.py)
        -h ------------------- print this message.
        -i <enc rfs key file>- key for disk encryption support.
        -k <partition id> ---- partition name or number specified in flash.cfg.
        -m <mts preboot> ----- MTS preboot such as mts_preboot_si.
        -n <nfs args> -------- Static nfs network assignments
                               <Client IP>:<Server IP>:<Gateway IP>:<Netmask>
        -o <odmdata> --------- ODM data.
        -p <bp size> --------- Total eMMC HW boot partition size.
        -r ------------------- skip building and reuse existing system.img.
        -s <PKC key file>----- PKC key used for signing and building bl_update_payload.
                               (obsolete)
        -t <tegraboot> ------- tegraboot binary such as nvtboot.bin
        -u <PKC key file>----- PKC key used for odm fused board.
        -v <SBK key file>----- Secure Boot Key (SBK) key used for ODM fused board.
        -w <wb0boot> --------- warm boot binary such as nvtbootwb0.bin
        -x <tegraid> --------- Tegra CHIPID. default = 0x18(jetson-tx2)
                               0x21(jetson-tx1).
        -y <fusetype> -------- PKC for secureboot, NS for non-secureboot.
        -z <sn> -------------- Serial Number of target board.
        -B <boardid> --------- BoardId.
        -C <cmdline> --------- Kernel commandline arguments.
                               WARNING:
                               Each option in this kernel commandline gets
                               higher preference over the values set by
                               flash.sh. In case of NFS booting, this script
                               adds NFS booting related arguments, if -i option
                               is omitted.
        -F <flasher> --------- Flash server such as cboot.bin.
        -G <file name> ------- Read partition and save image to file.
        -I <initrd> ---------- initrd file. Null initrd is default.
        -K <kernel> ---------- Kernel image file such as zImage or Image.
        -L <bootloader> ------ Bootloader such as cboot.bin or u-boot-dtb.bin.
        -M <mts boot> -------- MTS boot file such as mts_si.
        -N <nfsroot> --------- i.e. <my IP addr>:/my/exported/nfs/rootfs.
        -P <end of PPT + 1> -- Primary GPT start address + size of PPT + 1.
        -R <rootfs dir> ------ Sample rootfs directory.
        -S <size> ------------ Rootfs size in bytes. Valid only for internal
                               rootdev. KiB, MiB, GiB short hands are allowed,
                               for example, 1GiB means 1024 * 1024 * 1024 bytes.
        -Z ------------------- Print configurations and then exit.
        --no-flash ----------- perform all steps except physically flashing the board.
                               This will create a system.img.
        --external-device----- Generate flash images for external devices
        --no-systemimg ------- Do not create or re-create system.img.
        --bup ---------------- Generate bootloader update payload(BUP).
        --multi-spec---------- Enable support for building multi-spec BUP.
        --clean-up------------ Clean up BUP buffer when multi-spec is enabled.
        --rapid-boot-----------Rapid-boot support on Jetson-Nano.
        --usb-instance <id> -- Specify the USB instance to connect to;
                               <id> = USB port path (e.g. 3-14).
        --no-root-check ------ Typical usage of this script require root permissions.
                               Pass this option to allow running the script as a
                               regular user, in which case only specific combinations
                               of command-line options will be functional.
        --user_key <key_file>  User provided key file (16-byte) to encrypt user images,
                               like kernel, kernel-dtb and initrd.
                               If user_key is specified, SBK key (-v) has to be specified.
        --rcm-boot ----------- Do RCM boot instead of physically flashing the board.
        --sign --------------- Sign images and store them under "bootloader/signed"
                               directory. The board will not be physically flashed.
        --image -------------- Specify the image to be written into board.
EOF
	exit $retval;
}

setdflt ()
{
	local var="$1";
	if [ "${!var}" = "" ]; then
		eval "${var}=\"$2\"";
	fi;
}

setval ()
{
	local var="$1";
	local val="$2";
	if [ "${!val}" = "" ]; then
		echo "Error: missing $val not defined.";
		exit 1;
	fi;
	eval "${var}=\"${!val}\"";
}

mkfilesoft ()
{
	local var="$1";
	local varname="$1name";

	eval "${var}=\"$2\"";
	if [ "${!var}" = "" -o ! -f "${!var}" ]; then
		if [ "$3" != "" -a -f "$3" ]; then
			eval "${var}=\"$3\"";
		fi;
	fi;
	if [ "${!var}" != "" ]; then
		if [ ! -f "${!var}" ]; then
			eval "${var}=\"\"";
			eval "${varname}=\"\"";
			return 1;
		fi;
		eval "${var}=\"$(readlink -f "${!var}")\"";
		eval "${varname}=\"$(basename "${!var}")\"";
	fi;
	return 0;
}

mkfilepath ()
{
	local var="$1";
	local varname="$1name";

	eval "${var}=\"$2\"";
	setdflt "${var}" "$3";
	if [ "${!var}" != "" ]; then
		eval "${var}=\"$(readlink -f "${!var}")\"";
		if [ ! -f "${!var}" ]; then
			echo "Error: missing $var (${!var}).";
			usage allknown 1;
		fi;
		eval "${varname}=\"$(basename "${!var}")\"";
	fi;
}

mkdirpath ()
{
	local var="$1";
	eval "${var}=$2";
	setdflt "$1" "$3";
	if [ "${!var}" != "" ]; then
		eval "${var}=\"$(readlink -f "${!var}")\"";
		if [ ! -d "${!var}" ]; then
			echo "Error: missing $var (${!var}).";
			usage allknown 1;
		fi;
	fi;
}

getsize ()
{
	local var="$1";
	local val="$2";
	if [[ ${!val} != *[!0-9]* ]]; then
		eval "${var}=${!val}";
	elif [[ (${!val} == *KiB) && (${!val} != *[!0-9]*KiB) ]]; then
		eval "${var}=$(( ${!val%KiB} * 1024 ))";
	elif [[ (${!val} == *MiB) && (${!val} != *[!0-9]*MiB) ]]; then
		eval "${var}=$(( ${!val%MiB} * 1024 * 1024 ))";
	elif [[ (${!val} == *GiB) && (${!val} != *[!0-9]*GiB) ]]; then
		eval "${var}=$(( ${!val%GiB} * 1024 * 1024 * 1024))";
	else
		echo "Error: Invalid $1: ${!val}";
		exit 1;
	fi;
}

validatePartID ()
{
	local idx=0;
	declare -A cf;

	while read aline; do
		if [ "$aline" != "" ]; then
			arr=( $(echo $aline | tr '=' ' ') );
			if [ "${arr[1]}" == "name" ]; then
				if [ "${arr[3]}" == "id" ]; then
					cf[$idx,1]="${arr[2]}";
					cf[$idx,0]="${arr[4]}";
				else
					cf[$idx,0]="${arr[2]}";
				fi
				idx=$((idx+1));
			fi
		fi;
	done < $4;

	if [ "${arr[3]}" == "id" ]; then
		for ((i = 0; i < idx; i++)) do
			if [ "\"$3\"" = "${cf[$i,0]}" -o  \
			     "\"$3\"" = "${cf[$i,1]}" ]; then
				eval "$1=${cf[$i,0]}";
				eval "$2=${cf[$i,1]}";
			return 0;
			fi;
		done;
		echo "Error: invalid partition id ($3)";
		exit 1;
	else
		return 0;
	fi;
}

cp2local ()
{
	local src=$1;
	if [ "${!src}" = "" ]; then return 1; fi;
	if [ ! -f "${!src}" ]; then return 1; fi;
	if [ "$2" = "" ];      then return 1; fi;
	if [ -f "$2" -a "${!src}" = "$2" ]; then
		local sum1=$(sum "${!src}");
		local sum2=$(sum "$2");
		if [ "$sum1" = "$sum2" ]; then
			echo "Existing ${src}($2) reused.";
			return 0;
		fi;
	fi;
	echo -n "copying ${src}(${!src})... ";
	cp -f "${!src}" "$2";
	chkerr;
	return 0;
}

chsuffix ()
{
	local var="$1";
	local fname=`basename "$2"`;
	local OIFS=${IFS};
	IFS='.';
	na=($fname);
	IFS=${OIFS};
	eval "${var}=${na[0]}.${3}";
}

pad_file_aligned ()
{
	local __file="$1";
	local __alignment="$2";
	local __padvalue="$3";
	local __padstring="";

	filesize=$(stat --format=%s "${__file}");
	rem=$(( filesize % __alignment ));
	if (( rem > 0 )); then
		rem=$(( __alignment - rem ));
		for ((i = 0 ; i < rem ; i++)); do
			__padstring+=${__padvalue};
		done;
		echo -e -n "${__padstring}" >> "${__file}";
	fi;
}

build_fsimg ()
{
	local __localsysfile="$1";
	local __fillpat="$2";
	local __rootfssize="$3";
	local __rootfs_type="$4";
	local __rootfs_dir="$5";
	local __cmdline="$6";
	local __do_sign="$7";
	local _extlinux_conf="extlinux/extlinux.conf"

	echo "Making ${__localsysfile}... ";

	local bcnt=$(( ${__rootfssize} / 512 ));
	local bcntdiv=$(( ${__rootfssize} % 512 ));
	if [ ${bcnt} -eq 0 -o ${bcntdiv} -ne 0 ]; then
		echo "Error: ${__rootfs_type} file system size has to be 512 bytes allign.";
		exit 1;
	fi
	if [ "${__rootfs_type}" != "FAT32" ] && [ ! -f "${__rootfs_dir}/boot/${_extlinux_conf}" ]; then
		echo "${__rootfs_dir}/boot/${_extlinux_conf} is not found, exiting...";
		exit 1
	fi
	if [ "${__fillpat}" != "" -a "${__fillpat}" != "0" ]; then
		local fc=`printf '%d' ${__fillpat}`;
		local fillc=`printf \\\\$(printf '%02o' $fc)`;
		< /dev/zero head -c ${__rootfssize} | tr '\000' ${fillc} > ${__localsysfile};
		chkerr "making ${__localsysfile} with fillpattern($fillc}) failed.";
	else
		truncate --size ${__rootfssize} ${__localsysfile};
		chkerr "making ${__localsysfile} with zero fillpattern failed.";
	fi;
	loop_dev="$(losetup --show -f "${__localsysfile}")";
	chkerr "mapping ${__localsysfile} to loop device failed.";
	if [ "${__rootfs_type}" = "FAT32" ]; then
		mkfs.msdos -I -F 32 "${loop_dev}" > /dev/null 2>&1;
	else
		mkfs -t ${__rootfs_type} "${loop_dev}" > /dev/null 2>&1;
	fi;
	chkerr "formating ${__rootfs_type} filesystem on ${__localsysfile} failed.";
	mkdir -p mnt;		chkerr "make $4 mount point failed.";
	mount "${loop_dev}" mnt;	chkerr "mount ${__localsysfile} failed.";
	mkdir -p mnt/boot/dtb;	chkerr "make ${__localsysfile}/boot/dtb failed.";
	cp -f "${kernel_fs}" mnt/boot;
	chkerr "Copying ${kernel_fs} failed.";
	_dtbfile=${__rootfs_dir}/boot/${dtbfilename};
	if [ -f "${_dtbfile}" ]; then
		cp -f "${_dtbfile}" "mnt/boot/dtb/${dtbfilename}";
		chkerr "populating ${_dtbfile} to ${__localsysfile}/boot/dtb failed.";
	fi;
	if [ "${__rootfs_type}" = "FAT32" ]; then
		touch -f mnt/boot/cmdline.txt > /dev/null 2&>1;
		chkerr "Creating cmdline.txt failed.";
		echo -n -e "${__cmdline}" >mnt/boot/cmdline.txt;
		chkerr "Writing cmdline.txt failed.";
	else
		pushd mnt > /dev/null 2>&1;
		echo -n -e "\tpopulating rootfs from ${__rootfs_dir} ... ";
		(cd "${__rootfs_dir}"; tar cf - *) | tar xf - ;
		chkerr "Failed. Your APPSIZE might be too small.";

		# Populate extlinux.conf if "$cmdline" exists
		if [ "${__cmdline}" != "" ]; then
			# Add the "$cmdline" at the APPEND line if it does not exist.
			echo -n -e "\tpopulating /boot/${_extlinux_conf} ... ";
			rootfs_found=$(grep -cE "${__cmdline}" "./boot/${_extlinux_conf}");
			if [ "${rootfs_found}" == "0" ];then
				sed -i "/^[ \t]*APPEND/s|\$| ${__cmdline}|" "./boot/${_extlinux_conf}";
				chkerr;
			fi;
		fi;
		if [ "${__do_sign}" = "True" ]; then
			local kernel_fs_basename;
			kernel_fs_basename=$(basename "${kernel_fs}");
			echo -n -e "\tgenerating sig file of ${kernel_fs_basename} ... ";
			signimage "./boot/${kernel_fs_basename}" "True" "kernel" "${minratchet_configname}"; chkerr;
			echo -n -e "\tgenerating sig file of ${dtbfilename} ... ";
			signimage "./boot/dtb/${dtbfilename}" "True" "kernel_dtb" "${minratchet_configname}"; chkerr;
			echo -n -e "\tgenerating sig file of initrd ... ";
			signimage "./boot/initrd" "True" "data"; chkerr;
			echo -n -e "\tgenerating sig file of extlinux.conf ... ";
			# Signing tool will pad extlinux.conf with 0x80 to be 16-byte aligned.
			# This pad byte of 0x80 may cause some utilities fail to read the entire
			# extlinux.conf.
			# So, pad extlinux.conf to 16-byte aligned with linefeed.
			pad_file_aligned "./boot/${_extlinux_conf}" 16 "\x0a";
			signimage "./boot/${_extlinux_conf}" "True" "data"; chkerr;
		fi
		popd > /dev/null 2>&1;
	fi;
	echo -e -n "\tSync'ing ${__localsysfile} ... ";
	sync; sync; sleep 5;	# Give FileBrowser time to terminate gracefully.
	echo "done.";
	umount "${loop_dev}" > /dev/null 2>&1;
	losetup -d "${loop_dev}" > /dev/null 2>&1;
	rmdir mnt > /dev/null 2>&1;

	if [ "${__fillpat}" != "" -a -x mksparse ]; then
		echo -e -n "\tConverting RAW image to Sparse image... ";
		mv -f ${__localsysfile} ${__localsysfile}.raw;
		if [ "${BLBlockSize}" != "" ]; then
			blblksizeoption="-b $BLBlockSize";
		fi;
		./mksparse ${blblksizeoption} --fillpattern=${__fillpat} ${__localsysfile}.raw ${__localsysfile}; chkerr;
	fi;
	echo "${__localsysfile} built successfully. ";
}

get_fuse_level ()
{
	local rcmcmd;
	local inst_args="";
	local idval_1="";
	local idval_2="";
	local flval="";
	local baval="None";
	local flvar="$1";
	local hivar="$2";
	local bavar="$3";

	if [ -f "${BL_DIR}/tegrarcm_v2" ]; then
		rcmcmd="tegrarcm_v2";
	elif [ -f "${BL_DIR}/tegrarcm" ]; then
		rcmcmd="tegrarcm";
	else
		echo "Error: tegrarcm is missing.";
		exit 1;
	fi;
	if [ -n "${usb_instance}" ]; then
		inst_args="--instance ${usb_instance}";
	fi;
	pushd "${BL_DIR}" > /dev/null 2>&1;
	ECID=$(./${rcmcmd} ${inst_args} --uid | grep BR_CID | cut -d' ' -f2);
	popd > /dev/null 2>&1;
	if [ "${ECID}" != "" ]; then
		idval_1="0x${ECID:3:2}";
		eval "${hivar}=\"${idval_1}\"";
		idval_2="0x${ECID:6:2}";

		flval="${ECID:2:1}";
		baval="";
		if [ "${idval_1}" = "0x21" -o "${idval_1}" = "0x12" -o \
			"${idval_1}" = "0x00" -a "${idval_2}" = "0x21" ]; then
			case ${flval} in
			0|1|2) flval="fuselevel_nofuse"; ;;
			3)     flval="fuselevel_production"; ;;
			4)     flval="fuselevel_production"; baval="NS"; ;;
			5)     flval="fuselevel_production"; baval="SBK"; ;;
			6)     flval="fuselevel_production"; baval="PKC"; ;;
			*)     flval="fuselevel_unknown"; ;;
			esac;
			SKIPUID="--skipuid";
			if [ "${idval_1}" = "0x00" ]; then
				eval "${hivar}=\"${idval_2}\"";
			fi;
		elif [ "${idval_1}" = "0x80" ]; then
			if [ "${idval_2}" = "0x19" ]; then
				case ${flval} in
				0|1|2) flval="fuselevel_nofuse"; ;;
				8)     flval="fuselevel_production"; baval="NS"; ;;
				# 9: 2K RSA, a: 3K RSA
				9|a)   flval="fuselevel_production"; baval="PKC"; ;;
				# d: 2K RSA + SBK, e: 3K RSA + SBK
				d|e)   flval="fuselevel_production"; baval="SBKPKC"; ;;
				esac;
				SKIPUID="--skipuid";
				hwchipid="0x19";
				hwchiprev="${ECID:5:1}";
			fi
		else
			case ${flval} in
			0|1|2) flval="fuselevel_nofuse"; ;;
			8|c)   flval="fuselevel_production"; baval="NS"; ;;
			9|d)   flval="fuselevel_production"; baval="SBK"; ;;
			a)     flval="fuselevel_production"; baval="PKC"; ;;
			e)     flval="fuselevel_production"; baval="SBKPKC"; ;;
			*)     flval="fuselevel_unknown"; ;;
			esac;
		fi;
		eval "${flvar}=\"${flval}\"";
		eval "${bavar}=\"${baval}\"";
	fi;
}

function get_full_path ()
{
	local val="$1";
	local result="$2";
	local fullpath;
	fullpath=$(readlink -f ${val});	# null if path is invalid
	if [ "${fullpath}" == "" ]; then
		echo "Invalid path/filename ${val}";
		exit 1;
	fi;
	eval "${result}=${fullpath}";
}

#
# XXX: This EEPROM read shall be replaced with new FAB agnostic function.
#
get_board_version ()
{
	local args="";
	local __board_id=$1;
	local __board_version=$2;
	local __board_sku=$3;
	local __board_revision=$4;
	local command="dump eeprom boardinfo cvm.bin"
	local boardid;
	local boardversion;
	local boardsku;
	local boardrevision;
	if [ -n "${usb_instance}" ]; then
		args+="--instance ${usb_instance} ";
	fi;
	if [ "${CHIPMAJOR}" != "" ]; then
		args+="--chip \"${CHIPID} ${CHIPMAJOR}\" ";
	else
		args+="--chip ${CHIPID} ";
	fi;
	args+="--applet \"${LDK_DIR}/${SOSFILE}\" ";
	args+="${SKIPUID} ";
	SKIPUID="";
	if [ "${CHIPID}" = "0x19" ]; then
		mkfilesoft soft_fuses     "${TARGET_DIR}/BCT/${SOFT_FUSES}";
		cp2local soft_fuses "${BL_DIR}/${soft_fusesname}";
		args+="--soft_fuses ${soft_fusesname} "
		args+="--bins \"mb2_applet ${MB2APPLET}\" ";
		command+=";reboot recovery"
	fi
	args+="--cmd \"${command}\" ";
	local cmd="./tegraflash.py ${args}";
	pushd "${BL_DIR}" > /dev/null 2>&1;
	if [ "${keyfile}" != "" ]; then
		cmd+="--key \"${keyfile}\" ";
	fi;
	if [ "${sbk_keyfile}" != "" ]; then
		cmd+="--encrypt_key \"${sbk_keyfile}\" ";
	fi;
	echo "${cmd}";
	eval "${cmd}";
	chkerr "Reading board information failed.";
	if [ "${SKIP_EEPROM_CHECK}" = "" ]; then
		boardid=`./chkbdinfo -i cvm.bin`;
		boardversion=`./chkbdinfo -f cvm.bin`;
		boardsku=`./chkbdinfo -k cvm.bin`;
		boardrevision=`./chkbdinfo -r cvm.bin`;
		chkerr "Parsing board information failed.";
	fi;
	popd > /dev/null 2>&1;
	eval ${__board_id}="${boardid}";
	eval ${__board_version}="${boardversion}";
	eval ${__board_sku}="${boardsku}";
	eval ${__board_revision}="${boardrevision}";
}

#
# EEPROM get board S/N .
#
boardinfo_trk ()
{
	local boardinforom;
	local boardpartnu;
	if [[ -e "${LDK_DIR}/nv_internal_trk.sh" &&
		-e "${BL_DIR}/chkbdinfo" &&
		-e "${BL_DIR}/cvm.bin" ]]; then
		pushd "${BL_DIR}" > /dev/null 2>&1;
		boardinforom=$(./chkbdinfo -a cvm.bin);
		boardpartnu=$(./chkbdinfo -p cvm.bin);
		if [[ "${boardinforom}" != "" ]] && [[ "${boardpartnu}" != "" ]]; then
			eval "PRODUCT_OUT=\"${LDK_DIR}\" \"${LDK_DIR}/nv_internal_trk.sh\" \"${boardinforom}\" \"${boardpartnu}\"";
		fi
		popd > /dev/null 2>&1;
	fi
}

#
# SoC Sanity Check:
#
chk_soc_sanity ()
{
	local mach_dir="";
	local socname="Unknown";
	local opmode="Unknown";
	local disk_enc="";

	if [ "${hwchipid}" = "" ]; then
		# Nothing to check against. Just let it go.
		echo "Error: probing the target board failed.";
		echo "       Make sure the target board is connected through ";
		echo "       USB port and is in recovery mode.";
		exit 1;
	fi;

	#
	# Print Target Board Information:
	# NOTE: The list of board listed here may or may not be
	#	supported by the version of BSP(Board Support Package)
	#	that provides this copy of the script. This lists all
	#	of the publicly available Jetson developer platforms.
	#
	case ${hwchipid} in
	0x21) socname="Tegra 210"; mach_dir="t210ref"; ;;
	0x18) socname="Tegra 186"; mach_dir="t186ref"; ;;
	0x19) socname="Tegra 194"; mach_dir="t186ref"; ;;
	esac;

	case ${fuselevel} in
	fuselevel_nofuse) opmode="pre-production"; ;;
	fuselevel_production) opmode="production"; ;;
	esac;

	if [ ${disk_enc_enable} -eq 1 ]; then
		disk_enc="enabled";
	else
		disk_enc="disabled";
	fi;

	echo	"# Target Board Information:";
	echo -n "# Name: ${ext_target_board}, Board Family: ${target_board}, ";
	echo	"SoC: ${socname}, ";
	echo	"# OpMode: ${opmode}, Boot Authentication: ${bootauth}, ";
	echo	"# Disk encryption: ${disk_enc} ,";
	echo	"${INFODIVIDER}";

	if [ "${CHIPID}" != "" -a "${CHIPID}" != "${hwchipid}" ]; then
		echo -n "Error: The Actual SoC ID(${hwchipid}) ";
		echo -n "mismatches intended ${ext_target_board} ";
		echo "SoC ID(${CHIPID}).";
		exit 1;
	fi;

	if [ "${target_board}" != "${mach_dir}" ]; then
		echo -n "Error: The Actual board family (${mach_dir}) ";
		echo -n "mismatches intended ${ext_target_board} ";
		echo "board family(${target_board}).";
		exit 1;
	fi;

	case ${bootauth} in
	PKC)
		if [ "${keyfile}" = "" ] || [ "${sbk_keyfile}" != "" ]; then
			echo -n "Error: Either RSA key file is not provided or SBK key ";
			echo "file is provided for PKC protected target board.";
			exit 1;
		fi;
		;;
	SBKPKC)
		if [ "${keyfile}" = "" ] || [ "${sbk_keyfile}" = "" ]; then
			echo -n "Error: Either RSA key file and/or SBK key file ";
			echo "is not provided for SBK and PKC protected target board.";
			exit 1;
		fi;
		;;
	SBK)
		echo "Error: L4T does not support SBK protected target board.";
		exit 1;
		;;
	NS)
		if [ "${keyfile}" != "" ] || [ "${sbk_keyfile}" != "" ]; then
			echo -n "Error: either RSA key file and/or SBK key file ";
			echo "are provided for none SBK and PKC protected target board.";
			exit 1;
		fi;
		;;
	*)
		if [ "${dbmaster}" != "" ]; then
			echo -n "Error: The RSA key file is provided for ";
			echo "non-PKC protected target board.";
			exit 1;
		fi;
		;;
	esac;
}

function rootuuid_gen() {
	local root_id=$1
	local uuid=""
	local uuidgen_installed="$(which uuidgen || true)"

	if [ "${uuidgen_installed}" == "" ]; then
		echo "Error: uuidgen not installed! Please provide the UUID or install"
		echo "uuidgen. For example, to install uuidgen for Ubuntu distributions,"
		echo "execute the command 'sudo apt install uuid-runtime'. Otherwise a"
		echo "UUID can be provided by storing a UUID to the file"
		echo "${rootfsuuidfile} or ${rootfsuuidfile}_b if neabled ROOTFS_AB"
		usage allunknown 1;
	fi

	uuid="$(uuidgen)"
	setval "rootfsuuid${root_id}" uuid;

	echo "${uuid}" > "${rootfsuuidfile}${root_id}"
	echo "Generated UUID ${uuid} for mounting root APP${root_id} partition."
}

function rootuuid_chk_and_gen() {
	local root_id=$1
	local uuid=""
	local uuid_regex="([0-9a-f]{8}-[0-9a-f]{4}-[0-9a-f]{4}-[0-9a-f]{4}-[0-9a-f]{12})"

	# For external device, if you want to generate a new uuid every time you flash,
	# uncomment the below lines
	# if [ "${external_device}" = "1" ] && [ -f "${rootfsuuidfile}${root_id}" ]; then
	# 	rm "${rootfsuuidfile}${root_id}"
	# fi

	# read UUID which stored in the file ${rootfsuuidfile} if the file exist
	if [ -f "${rootfsuuidfile}${root_id}" ]; then
		uuid="$(sed -nr "s/^${uuid_regex}$/\1/p" "${rootfsuuidfile}${root_id}")"

		if [ "${#uuid}" != "36" ]; then
			echo "File ${rootfsuuidfile}${root_id} contains invalid UUID!"
			usage allunknown 1;
		fi

		setval "rootfsuuid${root_id}" uuid;
		echo "Using UUID ${uuid} for mounting root APP${root_id} partition."
	fi

	# generate UUID if ${rootfsuuidfile} isn't present
	eval uuid='$'{"rootfsuuid${root_id}"}
	if [ "${uuid}" == "" ] && [ "${target_partname}" == "" ]; then
		rootuuid_gen "${root_id}"
	fi
}

function rootuuid_restore {
	local ext="${1}"
	local _rootfsuuid="rootfsuuid${ext}"
	local _rootfsuuid_b

	rootuuid_chk_and_gen "${ext}"

	if [[ "${rootfs_ab}" == 1 ]]; then
		# get UUID for APP_b
		_rootfsuuid_b="rootfsuuid_b${ext}"
		rootuuid_chk_and_gen "_b${ext}"
	fi



	if [[ "${!_rootfsuuid}" == "" ]] || \
	   [[ "${rootfs_ab}" == 1 && "${!_rootfsuuid_b}" == "" ]]; then
		echo "No UUID found for root partition! If the root partition"
		echo "is not currently being mounted using a partition UUID,"
		echo "then flash the device by specifying the root device that"
		echo "was specified when previously flashing the entire system"
		echo "(eg. /dev/mmcblk0p1). Otherwise, to mount the root"
		echo "partition using a partition UUID please either:"
		echo "1. If you know the UUID for the root partition save it"
		echo "   to the file ${rootfsuuidfile},"
		echo "   or for root B partition save it"
		echo "   to the file  ${rootfsuuidfile}_b"
		echo "2. Re-flash entire system to generate a new UUID."
		usage allunknown 1;
	fi
}

function sysfile_exist {
	if [ ${disk_enc_enable} -eq 0 ]; then
		echo "Reusing existing ${localsysfile}... ";
		if [ ! -e "${localsysfile}" ]; then
			echo "file does not exist.";
			exit 1;
		fi;
		if [[ "${rootfs_ab}" == 1 ]]; then
			echo "Reusing existing ${localsysfile}.b... ";
			if [ ! -e "${localsysfile}_b" ]; then
				echo "file does not exist.";
				exit 1;
			fi;
		fi;
	else
		echo "Reusing existing ${localsysbootfile} & ${localsysencrootfile}... ";
		if [ ! -e "${localsysbootfile}" ] || [ ! -e "${localsysencrootfile}" ]; then
			echo "file does not exist.";
			exit 1;
		fi;
		if [[ "${rootfs_ab}" == 1 ]]; then
			echo "Reusing existing ${localsysbootfile_b} & ${localsysencrootfile_b}... ";
			if [ ! -e "${localsysbootfile_b}" ] || [ ! -e "${localsysencrootfile_b}" ]; then
				echo "file does not exist.";
				exit 1;
			fi;
		fi;
	fi;
	echo "done.";
}

function make_boot_image() {
	if [ -n "${BOOTIMG}" ]; then
		if ! [ -f "${BOOTIMG}" ]; then
			echo "Error: ${BOOTIMG} not found"
			exit 1;
		fi
		cp "${BOOTIMG}" "${localbootfile}"
		if [[ "${rootfs_ab}" == 1 ]]; then
			cp "${BOOTIMG}" "${localbootfile}_b"
		fi
		return
	fi
	echo -n "Making Boot image... ";
	./mkbootimg \
		--kernel "${kernel_image}" \
		--ramdisk "${ramdisk}" \
		--board "${target_rootdev}" \
		--output "${localbootfile}" \
		--cmdline "${cmdline}" > /dev/null 2>&1;
	chkerr;
	if [[ "${rootfs_ab}" == 1 ]]; then
		if [[ "${disk_enc_enable}" == 1 ]]; then
			./mkbootimg \
				--kernel "${kernel_image}" \
				--ramdisk "${ramdisk_b}" \
				--board "${target_rootdev}" \
				--output "${localbootfile}_b" \
				--cmdline "${cmdline_b}" > /dev/null 2>&1;
			chkerr;
		else
			./mkbootimg \
				--kernel "${kernel_image}" \
				--ramdisk "${ramdisk}" \
				--board "${target_rootdev}" \
				--output "${localbootfile}_b" \
				--cmdline "${cmdline_b}" > /dev/null 2>&1;
			chkerr;
		fi
	fi
}

function check_xmllint() {
	# Usage:
	#	check_xmllint {__ret_value}
	local __ret_value="${1}"

	if [ -f "/usr/bin/xmllint" ]; then
		eval "${__ret_value}=\"/usr/bin/xmllint\""
	else
		if [ -z "${__XMLLINT_BIN}" ]; then
			echo "ERROR xmllint not found! To install - please run: " \
				"\"sudo apt-get install libxml2-utils\""
			exit 1
		fi;
	fi;
}

function get_value_from_PT_table() {
	# Usage:
	#	get_value_from_PT_table {__pt_name} \
	#	{__pt_node} \
	#	{__pt_file} \
	#	{__ret_value}
	local __XMLLINT_BIN="";
	local __pt_name="${1}";
	local __pt_node="${2}";
	local __pt_file="${3}";
	local __ret_value="${4}";
	local __node_val="";

	# Check xmllint
	check_xmllint __XMLLINT_BIN

	# Get node value
	__node_val="$(${__XMLLINT_BIN} --xpath "/partition_layout/device/partition[@name='${__pt_name}']/${__pt_node}/text()" ${__pt_file})";
	__node_val=$(echo ${__node_val} | sed -e 's/^[[:space:]]*//');

	eval "${__ret_value}=\"${__node_val}\"";
}

function partition_exists_in_PT_table() {
	# Usage:
	#	partition_exists_in_PT_table {__pt_name} {__pt_file}
	local __XMLLINT_BIN="";
	local __pt_name="${1}";
	local __pt_file="${2}";

	# Check xmllint
	check_xmllint __XMLLINT_BIN

	# Check whether node exists
	${__XMLLINT_BIN} --xpath "/partition_layout/device/partition[@name='${__pt_name}']" ${__pt_file} >/dev/null 2>&1
	return $?
}

#
# Get attribuate from partition table
#
function get_attr_from_PT_table() {
	# Usage:
	#	get_attr_from_PT_table {__pt_name} \
	#	{__pt_attr} \
	#	{__pt_file} \
	#	{__ret_value}
	local __XMLLINT_BIN="";
	local __pt_name="${1}";
	local __pt_attr="${2}";
	local __pt_file="${3}";
	local __ret_value="${4}";
	local __attr_val="";

	# Check xmllint
	if [ -f "/usr/bin/xmllint" ]; then
		__XMLLINT_BIN="/usr/bin/xmllint";
	else
		if [ -z "${__XMLLINT_BIN}" ]; then
			echo "ERROR xmllint not found! To install - please run: " \
				"\"sudo apt-get install libxml2-utils\""
			exit 1
		fi;
	fi;

	# Get attr value
	__attr_val="$(${__XMLLINT_BIN} --xpath "string(/partition_layout/device/partition[@name='${__pt_name}']/@${__pt_attr})" "${__pt_file}")";

	eval "${__ret_value}=\"${__attr_val}\"";
}

function create_fsimg {
	local do_sign="${2}";

	if [ ${disk_enc_enable} -eq 0 ]; then
		local source_folder="${1}"
		APP_TAG+="-e s/APPFILE/${localsysfile}/ ";
		# this is set at a setval function
		if [ "${target_partname}" = "" ] || [ "${target_partname}" = "APP" ]; then
			build_fsimg "${localsysfile}" "${fillpat}" \
				    "${rootfssize}" "${rootfs_type}" \
				    "${source_folder}" "${cmdline}" "${do_sign}";
		fi;

		if [[ "${rootfs_ab}" == 1 ]]; then
			# build fsimage for APP_b
			local sysfile=""

			# check if APP_b exist in layout file
			get_value_from_PT_table "APP_b" "filename" "${cfgfile}" sysfile
			if [ "${sysfile}" != "" ]; then
				if [ "${target_partname}" = "" ] || \
				   [ "${target_partname}" = "APP_b" ]; then
					build_fsimg "${localsysfile}_b" "${fillpat}" \
						    "${rootfssize}" "${rootfs_type}" \
						    "${source_folder}" "${cmdline_b}" "${do_sign}";
				fi;
			fi;
		fi;
	else
		if [ "${target_partname}" = "" ] || [ "${target_partname}" = "APP" ]; then
			build_boot_fsimg "${localsysbootfile}" "${fillpat}" \
					 "${bootfssize}" "${rootfs_type}" \
					 "${rootfs_dir}/boot" "${cmdline}" "${do_sign}";
		fi;
		if [ "${target_partname}" = "" ] || [ "${target_partname}" = "APP_ENC" ]; then
			build_enc_root_fsimg "${localsysencrootfile}" "${fillpat}" \
					     "${encrootfssize}" "${rootfs_type}" \
					     "${rootfs_dir}" "${rootfsuuid_enc}" \
					     "${bootpartuuid}" "${ECID}";
		fi;

		if [[ "${rootfs_ab}" == 1 ]]; then
			if [ "${target_partname}" = "" ] || [ "${target_partname}" = "APP_b" ]; then
				echo -e -n "\tpopulating initrd_b to rootfs... ";
				cp -f initrd_b "${rootfs_dir}/boot/initrd"; chkerr;
				build_boot_fsimg "${localsysbootfile_b}" "${fillpat}" \
						 "${bootfssize}" "${rootfs_type}" \
						 "${rootfs_dir}/boot" "${cmdline_b}" "${do_sign}";
			fi;
			if [ "${target_partname}" = "" ] || [ "${target_partname}" = "APP_ENC_b" ]; then
				build_enc_root_fsimg "${localsysencrootfile_b}" "${fillpat}" \
						     "${encrootfssize}" "${rootfs_type}" \
						     "${rootfs_dir}" "${rootfsuuid_b_enc}" \
						     "${bootpartuuid_b}" "${ECID}";
			fi;
		fi;
	fi;
}

function signimage() {
	# l4t_sign_image.sh generates signature file (with .sig extension)
	# in the same folder of file path specified in --file
	local image="$1";
	local split="$2";
	local ftype="$3";
	local ratchet_config="$4";
	if [ -n "${ratchet_config}" ]; then
		cp -f "${BL_DIR}"/"${ratchet_config}" .
		"${LDK_DIR}"/l4t_sign_image.sh \
			--file "$image" --type "$ftype" \
			--key "${keyfile}" --encrypt_key "${user_keyfile}" --chip "${tegraid}" --split "${split}" \
			--minratchet_config "${ratchet_config}";
	else
		"${LDK_DIR}"/l4t_sign_image.sh \
			--file "$image" --type "$ftype" \
			--key "${keyfile}" --encrypt_key "${user_keyfile}" --chip "${tegraid}" --split "${split}";
	fi;
	chkerr;
}

function assign_string() {
	# Usage:
	#	assign_string {filename} \
	#	{string} 	# string to assign \
	#	{offset} 	# offset in decimal \
	#	{size}		# number of chars to assign
	local filename="${1}";
	local string="${2}";
	local offset="${3}";
	local size="${4}";

	echo "assign_string: ${filename} ${string} ${offset} ${size}"

	# example dd comand: echo ${string} | dd of=foo bs=1 seek=131064 count=4 conv=notrunc
	dd_cmd="echo ${string} "
	dd_cmd+="| dd of=${filename} bs=1 seek=${offset} count=${size} conv=notrunc"
	echo "${dd_cmd}"
	eval "${dd_cmd}"
}

function assign_value() {
	# Usage:
	#	assign_value {filename} \
	#	{value} 	# value in decimal to assign \
	#	{offset} 	# offset in decimal \
	#	{size}		# number of bytes to assign
	local filename="${1}";
	local value="${2}";
	local offset="${3}";
	local size="${4}";

	echo "assign_value: ${filename} ${value} ${offset} ${size}"

	# example dd comand: printf '\xab\xcd\xef\x65' | dd of=foo bs=1 seek=131068 count=4 conv=notrunc
	# printf '\x09\x38\xc5\x33' | dd of=crc-flash.xml.bin bs=1 seek=131068 count=4 conv=notrunc
	# value is in little-endian
	dd_cmd="printf '"
	for ((i = 0 ; i < size ; i++)); do
		byte=$(( value & 0xff ))
		value=$(( value >> 8 ))
		dd_cmd+="\x"
		dd_cmd+=$( printf "%x" ${byte} )
	done;
	dd_cmd+="' | dd of=${filename} bs=1 seek=${offset} count=${size} conv=notrunc"
	echo "${dd_cmd}"
	eval "${dd_cmd}"
}

# function: generate_pt_header
#
# This function generates pt header and stores the pt header to the end of
# the PT partition.

# flash.xml.bin contains the partition table, and is flashed to PT partition.
# So the size of flash.xml.bin will be expanded to the size of PT partition.
#
# The pt header consists of :
#    o version (2 bytes):
#      * major = 0x01
#      * minor = 0x00
#    o reserved (6 bytes)
#    o magic (4 bytes) = 'PTHD'
#    o crc32 (4 bytes)
#
# The flash.xml.bin is created later during the actual flashing procedures
# by tegraparser.
#
# So flash.xml.bin cannot be created here (will be overwritten by tegraparser).
# Use new name of "crc-flash.xml.bin for this reason, and populate the new name
# to crc-flash.xml and flash.xml too.
#
# Notes: ${localcfgfile}=flash.xml
#        These procedures assume that the ptfile (filename spcecified in PT partition)
#        is ${localcfgfile}.bin (or flash.xml.bin)
#
function generate_pt_header()
{
	ptfile=""
	ptsize=""

	PT_VER_MAJOR=$((0x01))
	PT_VER_MINOR=$((0x00))
	PT_MAGIC='PTHD'

	get_value_from_PT_table "PT" "filename" "${localcfgfile}" ptfile
	get_value_from_PT_table "PT" "size" "${localcfgfile}" ptsize
	# use a new name of crc-flash.xml.tmp
	cp "${localcfgfile}" crc-"${localcfgfile}".tmp
	# replace old flash.xml.bin with new crc-flash.xml.bin
	sed -i -e "s/${ptfile}/crc-${ptfile}/" crc-"${localcfgfile}".tmp
	# call tegraparser, it will generate crc-flash.xml.bin
	./tegraparser --pt crc-"${localcfgfile}".tmp
	# copy the new crc-${localcfgfile}.tmp to ${localcfgfile}
	cp crc-"${localcfgfile}".tmp "${localcfgfile}"

	# expand the file to the PT partition size
	truncate -s "${ptsize}" "crc-${ptfile}"

	offset=$((ptsize-16))
	assign_value "crc-${ptfile}" ${PT_VER_MAJOR} $offset 1

	offset=$((ptsize-15))
	assign_value "crc-${ptfile}" ${PT_VER_MINOR} $offset 1

	offset=$((ptsize-8))
	assign_string "crc-${ptfile}" ${PT_MAGIC} $offset 4

	# call tegrahost to fill crc32 to the last 4 bytes of crc-${ptfile}
	./tegrahost --fillcrc32 "crc-${ptfile}"
}

if [ $# -lt 2 ]; then
	usage allunknown 1;
fi;

nargs=$#;
target_rootdev=${!nargs};
nargs=$(($nargs-1));
ext_target_board=${!nargs};

# NV internal
_nvbrd_trk=0

if [ ! -r ${ext_target_board}.conf ]; then
	echo "Error: Invalid target board - ${ext_target_board}.";
	usage allunknown 1;
fi

# set up LDK_DIR path
LDK_DIR=$(cd "$(dirname "$0")" && pwd);
LDK_DIR=$(readlink -f "${LDK_DIR}");

# set common print message for process_board_version()
print_board_version()
{
	local board_id="${1}";
	local board_version="${2}";
	local board_sku="${3}";
	local board_revision="${4}";
	local chiprev="${5}";

	echo "Board ID(${board_id}) version(${board_version}) sku(${board_sku}) revision(${board_revision})" >/dev/stderr;
}

ext_target_board_canonical=`readlink -e "${ext_target_board}".conf`
ext_target_board_canonical=`basename "${ext_target_board_canonical}" .conf`
disk_enc_enable=0;
rootfs_ab=0;
source ${ext_target_board}.conf

# set up path variables
BL_DIR="${LDK_DIR}/bootloader";
TARGET_DIR="${BL_DIR}/${target_board}";
KERNEL_DIR="${LDK_DIR}/kernel";
export PATH="${KERNEL_DIR}:${PATH}";		# preference on our DTC
DTB_DIR="${KERNEL_DIR}/dtb";
DTC="${KERNEL_DIR}/dtc";
if [ "${BINSARGS}" = "" -a "${BINS}" != "" ]; then			#COMPAT
	BINARGS="--bins \"";						#COMPAT
fi;									#COMPAT
if [ "${BINSARGS}" != "" ]; then
	SKIPUID="--skipuid";
fi;

# Print BSP Info:
#
echo "${INFODIVIDER}";
echo "# L4T BSP Information:";
if [ -f "${LDK_DIR}/nv_tegra/bsp_version" ]; then
	source "${LDK_DIR}/nv_tegra/bsp_version"
	echo "# R${BSP_BRANCH} , REVISION: ${BSP_MAJOR}.${BSP_MINOR}"
elif [ -f "${LDK_DIR}/rootfs/etc/nv_tegra_release" ]; then
	head -n1 "${LDK_DIR}/rootfs/etc/nv_tegra_release" | \
		sed -e s/DATE:/\\n\#\ DATE:/;
else
	echo "# Unknown Release";
fi;
echo "${INFODIVIDER}";

# Determine rootdev_type
#
rootdev_type="external";
if [[ "${target_rootdev}" == "internal" || "${target_rootdev}" == mmcblk0p* || \
      "${target_rootdev}" == ${BOOTDEV} ]]; then
	rootdev_type="internal";
	INITRD="";
	if [ ${disk_enc_enable} -eq 1 ] && [ "${target_rootdev}" != "internal" ]; then
		echo "Change device boot from ${target_rootdev} to internal"
		target_rootdev="internal";
	fi
elif [ "${target_rootdev}" = "eth0" -o "${target_rootdev}" = "eth1" ]; then
	rootdev_type="network";
	disk_enc_enable=0;
elif [[ "${target_rootdev}" != "external" && "${target_rootdev}" != mmcblk1p* && \
	"${target_rootdev}" != sd* && "${target_rootdev}" != nvme* ]]; then
	echo "Error: Invalid target rootdev($target_rootdev).";
	usage rootdevunknown 1;
fi;

if [[ "${rootdev_type}" == "external" && "${disk_enc_enable}" -eq 1 ]]; then
	echo "Error: When disk encryption is enabled, root device cannot be ${target_rootdev}"
	exit 1;
fi;

# Import disk encryption helper function
#
if [ ${disk_enc_enable} -eq 1 ]; then
	disk_encryption_helper_dir="${LDK_DIR}/tools/disk_encryption";
	if [ ! -f "${disk_encryption_helper_dir}/disk_encryption_helper.func" ]; then
		echo "Error: disk encryption is not supported."
		exit 1
	fi
	source "${disk_encryption_helper_dir}/disk_encryption_helper.func"
fi;

rootfsuuid="";
rootfsuuid_enc="";
rootfsuuid_ext="";
rootfsuuid_ext_enc="";
rootfsuuid_b="";
rootfsuuid_b_enc="";
rootfsuuid_b_ext=""
rootfsuuid_b_ext_enc="";
cmdline_b="";

rootfsuuidfile="${BL_DIR}/l4t-rootfs-uuid.txt"
read_part_name="";
rcm_boot=0;
no_root_check=0;
no_flash=0;
rapid_boot=0
external_device=0;
no_systemimg=0;
bup_blob=0;
to_sign=0;
support_multi_spec=0;
clean_up=0;
PKCKEY="";
_ODMDATA="";
opstr+="b:c:d:e:f:h:i:k:m:n:o:p:rs:t:u:v:w:x:y:z:B:C:F:G:I:K:L:M:N:P:R:S:Z:-:";
while getopts "${opstr}" OPTION; do
	case $OPTION in
	b) BCTFILE=${OPTARG}; ;;
	c) CFGFILE=${OPTARG}; ;;
	d) DTBFILE=${OPTARG}; ;;
	e) EMMCSIZE=${OPTARG}; ;;
	f) FLASHAPP=${OPTARG}; ;;
	h) usage allunknown 0; ;;
	i) ENC_RFS_KEY=${OPTARG}; ;;
	k) target_partname=${OPTARG}; ;;	# cmdline only
	m) MTSPREBOOT=${OPTARG}; ;;
	n) NFSARGS=${OPTARG}; ;;
	o) _ODMDATA=${OPTARG}; ;;
	p) BOOTPARTSIZE=${OPTARG}; ;;
	r) reuse_systemimg="true"; ;;		# cmdline only
	s) PKCKEY=${OPTARG}; ;;
	t) TEGRABOOT=${OPTARG}; ;;
	u) dbmaster="${OPTARG}"; ;;
	v) SBKKEY=${OPTARG}; ;;
	w) WB0BOOT=${OPTARG}; ;;
	x) tegraid=${OPTARG}; ;;
	y) fusetype=${OPTARG}; ;;
	z) sn=${OPTARG}; ;;
	B) BOARDID=${OPTARG}; ;;
	C) CMDLINE="${OPTARG}"; ;;
	F) FLASHER=${OPTARG}; ;;
	G) read_part_name=${OPTARG}; ;;
	I) INITRD=${OPTARG}; ;;
	K) KERNEL_IMAGE=${OPTARG}; ;;
	L) BOOTLOADER=${OPTARG}; ;;
	M) MTS=${OPTARG}; ;;
	N) NFSROOT=${OPTARG}; ;;
	P) BOOTPARTLIMIT=${OPTARG}; ;;
	R) ROOTFS_DIR=${OPTARG}; ;;
	S) ROOTFSSIZE=${OPTARG}; ;;
	Z) zflag="true"; ;;			# cmdline only
	-) case ${OPTARG} in
	   no-root-check) no_root_check=1; ;;
	   no-flash) no_flash=1; ;;
	   no-systemimg) no_systemimg=1; ;;
	   external-device) external_device=1; ;;
	   rcm-boot) rcm_boot=1; ;;
	   bup) bup_blob=1; ;;
	   sign) to_sign=1; ;;
	   multi-spec) support_multi_spec=1; ;;
	   clean-up) clean_up=1; ;;
	   rapid-boot) rapid_boot=1; ;;
	   usb-instance)
		usb_instance="${!OPTIND}";
		OPTIND=$(($OPTIND + 1));
		;;
	   image)
		write_image_name="${!OPTIND}";
		OPTIND=$(($OPTIND + 1));
		;;
	   user_key)
		USERKEY="${!OPTIND}";
		OPTIND=$(($OPTIND + 1));
		;;
	   esac;;
	*) usage allunknown 1; ;;
	esac;
done

if [[ "${BUILD_SD_IMAGE}" == 1 && "${no_flash}" == 0 ]]; then
	echo "*** The option BUILD_SD_IMAGE must work with --no-flash flag. ***"
	echo "Exiting now...";
	exit 1;
fi;

# allow payload generation to happen without sudo option
if [ ${bup_blob} -eq 0 ]; then
	# if the user is not root, there is not point in going forward unless
	# the user knows what he's doing.
	if [ "${no_root_check}" != "1" ] && [ "${USER}" != "root" ]; then
		echo "flash.sh requires root privilege";
		exit 1;
	fi
fi

#
# -s option is obsolete and is repleced by -u option.
# However, to be compatible with earlier release, -s should still be handled
#
#  If -u is present, simply ignore -s
#  If -u is absent, assign value from -s to -u
#
if [ "${PKCKEY}" != "" ] && [ "${dbmaster}" = "" ]; then
	dbmaster="${PKCKEY}";
fi;

# get key file if -u option provided
keyfile="";
if [ "${dbmaster}" != "" ]; then
	if [[ ${dbmaster} =~ ^/ ]]; then
		keyfile="${dbmaster}";
	else
		keyfile=`readlink -f "${dbmaster}"`;
	fi;
	if [ ! -f "${keyfile}" ]; then
		echo "Error: keyfile ${keyfile} not found";
		exit 1;
	fi;
fi;

# get sbk key file if -v option provided
sbk_keyfile="";
if [ "${SBKKEY}" != "" ]; then
	# when sbk key is present, pkc key must be present
	if [ "${keyfile}" = "" ]; then
		echo "Error: missing PKC key; try -u";
		exit 1;
	fi;

	sbk_keyfile=`readlink -f "${SBKKEY}"`;
	if [ ! -f "${sbk_keyfile}" ]; then
		echo "Error: keyfile ${sbk_keyfile} not found";
		exit 1;
	fi;
fi;

# get user_key file if --user_key option provided
user_keyfile="";
zero_keyfile=".zero_.key";
if [ "${USERKEY}" != "" ]; then
	# when user key is present, sbk key must be present
	if [ "${sbk_keyfile}" = "" ]; then
		echo "Error: missing SBK key; try -v";
		exit 1;
	fi;

	user_keyfile=`readlink -f "${USERKEY}"`;
	if [ ! -f "${user_keyfile}" ]; then
		echo "Error: keyfile ${user_keyfile} not found";
		exit 1;
	fi;
else
	if [ "${sbk_keyfile}" != "" ]; then
		# there is sbk_key, but no user_key
		echo "sbk_keyfile is present, but no user_keyfile; set user_keyfile to zero keyfile";
		echo "0x00000000 0x00000000 0x00000000 0x00000000" > "${zero_keyfile}";
		user_keyfile=$(readlink -f "${zero_keyfile}");
	fi;
fi;

# get enc rfs key file if -i option provided
enc_rfs_keyfile="";
if [ "${ENC_RFS_KEY}" != "" ]; then
	enc_rfs_keyfile=$(readlink -f "${ENC_RFS_KEY}");
	if [ ! -f "${enc_rfs_keyfile}" ]; then
		echo "Error: keyfile ${enc_rfs_keyfile} not found";
		exit 1;
	fi;
fi;

ECID="";
# get the fuse level and update the data accordingly
fuselevel="${FUSELEVEL}";
hwchipid="";
hwchiprev="${CHIPREV}";
if [ "${hwchiprev}" = "" ]; then
	if [ "${CHIPID}" = "0x19" ]; then
		hwchiprev="2";
	else
		hwchiprev="0";
	fi
fi;
bootauth="";
if [ "${fuselevel}" = "" ]; then
	get_fuse_level fuselevel hwchipid bootauth;
	# fuselevel_unknown or empty will be handled as fuselevel_production
	if [ "${fuselevel}" = "fuselevel_unknown" ] || [ "${fuselevel}" = "" ]; then
		fuselevel="fuselevel_production";
	fi;
else
	# can not "--skipuid" when function get_fuse_level is skipped.
	SKIPUID="";
fi;

declare -F -f process_fuse_level > /dev/null 2>&1;
if [ $? -eq 0 ]; then
	process_fuse_level "${fuselevel}";
fi;

#
# Handle -G option for reading partition image to file
#
if [ "${read_part_name}" != "" ]; then
	# Exit if no -k option
	if [ "${target_partname}" = "" ]; then
		echo "Error: missing -k option to specify partition name";
		exit 1;
	fi
	# Exit if --image option is provided for write partition
	if [ "${write_image_name}" != "" ]; then
		echo "Error: not support to write partition while reading partition";
		exit 1;
	fi
	# Exit if path is invalid
	get_full_path ${read_part_name} read_part_name;
fi;

#
# Handle --image option for writing image to specified partition
#
if [ "${write_image_name}" != "" ]; then
	# Exit if no -k option
	if [ "${target_partname}" = "" ]; then
		echo "Error: missing -k option to specify partition name";
		exit 1;
	fi
	# Exit if file does not exist
	if [ ! -f "${write_image_name}" ]; then
		echo "Error: ${write_image_name} does not exist";
		exit 1;
	fi;
	# Exit if path is invalid
	get_full_path ${write_image_name} write_image_name;
fi;

# SoC Sanity Check
if [ ${no_flash} -eq 0 ]; then
	chk_soc_sanity;
fi;

if [ ${rapid_boot} -ne 0 ]; then
	declare -F -f rapid_boot_functionality > /dev/null 2>&1;
	rapid_boot_functionality;
fi;

# get the board version and update the data accordingly
declare -F -f process_board_version > /dev/null 2>&1;
if [ $? -eq 0 ]; then
	board_version="${FAB}";
	board_id="${BOARDID}";
	board_sku="${BOARDSKU}";
	board_revision="${BOARDREV}";
	if [ "${board_version}" == "" ]; then
		if [ "${hwchipid}" != "" ]; then
			get_board_version board_id board_version board_sku board_revision;
			_nvbrd_trk=1;
			BOARDID="${board_id}";
			BOARDSKU="${board_sku}";
			FAB="${board_version}";
			BOARDREV="${board_revision}";
		fi;
	fi;
	process_board_version "${board_id}" "${board_version}" "${board_sku}" "${board_revision}" "${hwchiprev}";
fi;

# convert fuselevel to digit string
if [ "${fuselevel}" == "fuselevel_nofuse" ]; then
	fuselevel_s="0";
else
	fuselevel_s="1";
fi;

# Set board spec: BOARD_ID-FAB-BOARDSKU-BOARDREV-NV_PRODUCTION-CHIP_REV-BOARD_NAME-ROOTFS_DEV
spec="${BOARDID}-${FAB}-${BOARDSKU}-${BOARDREV}-${fuselevel_s}-${hwchiprev}-${ext_target_board}-${target_rootdev}";
# Make sure spec length is less than maximum supported by BUP (64)
MAX_SPEC_LEN=64
if ((${#spec} > ${MAX_SPEC_LEN})); then
	echo "Error: spec length exceeds ${MAX_SPEC_LEN}, ${spec}(len=${#spec})"
	exit 1
fi;

# get board SN and Part
if [ ${_nvbrd_trk} -ne 0 ]; then
	timeout 10s cat <(boardinfo_trk);
fi;

###########################################################################
# System default values: should be defined AFTER target_board value.
#
ROOTFS_TYPE="${ROOTFS_TYPE:-ext4}";
DEVSECTSIZE="${DEVSECTSIZE:-512}";		# default sector size = 512
BOOTPARTLIMIT="${BOOTPARTLIMIT:-10485760}";	# 1MiB limit
ACR_TYPE="${ACR_TYPE:-acr-debug}";		# default is acr-debug
fillpat="${FSFILLPATTERN:-0}";			# no cmdline: default=0
no_rootfs="${NO_ROOTFS:-0}" 			# default is 0
no_recovery_img="${NO_RECOVERY_IMG:-0}"
boardid="${BOARDID}";
if [ "${tegraid}" = "" ]; then
	tegraid="${CHIPID}";
fi;

if [ -z "${DFLT_KERNEL}" ]; then
	DFLT_KERNEL=${KERNEL_DIR}/Image;
else
	basekernel=`basename "${DFLT_KERNEL}"`;
	if [ "${DFLT_KERNEL}" = "${basekernel}" ]; then
		DFLT_KERNEL="${KERNEL_DIR}/${DFLT_KERNEL}";
	fi;
fi;
if [ -z "${DFLT_KERNEL_FS}" ]; then
	DFLT_KERNEL_FS=${DFLT_KERNEL};
fi;
if [ -z "${DFLT_KERNEL_IMAGE}" ]; then
	DFLT_KERNEL_IMAGE=${DFLT_KERNEL};
fi;

# as ODMDATA can be overwritten by process_board_version, overwrite with user specified option here.
if [ -n "${_ODMDATA}" ]; then
	# used by setval function below
	ODMDATA=${_ODMDATA};
fi

###########################################################################
# System mandatory vars:
#
setval     odmdata	ODMDATA;	# .conf mandatory
setval     rootfs_type	ROOTFS_TYPE;
setval     devsectsize	DEVSECTSIZE;
getsize    rootfssize	ROOTFSSIZE;	# .conf mandatory
getsize    emmcsize	EMMCSIZE;	# .conf mandatory
getsize    bootpartsize	BOOTPARTSIZE;	# .conf mandatory
getsize    bootpartlim	BOOTPARTLIMIT;
getsize    recrootfssize RECROOTFSSIZE;
mkfilepath flashapp	"${FLASHAPP}"	"${BL_DIR}/tegraflash.py";
mkfilepath flasher	"${FLASHER}"	"${BL_DIR}/cboot.bin";
mkfilepath bootloader	"${BOOTLOADER}"	"${BL_DIR}/cboot.bin";
mkdirpath  rootfs_dir	"${ROOTFS_DIR}"	"${LDK_DIR}/rootfs";
mkfilepath kernel_image	"$KERNEL_IMAGE" "${DFLT_KERNEL_IMAGE}";
mkfilepath kernel_fs	"$KERNEL_IMAGE" "${DFLT_KERNEL_FS}";
mkfilepath bctfile	"${BCTFILE}"	"${TARGET_DIR}/BCT/${EMMC_BCT}";
if [ "${CHIPID}" = "0x19" ]; then
	mkfilepath bctfile1	"${BCTFILE1}"	"${TARGET_DIR}/BCT/${EMMC_BCT1}";
fi;
mkfilepath cfgfile	"${CFGFILE}"	"${TARGET_DIR}/cfg/${EMMC_CFG}";
mkfilepath dtbfile	"${DTBFILE}"	"${DTB_DIR}/${DTB_FILE}";

mkfilesoft kernelinitrd	"${INITRD}"	"${BL_DIR}/l4t_initrd.img";
mkfilesoft tegraboot	"${TEGRABOOT}"	"${TARGET_DIR}/nvtboot.bin";
mkfilesoft wb0boot	"${WB0BOOT}"	"${TARGET_DIR}/nvtbootwb0.bin";
mkfilesoft cpu_bootloader	"${BOOTLOADER}"	"";
mkfilesoft mtspreboot	"${MTSPREBOOT}"	"${BL_DIR}/mts_preboot_si";
mkfilesoft ist_ucode	"${IST_UCODE}"	"";
mkfilesoft mcepreboot	"${MTS_MCE}"	"${BL_DIR}/${MTS_MCE}";
mkfilesoft mtsproper	"${MTSPROPER}"	"${BL_DIR}/${MTSPROPER}";
mkfilesoft mts		"${MTS}"	"${BL_DIR}/mts_si";
mkfilesoft mb1file	"${MB1FILE}"	"${BL_DIR}/mb1_prod.bin";
if [ "${BPFFILE}" != "" -a \
	"${BPFBASEFILE}" != "" -a "${BPFBASEDTBFILE}" != "" -a \
	-f "${BPFBASEFILE}" -a -f "${BPFBASEDTBFILE}" ]; then
	cat "${BPFBASEFILE}" "${BPFBASEDTBFILE}" > "${BPFFILE}";
fi;
mkfilesoft bpffile	"${BPFFILE}"	"${BL_DIR}/bpmp.bin";
mkfilesoft bpfdtbfile	"${BPFDTBFILE}" "${TARGET_DIR}/${BPFDTB_FILE}";
if [ "${bpfdtbfile}" = "" -a "${BPMPDTB_FILE}" != "" ]; then		#COMPAT
	mkfilesoft bpfdtbfile	"${BL_DIR}/${BPMPDTB_FILE}"	"";	#COMPAT
fi;									#COMPAT
mkfilesoft nctfile	"${NCTFILE}"	"${TARGET_DIR}/cfg/${NCT_FILE}";
mkfilesoft tosfile	"${TOSFILE}"	"${TARGET_DIR}/tos.img";
mkfilesoft eksfile	"${EKSFILE}"	"${TARGET_DIR}/eks.img";
mkfilesoft fbfile	"${FBFILE}"	"${BL_DIR}/${FBFILE}";
mkfilesoft bcffile	"${BCFFILE}"	"";
mkfilesoft sosfile	"${SOSFILE}"	"";
mkfilesoft mb2blfile	"${MB2BLFILE}"	"";
mkfilesoft scefile	"${SCEFILE}"	"${BL_DIR}/camera-rtcpu-sce.img";
mkfilesoft camerafw	"${CAMERAFW}"	"";
mkfilesoft apefile	"${APEFILE}"	"${BL_DIR}/adsp-fw.bin";
mkfilesoft spefile	"${SPEFILE}"	"${BL_DIR}/spe.bin";
mkfilesoft drameccfile  "${DRAMECCFILE}" "";
if [ "${BADPAGEFILE}" != "" ]; then
        if [ ! -f "${BL_DIR}/badpage.bin" ]; then
                echo "creating dummy ${BL_DIR}/badpage.bin"
                dd if=/dev/zero of="${BL_DIR}/badpage.bin" bs=4096 count=1;
        fi;
        mkfilesoft badpagefile  "${BADPAGEFILE}"	"${BL_DIR}/badpage.bin";
fi;
mkfilesoft uphy_config    "${TARGET_DIR}/BCT/${UPHY_CONFIG}" "";
mkfilesoft minratchet_config    "${TARGET_DIR}/BCT/${MINRATCHET_CONFIG}" "";
mkfilesoft device_config  "${TARGET_DIR}/BCT/${DEVICE_CONFIG}" "";
mkfilesoft misc_cold_boot_config    "${TARGET_DIR}/BCT/${MISC_COLD_BOOT_CONFIG}" "";
mkfilesoft misc_config    "${TARGET_DIR}/BCT/${MISC_CONFIG}" "";
mkfilesoft pinmux_config  "${TARGET_DIR}/BCT/${PINMUX_CONFIG}" "";
mkfilesoft gpioint_config  "${TARGET_DIR}/BCT/${GPIOINT_CONFIG}" "";
mkfilesoft pmic_config    "${TARGET_DIR}/BCT/${PMIC_CONFIG}" "";
mkfilesoft pmc_config     "${TARGET_DIR}/BCT/${PMC_CONFIG}" "";
mkfilesoft prod_config    "${TARGET_DIR}/BCT/${PROD_CONFIG}" "";
mkfilesoft scr_config     "${TARGET_DIR}/BCT/${SCR_CONFIG}" "";
mkfilesoft scr_cold_boot_config     "${TARGET_DIR}/BCT/${SCR_COLD_BOOT_CONFIG}" "";
mkfilesoft dev_params     "${TARGET_DIR}/BCT/${DEV_PARAMS}" "";
mkfilesoft bootrom_config "${TARGET_DIR}/BCT/${BOOTROM_CONFIG}" "";
mkfilesoft soft_fuses     "${TARGET_DIR}/BCT/${SOFT_FUSES}" "";
mkfilesoft tbcfile	"${TBCFILE}"	 "";
mkfilesoft tbcdtbfile	"${TBCDTB_FILE}" "${DTB_DIR}/${DTB_FILE}";
mkfilesoft cbootoptionfile	"${CBOOTOPTION_FILE}"	"${TARGET_DIR}/cbo.dtb";
mkfilesoft varstorefile "${VARSTORE_FILE}" "";
if [ "${tegraid}" = "0x18" ] || [ "${tegraid}" = "0x19" ] \
	&& { [ "${target_partname}" == "" ] || [ "${target_partname}" == "recovery-dtb" ]; } \
	&& [ ${bup_blob} -eq 0 ]; then
	if [ -f "${DTB_DIR}/${DTB_FILE}" ]; then
		echo "Copy "${DTB_DIR}/${DTB_FILE} to "${DTB_DIR}/${DTB_FILE}.rec"
		cp "${DTB_DIR}/${DTB_FILE}" "${DTB_DIR}/${DTB_FILE}.rec"
	fi
	mkfilepath recdtbfile   "${RECDTB_FILE}" "${DTB_DIR}/${DTB_FILE}.rec";
fi

if [ "${rootdev_type}" = "network" ]; then
	if [ "${NFSROOT}" = "" -a "${NFSARGS}" = "" ]; then
		echo "Error: network argument(s) missing.";
		usage allknown 1;
	fi;
	if [ "${NFSROOT}" != "" ]; then
		validateNFSroot nfsroot "${NFSROOT}";
	fi;
	if [ "${NFSARGS}" != "" ]; then
		validateNFSargs nfsargs "${NFSARGS}";
	fi;
	if [ "${nfsroot}" != "" ]; then
		nfsdargs="root=/dev/nfs rw netdevwait";
		cmdline+="${nfsdargs} ";
		if [ "${nfsargs}" != "" ]; then
			nfsiargs="ip=${nfsargs}";
			nfsiargs+="::${target_rootdev}:off";
		else
			nfsiargs="ip=:::::${target_rootdev}:on";
		fi;
		cmdline+="${nfsiargs} ";
		cmdline+="nfsroot=${nfsroot} ";
	fi;
elif [ "${target_rootdev}" = "cloning_root" ]; then
	if [ "${tegraid}" = "0x21" ]; then
		# Nano
		CMDLINE_ADD="console=ttyS0,115200n8 sdhci_tegra.en_boot_part_access=1";
	elif [ "${tegraid}" = "0x18" ]; then
		# TX2
		CMDLINE_ADD="console=ttyS0,115200n8";
	elif [ "${tegraid}" = "0x19" ]; then
		# Xavier
		CMDLINE_ADD="console=ttyTCU0,115200n8";
	else
		echo "Unknown tegraid/board,exiting..";
		exit 1
	fi;
elif [ "${target_rootdev}" == "internal" ] || \
     [ "${target_rootdev}" == "external" ] || \
     [[ "${rootfs_ab}" == 1 ]]; then
	# For 'internal' and 'external' target root devices,
	# or enabled ROOTFS_AB=1, always use the UUID stored in the file
	# ${rootfsuuidfile} or ${rootfsuuidfile}_b if present.
	# If this file is not present, then try to generate one.
	_tmp_uuid="";

	if [ "${target_rootdev}" == "external" ] || \
	[ "${external_device}" -eq 1 ]; then
		rootuuid_restore "_ext"
		_tmp_uuid="${rootfsuuid_ext}";
	else
		rootuuid_restore ""
		_tmp_uuid="${rootfsuuid}";
	fi

	if [ ${disk_enc_enable} -eq 1 ]; then
		# The encrypted fs UUID of the rootdev.
		if [ "${external_device}" -eq 1 ]; then
			rootuuid_restore "_ext_enc"
			_tmp_uuid="${rootfsuuid_ext_enc}";

			bootpartuuid_restore "_ext"
			rootfsuuid_enc="${rootfsuuid_ext_enc}"
			rootfsuuid_b_enc="${rootfsuuid_b_ext_enc}"
			# These variables are set in disk_encryption_helper.func
			bootpartuuid="${bootpartuuid_ext}"
			# These variables are set in disk_encryption_helper.func
			bootpartuuid_b="${bootpartuuid_b_ext}"
		else
			rootuuid_restore "_enc";
			_tmp_uuid="${rootfsuuid_enc}";

			bootpartuuid_restore;
		fi

		cmdline+="root=UUID=${_tmp_uuid} rw rootwait rootfstype=ext4 "
	else
		cmdline+="root=PARTUUID=${_tmp_uuid} rw rootwait rootfstype=ext4 "
	fi;
else
	cmdline+="root=/dev/${target_rootdev} rw rootwait rootfstype=ext4 "
fi;

if [ "${CMDLINE_ADD}" != "" ]; then
	cmdline+="${CMDLINE_ADD} ";
fi;

if [ "${CMDLINE}" != "" ]; then
	for string in ${CMDLINE}; do
		lcl_str=`echo $string | sed "s|\(.*\)=.*|\1|"`
		if [[ "${cmdline}" =~ $lcl_str ]]; then
			cmdline=`echo "$cmdline" | sed "s|$lcl_str=[0-9a-zA-Z:/]*|$string|"`
		else
			cmdline+="${string} ";
		fi
	done
fi;

##########################################################################
if [ "${zflag}" == "true" ]; then
	pr_conf;
	exit 0;
fi;
##########################################################################

pushd "$BL_DIR" > /dev/null 2>&1;

### Localize files and build TAGS ########################################
# BCT_TAG:::
#
cp2local bctfile "${BL_DIR}/${bctfilename}";
if [ "${CHIPID}" = "0x19" ]; then
	cp2local bctfile1 "${BL_DIR}/${bctfile1name}";
fi;
if [ "${BINSARGS}" != "" ]; then
	# Build up BCT parameters:

	if [ "${uphy_config}" != "" ]; then
		cp2local uphy_config "${BL_DIR}/${uphy_configname}";
		BCTARGS+="--uphy_config ${uphy_configname} ";
	fi;
	if [ "${minratchet_config}" != "" ] && [ "${target_partname}" = "" ]; then
		cp2local minratchet_config "${BL_DIR}/${minratchet_configname}";
		BCTARGS+="--minratchet_config ${minratchet_configname} ";
	fi;
	if [ "${device_config}" != "" ]; then
		cp2local device_config "${BL_DIR}/${device_configname}";
		BCTARGS+="--device_config ${device_configname} ";
	fi;
	if [ "${misc_cold_boot_config}" != "" ]; then
		cp2local misc_cold_boot_config "${BL_DIR}/${misc_cold_boot_configname}";
		BCTARGS+="--misc_cold_boot_config ${misc_cold_boot_configname} ";
	fi;
	if [ "${misc_config}" != "" ]; then
		cp2local misc_config "${BL_DIR}/${misc_configname}";
		BCTARGS+="--misc_config ${misc_configname} ";
	fi;
	if [ "${pinmux_config}" != "" ]; then
		cp2local pinmux_config "${BL_DIR}/${pinmux_configname}";
		BCTARGS+="--pinmux_config ${pinmux_configname} ";
	fi;
	if [ "${gpioint_config}" != "" ]; then
		cp2local gpioint_config "${BL_DIR}/${gpioint_configname}";
		BCTARGS+="--gpioint_config ${gpioint_configname} ";
	fi;
	if [ "${pmic_config}" != "" ]; then
		cp2local pmic_config "${BL_DIR}/${pmic_configname}";
		BCTARGS+="--pmic_config ${pmic_configname} ";
	fi;
	if [ "${pmc_config}" != "" ]; then
		cp2local pmc_config "${BL_DIR}/${pmc_configname}";
		BCTARGS+="--pmc_config ${pmc_configname} ";
	fi;
	if [ "${prod_config}" != "" ]; then
		cp2local prod_config "${BL_DIR}/${prod_configname}";
		BCTARGS+="--prod_config ${prod_configname} ";
	fi;
	if [ "${scr_config}" != "" ]; then
		cp2local scr_config "${BL_DIR}/${scr_configname}";
		BCTARGS+="--scr_config ${scr_configname} ";
	fi;
	if [ "${scr_cold_boot_config}" != "" ]; then
		cp2local scr_cold_boot_config "${BL_DIR}/${scr_cold_boot_configname}";
		BCTARGS+="--scr_cold_boot_config ${scr_cold_boot_configname} ";
	fi;
	if [ "${bootrom_config}" != "" ]; then
		cp2local bootrom_config "${BL_DIR}/${bootrom_configname}";
		BCTARGS+="--br_cmd_config ${bootrom_configname} ";
	fi;
	if [ "${dev_params}" != "" ]; then
		cp2local dev_params "${BL_DIR}/${dev_paramsname}";
		BCTARGS+="--dev_params ${dev_paramsname} ";
	fi;
	if [ "${BCT}" = "" ]; then
		BCT="--sdram_config";
	fi;
elif [ "${BCT}" = "" ]; then
	BCT="--bct";
fi;

# check cases where system.img is not needed
if [ ${bup_blob} -eq 1 ] || [ ${rcm_boot} -eq 1 ] \
	|| [ "${no_rootfs}" -eq 1 ] \
	|| [ "${no_systemimg}" -eq 1 ] \
	|| [ "${read_part_name}" != "" ]; then
	skip_systemimg="true";
fi;

# UDA_TAG:
#
# Create the UDA encrypted disk image if the attribuate "encrypted" is true.
if [ ${disk_enc_enable} -eq 1 ]; then
	if [ "${external_device}" -eq 1 ]; then
		udaext="_ext"
	fi
	if [ "${reuse_systemimg}" = "true" ] || [ "${skip_systemimg}" = "true" ]; then
		echo "Skip generating encrypted UDA partition";
	else
		create_enc_user_disk "UDA" "${cfgfile}" "${fillpat}" "${rootfs_type}" "${ECID}" "" "${udaext}";
	fi
fi;

# EBT_TAG:
#
cp2local bootloader "${BL_DIR}/${bootloadername}";
EBT_TAG+="-e s/EBTFILE/${bootloadername}/ ";

# LNX_TAG:
#
localbootfile=boot.img;
rm -f initrd; touch initrd;
if [[ "${rootfs_ab}" == 1 && "${disk_enc_enable}" == 1 ]]; then
	rm -f initrd_b; touch initrd_b;
fi;
if [ ${rcm_boot} -eq 1 ]; then
	if [ "${kernelinitrd}" = "" ]; then
		kernelinitrd=l4t_initrd.img
	fi;
fi;
if [ "$kernelinitrd" != "" -a -f "$kernelinitrd" ]; then
	echo -n "copying initrd(${kernelinitrd})... ";
	cp -f "${kernelinitrd}" initrd;
	if [[ "${rootfs_ab}" == 1 && "${disk_enc_enable}" == 1 ]]; then
		cp -f "${kernelinitrd}" initrd_b;
	fi;
	chkerr;
	# Code below for the initrd boot. Further details: see 2053323
	if [ "${target_rootdev}" = "cloning_root" ]; then
		clone_restore_dir="${LDK_DIR}/clone_restore"
		if [ ! -f ${clone_restore_dir}/nvbackup_copy_bin.func ]; then
			echo "Error: cloning is not supported."
			exit 1
		fi
		echo "Extract kernel initrd"
		initrddir="${BL_DIR}"
		tempinitrd_dir="${initrddir}/temp"
		if [ ! -d "${tempinitrd_dir}" ]; then
			mkdir "${tempinitrd_dir}"
		fi
		temp_initrd="initrd"
		pushd "${tempinitrd_dir}"  > /dev/null 2>&1;
		source "${clone_restore_dir}/nvbackup_copy_bin.func"
		nvbackup_copy_bin "${clone_restore_dir}" \
			"${rootfs_dir}" \
			"${initrddir}/${temp_initrd}" \
			"${clone_restore_dir}/nvbackup_env_binlist.txt" \
			"${spec}"
		if [ $? -ne 0 ]; then
			rm -rf "${tempinitrd_dir}"
			echo "nvbackup_copy_bin: Failed"
			exit 1
		fi
		popd  > /dev/null 2>&1;
		rm -rf "${tempinitrd_dir}"
	fi;

	# Update initrd for LUKS disk encryption support
	if [ ${disk_enc_enable} -eq 1 ]; then
		# Prepare the needed binaries
		prepare_luks_bin_list "${LDK_DIR}" "${rootfs_dir}" luks_bin_list
		luks_bin_list+=("/sbin/cryptsetup" "/usr/sbin/nvluks-srv-app");

		# Prepare the initrd
		initrddir="${BL_DIR}";
		tempinitrd="${initrddir}/initrd";
		tempinitrddir="${initrddir}/temp";
		if [ ! -d "${tempinitrddir}" ]; then
			mkdir -p "${tempinitrddir}";
		fi;
		pushd "${tempinitrddir}" > /dev/null 2>&1;
		prepare_luks_initrd "${tempinitrd}" "${rootfs_dir}" "${rootfsuuid_enc}" "${luks_bin_list[@]}"
		popd > /dev/null 2>&1;
		chkerr;

		if [[ "${rootfs_ab}" == 1 ]]; then
			rm -rf ${tempinitrddir}/*;
			tempinitrd="${initrddir}/initrd_b";
			pushd "${tempinitrddir}" > /dev/null 2>&1;
			prepare_luks_initrd "${tempinitrd}" "${rootfs_dir}" "${rootfsuuid_b_enc}" "${luks_bin_list[@]}"
			popd > /dev/null 2>&1;
			chkerr;
		fi;

		# Clean up
		rm -rf "${tempinitrddir}";
	fi;
fi;

LNX_TAG+="-e s/LNXNAME/kernel/ ";
LNX_TAG+="-e s/LNXSIZE/83886080/ ";
# Handle where kernel image is specified by -k and --image options
if [ "${write_image_name}" != "" ]; then
	if [ "${target_partname}" = "LNX" ] || [ "${target_partname}" = "kernel" ] \
		|| [ "${target_partname}" = "kernel_b" ]; then
		kernel_image="${write_image_name}";
		write_image_name="";
	fi
fi

if [ "${INITRD_IN_BOOTIMG}" = "yes" ]; then
	ramdisk=initrd;
	if [[ "${rootfs_ab}" == 1 && "${disk_enc_enable}" == 1 ]]; then
		ramdisk_b=initrd_b;
	fi
else
	ramdisk="/dev/null"
	if [[ "${rootfs_ab}" == 1 && "${disk_enc_enable}" == 1 ]]; then
		ramdisk_b="/dev/null";
	fi
fi

if [[ "${rootfs_ab}" == 1 ]]; then
	if [ "${target_rootdev}" == "external" ] || \
	[ "${external_device}" -eq 1 ]; then
		cmdline_b="${cmdline//${rootfsuuid_ext}/${rootfsuuid_b_ext}}"
	else
		if [ ${disk_enc_enable} -eq 1 ]; then
			if [ "${external_device}" -eq 1 ]; then
				cmdline_b="${cmdline//${rootfsuuid_ext_enc}/${rootfsuuid_b_ext_enc}}"
			else
				cmdline_b="${cmdline//${rootfsuuid_enc}/${rootfsuuid_b_enc}}"
			fi
		else
			cmdline_b="${cmdline//${rootfsuuid}/${rootfsuuid_b}}"
		fi
	fi
fi

make_boot_image

# boot.img is ready:
# For T19x and T18x, generate encrypted/signed file of boot.img in a temp folder.
if [ "${tegraid}" = "0x19" ] || [ "${tegraid}" = "0x18" ]; then
	temp_user_dir="temp_user_dir";
	rm -rf "${temp_user_dir}" > /dev/null 2>&1;
	mkdir -p "${temp_user_dir}"; chkerr "failed to mkdir ${temp_user_dir}";
	cp ${localbootfile} ${temp_user_dir} > /dev/null 2>&1;
	if [ -f "${localbootfile}_b" ]; then
		cp "${localbootfile}_b" "${temp_user_dir}" > /dev/null 2>&1;
	fi
	pushd ${temp_user_dir} > /dev/null 2>&1 || exit 1;
	# Set --split to False (to generate encrypt_signed file)
	signimage ${localbootfile} "False" "kernel" "${minratchet_configname}";
	if [ -f "${localbootfile}_b" ]; then
		signimage "${localbootfile}_b" "False" "kernel" "${minratchet_configname}"
	fi
	popd > /dev/null 2>&1 || exit 1;
fi

LNX_TAG+="-e s/LNXFILE/${localbootfile}/ ";

# Build recovery image and dtb
# recovery.img set to 63M, and leave 512KB for
# recovery-dtb and 512KB for kernel-bootctrl
REC_SIZE_DEF=66060288
RECROOTFS_SIZE_DEF=314572800
REC_TAG+="-e s/RECNAME/recovery/ ";
REC_TAG+="-e s/RECSIZE/${REC_SIZE_DEF}/ "
RECDTB_TAG+="-e s/RECDTB-NAME/recovery-dtb/ ";
BOOTCTRL_TAG+="-e s/BOOTCTRLNAME/kernel-bootctrl/ ";
if [ "${tegraid}" = "0x18" ] || [ "${tegraid}" = "0x19" ] && [ "${no_recovery_img}" -eq 0 ] \
	&& { [ "${target_partname}" == "" ] || [ "${target_partname}" == "recovery" ] || [ "${target_partname}" == "recovery-dtb" ]; } \
	&& [ ${bup_blob} -eq 0 ]; then
	make_recovery_script="${LDK_DIR}/tools/ota_tools/version_upgrade/ota_make_recovery_img_dtb.sh"
	if [ -f "${make_recovery_script}" ];then
		source "${make_recovery_script}"

		if [ "${target_partname}" == "" ] || [ "${target_partname}" == "recovery" ]; then
			localrecfile="recovery.img"
			ota_make_recovery_img "${LDK_DIR}" "${kernel_fs}" "${kernelinitrd}" "${localrecfile}" "${tegraid}"
			REC_TAG+="-e s/RECFILE/${localrecfile}/ ";
		else
			REC_TAG+="-e /RECFILE/d ";
		fi

		if [ "${target_partname}" == "" ] || [ "${target_partname}" == "recovery-dtb" ]; then
			if [ "${recdtbfile}" != "" ] && [ -f "${recdtbfile}" ];then
				ota_make_recovery_dtb "${LDK_DIR}" "${recdtbfilename}"
				RECDTB_TAG+="-e s/RECDTB-FILE/${recdtbfilename}/ ";
			else
				echo "Recovery dtb file is missing"
				exit 1
			fi
		else
			RECDTB_TAG+="-e /RECDTB-FILE/d ";
		fi
	else
		REC_TAG+="-e /RECFILE/d ";
		RECDTB_TAG+="-e /RECDTB-FILE/d ";
	fi

	if [ "${MSI_EMMC_OFFSET}" != "" ]; then
		REC_TAG+="-e s/MSI_EMMC_OFFSET/${MSI_EMMC_OFFSET}/ "
	fi

	# BOOTCTRL_TAG: Kernel boot control metadata
	#
	BOOTCTRL_TAG+="-e s/BOOTCTRL-FILE/kernel_bootctrl.bin/ ";
	BOOTCTRL_FILE_SIZE=20
	# make a dummpy kernel_bootctrl.bin for generating index file for OTA
	dd if=/dev/zero of=kernel_bootctrl.bin bs=1 count=${BOOTCTRL_FILE_SIZE}
else
	REC_TAG+="-e /RECFILE/d ";
	RECDTB_TAG+="-e /RECDTB-FILE/d ";
	BOOTCTRL_TAG+="-e /BOOTCTRL-FILE/d ";
fi
# RECROOTFS partition size is set to 300MiB if RECROOTFSSIZE is not set
if [ -z "${recrootfssize}" ];then
	RECROOTFS_TAG="-e s/RECROOTFSSIZE/${RECROOTFS_SIZE_DEF}/ ";
else
	RECROOTFS_TAG="-e s/RECROOTFSSIZE/${recrootfssize}/ ";
fi

# NCT_TAG:
#
if [ "${bcffile}" != "" ]; then
	cp2local bcffile "${BL_DIR}/${bcffilename}";
	NCTARGS+="--boardconfig ${bcffilename} ";
	NCT_TAG+="-e /NCTFILE/d ";
	NCT_TAG+="-e s/NCTTYPE/data/ ";
elif [ "${boardid}" != "" ]; then
	: # Do nothing
elif [ "${nctfile}" != "" ]; then
	cp2local nctfile "${BL_DIR}/${nctfilename}";
	NCT_TAG+="-e s/NCTFILE/${nctfilename}/ ";
	NCT_TAG+="-e s/NCTTYPE/config_table/ ";
	NCTARGS+="--nct ${nctfilename} ";
else
	NCT_TAG+="-e /NCTFILE/d ";
	NCT_TAG+="-e s/NCTTYPE/data/ ";
fi;

# VER_TAG:
#
if [ "${VERFILENAME}" != "" ]; then
	# NV1: VersionID,ReleaseString
	# NV2: VersionID,ReleaseString,BoardID
	# NV3: VersionID,ReleaseString,BoardID,Timestamp,CRC32
	echo "NV3" > "${VERFILENAME}";	# Version file format number
	if [ -f "${LDK_DIR}/nv_tegra/bsp_version" ]; then
		echo "# R${BSP_BRANCH} , REVISION: ${BSP_MAJOR}.${BSP_MINOR}" >> "${VERFILENAME}";
	else
		head -n 1 "${rootfs_dir}/etc/nv_tegra_release" >> "${VERFILENAME}";
	fi;
	echo "BOARDID=${BOARDID} BOARDSKU=${BOARDSKU} FAB=${FAB}" >> "${VERFILENAME}";
	VER_TIMESTAMP="$(date -R)"
	TIMESTAMP=$(date -d "$VER_TIMESTAMP" +%Y%m%d%H%M%S)
	echo "${TIMESTAMP}" >> "${VERFILENAME}";
	CKSUM=$( cksum "${VERFILENAME}" );
	CRC32=$( echo "${CKSUM}" | awk '{print $1}' )
	NUM_BYTES=$( echo "${CKSUM}" | awk '{print $2}' )
	echo "BYTES:${NUM_BYTES} CRC32:${CRC32}" >> "${VERFILENAME}";
	VER_TAG+="-e s/VERFILE/${VERFILENAME}/ ";
else
	VER_TAG+="-e /VERFILE/d ";
fi;

# SOS_TAG: XXX: recovery is yet to be implemented.
#
SOS_TAG+="-e /SOSFILE/d ";
if [ "${sosfile}" != "" ]; then
	cp2local sosfile "${BL_DIR}/${sosfilename}";
	SOSARGS+="--applet ${sosfilename} ";
fi;

# NVC_TAG:== MB2
#
if [ "${tegraboot}" != "" ]; then
	cp2local tegraboot "${BL_DIR}/${tegrabootname}";
	cp2local cpu_bootloader "${BL_DIR}/${cpu_bootloadername}";
	NVC_TAG+="-e s/NXC/NVC/ ";
	NVC_TAG+="-e s/MB2NAME/mb2/ ";
	NVC_TAG+="-e s/NVCTYPE/bootloader/ ";
	NVC_TAG+="-e s/TEGRABOOT/${tegrabootname}/ ";
	NVC_TAG+="-e s/MB2TYPE/mb2_bootloader/ ";
	NVC_TAG+="-e s/NVCFILE/${tegrabootname}/ ";
	NVC_TAG+="-e s/MB2FILE/${tegrabootname}/ ";
else
	NVC_TAG+="-e s/NVCTYPE/data/ ";
	NVC_TAG+="-e s/MB2TYPE/data/ ";
	NVC_TAG+="-e /NVCFILE/d ";
	NVC_TAG+="-e /MB2FILE/d ";
fi;

# MB2BL_TAG:== tboot_recovery
#
if [ "${mb2blfile}" != "" ]; then
	cp2local mb2blfile "${BL_DIR}/${mb2blfilename}";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="mb2_bootloader ${mb2blfilename}; ";
	fi;
fi;

# IST_TAG:
#
if [ "${ist_ucode}" != "" ]; then
	cp2local ist_ucode "${BL_DIR}/${ist_ucodename}";
	IST_TAG+="-e s/ISTUCODE/${ist_ucodename}/ ";
fi;

# MPB_TAG:
#
if [ "${mtspreboot}" != "" ]; then
	cp2local mtspreboot "${BL_DIR}/${mtsprebootname}";
	MPB_TAG+="-e s/MXB/MPB/ ";
	MPB_TAG+="-e s/MPBNAME/mts-preboot/ ";
	MPB_TAG+="-e s/MPBTYPE/mts_preboot/ ";
	MPB_TAG+="-e s/MPBFILE/${mtsprebootname}/ ";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="mts_preboot ${mtsprebootname}; ";
		if [ "${CHIPID}" = "0x19" ]; then
			cp2local mcepreboot "${BL_DIR}/${mceprebootname}";
			cp2local mtsproper "${BL_DIR}/${mtspropername}";
			MPB_TAG+="-e s/MTSPREBOOT/${mtsprebootname}/ ";
			MPB_TAG+="-e s/MTS_MCE/${mceprebootname}/ ";
			MPB_TAG+="-e s/MTSPROPER/${mtspropername}/ ";
			BINSARGS+="mts_mce ${mceprebootname}; ";
			BINSARGS+="mts_proper ${mtspropername}; ";
		fi;
	else
		MTSARGS+="--preboot ${mtsprebootname} ";
	fi;
else
	MPB_TAG+="-e s/MPBTYPE/data/ ";
	MPB_TAG+="-e /MPBFILE/d ";
fi;

# MBP_TAG:
#
if [ "${mts}" != "" ]; then
	cp2local mts "${BL_DIR}/${mtsname}";
	MBP_TAG+="-e s/MXP/MBP/ ";
	MBP_TAG+="-e s/MBPNAME/mts-bootpack/ ";
	MBP_TAG+="-e s/MBPTYPE/mts_bootpack/ ";
	MBP_TAG+="-e s/MBPFILE/${mtsname}/ ";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="mts_bootpack ${mtsname}; ";
	else
		MTSARGS+="--bootpack ${mtsname} ";
	fi;
else
	MBP_TAG+="-e s/MBPTYPE/data/ ";
	MBP_TAG+="-e /MBPFILE/d ";
fi;

# MB1_TAG:
#
if [ "${mb1file}" != "" ]; then
	cp2local mb1file "${BL_DIR}/${mb1filename}";
	MB1_TAG+="-e s/MB1NAME/mb1/ ";
	MB1_TAG+="-e s/MB1TYPE/mb1_bootloader/ ";
	MB1_TAG+="-e s/MB1FILE/${mb1filename}/ ";
else
	MB1_TAG+="-e s/MB1TYPE/data/ ";
	MB1_TAG+="-e /MB1FILE/d ";
fi;

# BPF_TAG:
#
if [ "${bpffile}" != "" ]; then
	cp2local bpffile "${BL_DIR}/${bpffilename}";
	BPF_TAG+="-e s/BXF/BPF/ ";
	BPF_TAG+="-e s/BPFNAME/bpmp-fw/ ";
	BPF_TAG+="-e s/BPFFILE/${bpffilename}/ ";
	BPF_TAG+="-e s/BPFSIGN/true/ ";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="bpmp_fw ${bpffilename}; ";
	fi;
else
	BPF_TAG+="-e /BPFFILE/d ";
	BPF_TAG+="-e s/BPFSIGN/false/ ";
fi;

# BPFDTB_TAG:
if [ "${bpfdtbfile}" != "" ]; then
	cp2local bpfdtbfile "${BL_DIR}/${bpfdtbfilename}";
	BPFDTB_TAG+="-e s/BPFDTB-NAME/bpmp-fw-dtb/ ";
	BPFDTB_TAG+="-e s/BPFDTB-FILE/${bpfdtbfilename}/ ";
	BPFDTB_TAG+="-e s/BPFDTB_FILE/${bpfdtbfilename}/ ";
	BPFDTB_TAG+="-e s/BPMPDTB-SIGN/true/ ";
	BPFDTB_TAG+="-e s/BPMPDTB/${bpfdtbfilename}/ ";			#COMPAT
	BPFDTB_TAG+="-e s/BXF-DTB/BPF-DTB/ ";				#COMPAT
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="bpmp_fw_dtb ${bpfdtbfilename}; ";
	fi;
else
	BPFDTB_TAG+="-e /BPFDTB-FILE/d ";				#COMPAT
	BPFDTB_TAG+="-e s/BPMPDTB-SIGN/false/ ";
fi;

# SCE_TAG:
if [ "${scefile}" != "" -o "${camerafw}" != "" ]; then
	cp2local scefile "${BL_DIR}/${scefilename}";
	cp2local camerafw "${BL_DIR}/${camerafwname}";
	SCE_TAG+="-e s/SCENAME/sce-fw/ ";
	SCE_TAG+="-e s/SCESIGN/true/ ";
	SCE_TAG+="-e s/SCEFILE/${scefilename}/ ";
	SCE_TAG+="-e s/CAMERAFW/${camerafwname}/ ";
else
	SCE_TAG+="-e s/SCESIGN/flase/ ";
	SCE_TAG+="-e /SCEFILE/d ";
fi;

# SPE_TAG:
if [ "${spefile}" != "" ]; then
	cp2local spefile "${BL_DIR}/${spefilename}";
	SPE_TAG+="-e s/SPENAME/spe-fw/ ";
	SPE_TAG+="-e s/SPETYPE/spe_fw/ ";
	SPE_TAG+="-e s/SPEFILE/${spefilename}/ ";
	if [ "${BINSARGS}" != "" -a "${CHIPID}" = "0x19" ]; then
	     BINSARGS+="spe_fw ${spefilename}; ";
	fi;

else
	SPE_TAG+="-e s/SPETYPE/data/ ";
	SPE_TAG+="-e /SPEFILE/d ";
fi;

# DRAMECC_TAG:
if [ "${drameccfile}" != "" ]; then
	cp2local drameccfile "${BL_DIR}/${drameccfilename}";
	DRAMECC_TAG+="-e s/DRAMECCNAME/dram-ecc-fw/ ";
	DRAMECC_TAG+="-e s/DRAMECCTYPE/dram_ecc/ ";
	DRAMECC_TAG+="-e s/DRAMECCFILE/${drameccfilename}/ ";
else
	DRAMECC_TAG+="-e s/DRAMECCTYPE/data/ ";
	DRAMECC_TAG+="-e /DRAMECCFILE/d ";
fi;

# BADPAGE_TAG:
if [ "${badpagefile}" != "" ]; then
	cp2local badpagefile "${BL_DIR}/${badpagefilename}";
	BADPAGE_TAG+="-e s/BADPAGENAME/badpage-fw/ ";
	BADPAGE_TAG+="-e s/BADPAGETYPE/black_list_info/ ";
	BADPAGE_TAG+="-e s/BADPAGEFILE/${badpagefilename}/ ";
else
	BADPAGE_TAG+="-e s/BADPAGETYPE/data/ ";
	BADPAGE_TAG+="-e /BADPAGEFILE/d ";
fi;


# WB0_TAG:
#
if [ "${wb0boot}" != "" ]; then
	cp2local wb0boot "${BL_DIR}/${wb0bootname}";
	WB0_TAG+="-e s/WX0/WB0/ ";
	WB0_TAG+="-e s/SC7NAME/sc7/ ";
	WB0_TAG+="-e s/WB0TYPE/WB0/ ";
	WB0_TAG+="-e s/WB0FILE/${wb0bootname}/ ";
	WB0_TAG+="-e s/WB0BOOT/${wb0bootname}/ ";
else
	WB0_TAG+="-e s/WB0TYPE/data/ ";
	WB0_TAG+="-e /WB0FILE/d ";
fi;

# TOS_TAG:
#
if [ "${tosfile}" != "" ]; then
	cp2local tosfile "${BL_DIR}/${tosfilename}";
	TOS_TAG+="-e s/TXS/TOS/ ";
	TOS_TAG+="-e s/TOSNAME/secure-os/ ";
	TOS_TAG+="-e s/TOSFILE/${tosfilename}/ ";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="tlk ${tosfilename}; ";
	fi;
else
	TOS_TAG+="-e /TOSFILE/d ";
fi;

# EKS_TAG:
#
EKS_TAG+="-e s/EXS/EKS/ ";
if [ "${eksfile}" != "" ]; then
	cp2local eksfile "${BL_DIR}/${eksfilename}";
	EKS_TAG+="-e s/EKSFILE/${eksfilename}/ ";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="eks ${eksfilename}; ";
	fi;
else
	EKS_TAG+="-e /EKSFILE/d ";
fi;

# FB_TAG:
#
if [ "${fbfile}" != "" ]; then
	chsuffix fbfilebin ${fbfilename} "bin";
	cp2local fbfile "${BL_DIR}/${fbfilename}";
	FB_TAG+="-e s/FBFILE/${fbfilebin}/ ";
	FB_TAG+="-e s/FX/FB/ ";
	FB_TAG+="-e s/FBNAME/fusebypass/ ";
	FB_TAG+="-e s/FBTYPE/fuse_bypass/ ";
	FB_TAG+="-e s/FBSIGN/true/ ";
	if [[ "${CHIPID}" != "0x19"  ||  "${fuselevel}" = "fuselevel_nofuse" ]]; then
		FBARGS+="--fb ${fbfilebin} "
		FBARGS+="--cmd \"parse fusebypass ${fbfilename} ";
	else
		# T194 nv fused board: skip --fb xxx and "parse fusebypass xxx.xml acr-debug"
		FBARGS+="--cmd \"";
	fi
	if [ "${CHIPID}" = "0x19" ]; then
		if [ "${fuselevel}" = "fuselevel_nofuse" ]; then
			FBARGS+="${ACR_TYPE}; ";
		fi
		if [ ${bup_blob} -ne 0 ] || [ ${to_sign} -ne 0 ]; then
			FBARGS+="sign\" ";
		elif [ ${rcm_boot} -ne 0 ]; then
			FBARGS+="rcmboot\" ";
		else
			FBARGS+="flash;reboot\" ";
		fi
		BINSARGS+="kernel boot.img; "
		BINSARGS+="kernel_dtb ${DTB_FILE}; "
	else
		if [ "${CHIPMAJOR}" != "" ]; then
			FBARGS+="b01-acr-production; ";
		else
			FBARGS+="non-secure; ";
		fi;
		FBARGS+="flash; reboot\" ";
	fi;
else
	FB_TAG+="-e s/FBTYPE/data/ ";
	FB_TAG+="-e s/FBSIGN/false/ ";
	FB_TAG+="-e /FBFILE/d ";
	if [ ${rcm_boot} -ne 0 ]; then
		if [ "${CHIPID}" = "0x21" ]; then
			BINSARGS=""
		else
			BINSARGS+="kernel boot.img; "
			BINSARGS+="kernel_dtb ${DTB_FILE}; "
			if [ "${CHIPID}" = "0x18" ]; then
				BINSARGS+="sce_fw ${scefilename}; "
				BINSARGS+="adsp_fw ${apefilename}; "
			fi
		fi
		FBARGS+="--cmd \"rcmboot\" ";
	elif [ ${bup_blob} -ne 0 ] || [ ${to_sign} -ne 0 ]; then
		FBARGS+="--cmd \"sign\" ";
	else
		FBARGS+="${IGNOREBFS} --cmd \"flash; reboot\" ";
	fi
fi;

# soft_fuse:
#
if [ "${soft_fuses}" != "" ]; then
	cp2local soft_fuses "${BL_DIR}/${soft_fusesname}";
	NV_ARGS+="--soft_fuses ${soft_fusesname} ";
fi;

# DTB_TAG: Kernel DTB
#
if [ "${dtbfile}" != "" ]; then
	cp2local dtbfile "${BL_DIR}/${dtbfilename}";
	cp "${BL_DIR}/${dtbfilename}" "${BL_DIR}/kernel_${dtbfilename}"
	dtbfilename="kernel_${dtbfilename}";

	DTB_TAG+="-e s/DXB/DTB/ ";
	DTB_TAG+="-e s/KERNELDTB-NAME/kernel-dtb/ ";
	DTB_TAG+="-e s/DTBFILE/${dtbfilename}/ ";
	DTB_TAG+="-e s/KERNELDTB-FILE/${dtbfilename}/ ";
	DTB_TAG+="-e s/DTB_FILE/${dtbfilename}/ ";			#COMPAT
	if [ "${tegraid}" != "0x18" ] && [ "${tegraid}" != "0x19"  ]; then
		if [ "${keyfile}" != "" -a "${tegraid}" = "0x21" ]; then
			DTBARGS+="--bldtb ${dtbfilename}.signed ";
		else
			DTBARGS+="--bldtb ${dtbfilename} ";
		fi;
	fi
else
	DTB_TAG+="-e /DTBFILE/d ";
	DTB_TAG+="-e /KERNELDTB-FILE/d ";
fi;

# inject board spec info into nv_boot_control.conf
echo "Copying nv_boot_control.conf to rootfs"
cp -f "${BL_DIR}/nv_boot_control.conf" "${rootfs_dir}/etc"
ota_boot_dev="/dev/mmcblk0boot0"
ota_gpt_dev="/dev/mmcblk0boot1"
if [ "${OTA_BOOT_DEVICE}" != "" ]; then
	ota_boot_dev="${OTA_BOOT_DEVICE}"
fi;
if [ "${OTA_GPT_DEVICE}" != "" ]; then
	ota_gpt_dev="${OTA_GPT_DEVICE}"
fi
sed -i '/TNSPEC/d' "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i "$ a TNSPEC ${spec}" "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i '/TEGRA_CHIPID/d' "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i "$ a TEGRA_CHIPID ${CHIPID}" "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i '/TEGRA_OTA_BOOT_DEVICE/d' "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i "$ a TEGRA_OTA_BOOT_DEVICE ${ota_boot_dev}" "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i '/TEGRA_OTA_GPT_DEVICE/d' "${rootfs_dir}/etc/nv_boot_control.conf";
sed -i "$ a TEGRA_OTA_GPT_DEVICE ${ota_gpt_dev}" "${rootfs_dir}/etc/nv_boot_control.conf";

# APP_TAG: RootFS
#

if [ ${disk_enc_enable} -eq 0 ]; then
	localsysfile=system.img;
	APP_TAG+="-e s/APPSIZE/${rootfssize}/ ";

	if [[ "${external_device}" == 1 ]]; then
		# If APPUUID and APPUUID_b exist, replace them with uuid accordingly.
		# Make sure the "APPUUID_b" is replaced before replacing "APPUUID".
		APP_TAG+="-e s/APPUUID_b/${rootfsuuid_b_ext}/ ";
		APP_TAG+="-e s/APPUUID/${rootfsuuid_ext}/ ";
	elif [[ "${target_rootdev}" == "internal" || "${rootfs_ab}" == 1 ]]; then
		# If APPUUID and APPUUID_b exist, replace them with uuid accordingly.
		# Make sure the "APPUUID_b" is replaced before replacing "APPUUID".
		APP_TAG+="-e s/APPUUID_b/${rootfsuuid_b}/ ";
		APP_TAG+="-e s/APPUUID/${rootfsuuid}/ ";
	else
		APP_TAG+="-e s/APPUUID// ";
	fi
else
	localsysbootfile="";
	localsysencrootfile="";
	bootfssize="";
	encrootfssize="";

	get_value_from_PT_table "APP" "filename" "${cfgfile}" localsysbootfile
	get_value_from_PT_table "APP_ENC" "filename" "${cfgfile}" localsysencrootfile
	get_value_from_PT_table "APP" "size" "${cfgfile}" bootfssize
	encrootfssize=$((${rootfssize}-${bootfssize}));

	if [[ "${rootfs_ab}" == 1 ]]; then
		localsysbootfile_b="";
		localsysencrootfile_b="";

		get_value_from_PT_table "APP_b" "filename" "${cfgfile}" localsysbootfile_b
		get_value_from_PT_table "APP_ENC_b" "filename" "${cfgfile}" localsysencrootfile_b

		APP_TAG+="-e s/APP_ENC_SIZE_b/${encrootfssize}/ ";
		APP_TAG+="-e s/APPUUID_b/${bootpartuuid_b}/ ";
		APP_TAG+="-e s/APP_ENC_UUID_b/${rootfsuuid_b}/ ";
	fi;

	APP_TAG+="-e s/APP_ENC_SIZE/${encrootfssize}/ ";
	APP_TAG+="-e s/APPUUID/${bootpartuuid}/ ";
	APP_TAG+="-e s/APP_ENC_UUID/${rootfsuuid}/ ";
fi;

# bl_userkey_encrypt_list contains a list of bootloader binary files
# and its bin_type (<file>:<type>) that are required to be encrypted
# with ${user_keyfile}.
# Because those files are loaded by CBoot.
bl_userkey_encrypt_list=()
if [ "${user_keyfile}" != "" ]; then
	xusb_fw_file="";
	get_value_from_PT_table "xusb-fw" "filename" "${cfgfile}" xusb_fw_file
	xusb_fw_type="";
	get_attr_from_PT_table "xusb-fw" "type" "${cfgfile}" xusb_fw_type;
	file_and_type="${xusb_fw_file}:${xusb_fw_type}";
	bl_userkey_encrypt_list+=("${file_and_type}")
fi;

# At this stage, the kernel dtb in $BL_DIR folder has the
# "bootargs=" added. We can sign dtb file now.
if [ "${tegraid}" = "0x19" ] || [ "${tegraid}" = "0x18" ]; then
	# Generate .sig file in a temp folder
	cp "${dtbfilename}" ${temp_user_dir} > /dev/null 2>&1;
	pushd ${temp_user_dir} > /dev/null 2>&1 || exit 1;
	# Generate dtb's encrypt_signed file
	# Set --split to False (to generate encrypt_signed file)
	signimage "${dtbfilename}" "False" "kernel_dtb" "${minratchet_configname}";
	popd > /dev/null 2>&1 || exit 1;
fi

if [ "${reuse_systemimg}" = "true" ] || [ "${skip_systemimg}" = "true" ]; then
	if [ ${disk_enc_enable} -eq 0 ]; then
		APP_TAG+="-e s/APPFILE/${localsysfile}/ ";
	fi;
	if [ "${skip_systemimg}" != "true" ]; then
		sysfile_exist
	else
		if [ ${disk_enc_enable} -eq 0 ]; then
			echo "Skip generating ${localsysfile}";
		else
			echo "Skip generating ${localsysbootfile} & ${localsysencrootfile}";
		fi;
	fi;
elif [ "${rootdev_type}" = "internal" ]; then
	mkdir -p "${rootfs_dir}/boot" > /dev/null 2>&1;
	echo -e -n "\tpopulating kernel to rootfs... ";
	cp -f "${kernel_fs}" "${rootfs_dir}/boot"; chkerr;
	echo -e -n "\tpopulating initrd to rootfs... ";
	cp -f initrd "${rootfs_dir}/boot"; chkerr;
	echo -e -n "\tpopulating ${dtbfilename} to rootfs... ";
	cp -f "${dtbfilename}" "${rootfs_dir}/boot"; chkerr;
	do_sign="False";
	# Sign kernel, dtb, initrd and extlinux.conf images for T19x
	if [ "${tegraid}" = "0x19" ]; then
		do_sign="True";
	fi
	create_fsimg "${rootfs_dir}" ${do_sign};
elif [ "${rootdev_type}" = "network" -o "${rootdev_type}" = "external" ]; then
	APP_TAG+="-e s/APPFILE/${localsysfile}/ ";
	echo "generating ${localsysfile} for booting... ";
	tmpdir=`mktemp -d`;
	mkdir -p "${tmpdir}/boot/extlinux" > /dev/null 2>&1;
	cp -f "${rootfs_dir}/boot/extlinux/extlinux.conf" "${tmpdir}/boot/extlinux" > /dev/null 2>&1;
	cp -f "${kernel_fs}" "${tmpdir}/boot" > /dev/null 2>&1;
	cp -f "${dtbfilename}" "${tmpdir}/boot" > /dev/null 2>&1;
	cp -f initrd "${tmpdir}/boot" > /dev/null 2>&1;
	do_sign="False";
	# Sign kernel, dtb, initrd and extlinux.conf images for T19x
	if [ "${tegraid}" = "0x19" ]; then
		do_sign="True";
	fi
	create_fsimg "${tmpdir}" ${do_sign};
else
	APP_TAG+="-e /system.img/d ";
	APP_TAG+="-e /APPFILE/d ";
fi;

# TBC_TAG:== EBT
#
if [ "${tbcfile}" != "" ]; then
	cp2local tbcfile "${BL_DIR}/${tbcfilename}";
	TBC_TAG+="-e s/TXC/TBC/ ";
	TBC_TAG+="-e s/TBCNAME/cpu-bootloader/ ";
	TBC_TAG+="-e s/TBCTYPE/bootloader/ ";
	TBC_TAG+="-e s/TBCFILE/${tbcfilename}/ ";
else
	TBC_TAG+="-e s/TBCTYPE/data/ ";
	TBC_TAG+="-e /TBCFILE/d ";
fi;

# VARSTORE_TAG:== Variable Store
#
if [ "${varstorefile}" != "" ]; then
	cp2local varstorefile "${BL_DIR}/${varstorefilename}";
	VARSTORE_TAG+="-e s/VARSTORE_FILE/${varstorefilename}/ ";
else
	VARSTORE_TAG+="-e /VARSTORE_FILE/d ";
fi;

# TBCDTB_TAG:== Bootloader DTB
#
if [ "${tbcdtbfile}" != "" ]; then
	cp2local tbcdtbfile "${BL_DIR}/${tbcdtbfilename}";
	TBCDTB_TAG+="-e s/TBCDTB-NAME/bootloader-dtb/ ";
	TBCDTB_TAG+="-e s/TBCDTB-FILE/${tbcdtbfilename}/ ";
	if [ "${BINSARGS}" != "" ]; then
		BINSARGS+="bootloader_dtb ${tbcdtbfilename}; ";
	fi;
	if [ "${T21BINARGS}" != "" ]; then
		T21BINARGS+="DTB ${tbcdtbfilename}; ";
	fi
else
	TBCDTB_TAG+="-e s/TBCTYPE/data/ ";
	TBCDTB_TAG+="-e /TBCDTB-FILE/d ";
fi;

# SMD_TAG:
#
if [ "${SMDFILE}" != "" ]; then
	SMD_TAG+="-e s/SMDFILE/${SMDFILE}/ ";
else
	# If SMD partition exists in the PT table, print
	# error message and exit as SMDFILE is not set
	if partition_exists_in_PT_table "SMD" "${cfgfile}"; then
		echo "Error: SMDFILE is not set for SMD/SMD_b partition"
		exit 1
	else
		SMD_TAG+="-e /SMDFILE/d ";
	fi
fi;


# EFI_TAG: Minimum FAT32 partition size is 64MiB (== 1 FAT cluster)
#
localefifile=efi.img;
efifs_size=$(( 64 * 1024 * 1024 ));
EFI_TAG+="-e s/EFISIZE/${efifs_size}/ ";
if [ "${bootloadername}" = "uefi.bin" ]; then
	build_fsimg $localefifile "" $efifs_size "FAT32" "" "$cmdline" "False";
	EFI_TAG+="-e s/EXI/EFI/ ";
	EFI_TAG+="-e s/EFIFILE/${localefifile}/ ";
else
	EFI_TAG+="-e /EFIFILE/d ";
fi;

# GPT_TAG: tag should created before cfg and actual img should be
#	   created after cfg.
#
localpptfile=ppt.img;
localsptfile=gpt.img;
if [ ! -z "${bootpartsize}" -a ! -z "${emmcsize}" ]; then
	bplmod=$(( ${bootpartlim} % ${devsectsize} ));
	if [ ${bplmod} -ne 0 ]; then
		echo "Error: Boot partition limit is not modulo ${devsectsize}";
		exit 1;
	fi;
	bpsmod=$(( ${bootpartsize} % ${devsectsize} ));
	if [ ${bpsmod} -ne 0 ]; then
		echo "Error: Boot partition size is not modulo ${devsectsize}";
		exit 1;
	fi;
	gptsize=$(( ${bootpartlim} - ${bootpartsize} ));
	if [ ${gptsize} -lt ${devsectsize} ]; then
		echo "Error: No space for primary GPT.";
		exit 1;
	fi;
	GPT_TAG+="-e s/PPTSIZE/${gptsize}/ ";
else
	GPT_TAG+="-e s/PPTSIZE/16896/ ";
fi;

# CBOOTOPTION_TAG:== Cboot option DTB
#
if [ "${cbootoptionfile}" != "" ]; then
	cp2local cbootoptionfile "${BL_DIR}/${cbootoptionfilename}";
	CBOOTOPTION_TAG="-e s/CBOOTOPTION_FILE/${cbootoptionfilename}/ ";
else
	CBOOTOPTION_TAG="-e /CBOOTOPTION_FILE/d ";
fi;

# CFG:
#
if [[ ${cfgfile} =~ \.xml$ ]]; then
	localcfgfile=flash.xml;
else
	localcfgfile=flash.cfg;
fi;
echo -n "copying cfgfile(${cfgfile}) to ${localcfgfile}... ";
if [ "${BINSARGS}" != "" ]; then
	# Close BINSARGS before get used for the first time.
	BINSARGS+="\"";
	BINSCONV+="-e s/\"[[:space:]]*/\"/ ";
	BINSCONV+="-e s/\;[[:space:]]*\"/\"/ ";
	BINSARGS=`echo "${BINSARGS}" | sed ${BINSCONV}`;
fi;
if [ "${T21BINARGS}" != "" ]; then
	# Close T21BINARGS before get used for the first time.
	T21BINARGS+="\"";
	BINSCONV=""
	BINSCONV+="-e s/\"[[:space:]]*/\"/ ";
	BINSCONV+="-e s/\;[[:space:]]*\"/\"/ ";
	T21BINARGS=`echo "${T21BINARGS}" | sed ${BINSCONV}`;
fi;
CFGCONV+="${EBT_TAG} ";
CFGCONV+="${LNX_TAG} ";
CFGCONV+="${SOS_TAG} ";
CFGCONV+="${NCT_TAG} ";
CFGCONV+="${VER_TAG} ";
CFGCONV+="${NVC_TAG} ";
CFGCONV+="${MB2BL_TAG} ";
CFGCONV+="${MPB_TAG} ";
CFGCONV+="${IST_TAG} ";
CFGCONV+="${MBP_TAG} ";
CFGCONV+="${MB1_TAG} ";
CFGCONV+="${BPFDTB_TAG} ";
CFGCONV+="${BPF_TAG} ";
CFGCONV+="${SCE_TAG} ";
CFGCONV+="${SPE_TAG} ";
CFGCONV+="${DRAMECC_TAG} ";
CFGCONV+="${BADPAGE_TAG} ";
CFGCONV+="${TOS_TAG} ";
CFGCONV+="${EKS_TAG} ";
CFGCONV+="${FB_TAG}  ";
CFGCONV+="${WB0_TAG} ";
CFGCONV+="${APP_TAG} ";
CFGCONV+="${EFI_TAG} ";
CFGCONV+="${DTB_TAG} ";
CFGCONV+="${TBCDTB_TAG} ";
CFGCONV+="${TBC_TAG} ";
CFGCONV+="${GPT_TAG} ";
CFGCONV+="${CBOOTOPTION_TAG} ";
CFGCONV+="${REC_TAG} ";
CFGCONV+="${RECDTB_TAG} ";
CFGCONV+="${BOOTCTRL_TAG} ";
CFGCONV+="${RECROOTFS_TAG} ";
CFGCONV+="${VARSTORE_TAG} ";
CFGCONV+="${SMD_TAG} ";

# CFGCONV is a flat string holding a bunch of flags for sed, so should not be
# quoted. Maybe need to convert CFGCONV to a list so that we can quote this.
# For now, though, disable SC2086.
cat "${cfgfile}" | sed ${CFGCONV} > ${localcfgfile}; chkerr;

# Sign image for RCM boot
if [ ${rcm_boot} -eq 1 ] && [ "${tegraid}" = "0x21" ]; then
	# update dtb to add board-id under plugin-manger node
	board_ids="${board_id}-${board_sku}-${board_version}"
	"${DTC}" -I dtb -O dts "${BL_DIR}"/${dtbfilename} -o temp.dts;
	# Below provided details on how "ids {\n ${board_ids};\n};" inserted under plugin-manager node:
	# 1. Limit the scope between "chosen {" and "plugin-manager {", if there is no plugin-manager,
	#    break(!b) else proceed, below code used:
	#	a. /chosen {/,/plugin-manager {/!b;/
	# 2. Go to pattern "plugin-manager {", if "plugin-manager {" pattern not found, break(!b)
	#    else read next line(n), if next line doesn't have "};" break else proceed, below code used:
	#	a. /plugin-manager {/!b;n;/}\;/!b;
	#3. Insert(i) ids under plugin-manager node(\t is for tab): ids {\n ${board_ids};\n};
	sed -i "/chosen {/,/plugin-manager {/!b;/plugin-manager {/!b;n;/}\;/!b;i \\\t\tids {\n\t\t\t${board_ids};\n\t\t\t};" temp.dts
	"${DTC}" -I dts -O dtb temp.dts -o ${BL_DIR}/${dtbfilename}; sync; rm temp.dts;

	echo "*** Signing images for rcm boot on t21x devices ***"
	t21x_sign_rcmboot_images
	t21x_prepare_rcmboot_args
fi

# GPT:
# mkgpt need to update as per new flash_t186_l4t.xml,
# currently skipping mkgpt as gpt partition is taken care by tegraflash.
if [ ! -z "${bootpartsize}" -a ! -z "${emmcsize}" -a \
    "${tegraid}" != "0x18" -a "${tegraid}" != "0x19" ]; then
	echo "creating gpt(${localpptfile})... ";
	MKGPTOPTS="-c ${localcfgfile} -P ${localpptfile} ";
	MKGPTOPTS+="-t ${emmcsize} -b ${bootpartsize} -s 4KiB ";
	MKGPTOPTS+="-a GPT -v GP1 ";
	MKGPTOPTS+="-V ${MKGPTCMD} ";
	./mkgpt ${MKGPTOPTS};
	chkerr "creating gpt(${localpptfile}) failed.";
fi;
# FLASH:
#
cp2local flasher	"${BL_DIR}/${flashername}";
cp2local flashapp	"${BL_DIR}/${flashappname}";

if [ "${target_partname}" != "" ]; then
	validatePartID target_partid target_partname $target_partname $localcfgfile;
	tmp_updateid="[${target_partname}]";
	need_sign=0;
	signtype="encrypt";
	if [ "${bootauth}" = "PKC" ] || [ "${bootauth}" = "SBKPKC" ]; then
		signtype="signed";
	fi;
	case ${target_partname} in
	BCT) target_partfile="${bctfilename}";
	     FLASHARGS="${BCT} ${target_partfile} --updatebct SDRAM ";
	     ;;
	mb2 | mb2_b) target_partfile="${tegrabootname}";
	     need_sign=1;
	     ;;
	bpmp-fw | bpmp-fw_b)
	     target_partfile="${bpffilename}";
	     need_sign=1;
	     ;;
	bpmp-fw-dtb | bpmp-fw-dtb_b)
	     target_partfile="${bpfdtbfilename}";
	     need_sign=1;
	     ;;
	PPT) target_partfile="${localpptfile}"; ;;
	EBT) target_partfile="${bootloadername}"; need_sign=1; ;;
	cpu-bootloader | cpu-bootloader_b)
	     target_partfile="${tbcfilename}";
	     need_sign=1;
	     ;;
	bootloader-dtb | bootloader-dtb_b)
	     target_partfile="${tbcdtbfilename}";
	     need_sign=1;
	     ;;
	secure-os | secure-os_b)
	     target_partfile="${tosfilename}";
	     need_sign=1;
	     ;;
	eks) target_partfile="${eksfilename}";
	     need_sign=1;
	     ;;
	LNX) target_partfile="${localbootfile}";
		if [ "${tegraid}" = "0x21" ]; then
			if [ "${read_part_name}" = "" ]; then
				need_sign=1;
			fi;
		else
			pre_cmds="write DTB ${dtbfilename}; ";
		fi;
		;;
	kernel | kernel_b)
	     target_partfile="${localbootfile}";
	     need_sign=1;
	     if [[ "${rootfs_ab}" == 1  && ${target_partname} == "kernel_b" ]]; then
		     target_partfile="${localbootfile}_b";
	     fi;
	     ;;
	kernel-dtb | kernel-dtb_b) target_partfile="${dtbfilename}";
	     need_sign=1;
	     ;;
	recovery-dtb)
		if [ "${tegraid}" = "0x18" ] || [ "${tegraid}" = "0x19" ]; then
			target_partfile="${recdtbfilename}";
			need_sign=1;
		else
			echo "Only T186 device supports this option"
			exit 1
		fi
		;;
	recovery)
		if [ "${tegraid}" = "0x18" ] || [ "${tegraid}" = "0x19" ]; then
			target_partfile="${localrecfile}";
			need_sign=1;
		else
			echo "Only T186 device supports this option"
			exit 1
		fi
		;;
	NCT) target_partfile="${nctfilename}"; ;;
	SOS) target_partfile="${sosfilename}"; ;;
	NVC) target_partfile="${tegrabootname}"; need_sign=1; ;;
	MPB) target_partfile="${mtsprebootname}"; ;;
	MBP) target_partfile="${mtsname}"; ;;
	BPF) target_partfile="${bpffilename}"; ;;
	APP)
		if [ ${disk_enc_enable} -eq 0 ]; then
			target_partfile="${localsysfile}";
		else
			target_partfile="${localsysbootfile}";
		fi;
		;;
	APP_b)
		if [ ${rootfs_ab} -eq 0 ]; then
			echo "*** Update APP_b is not supported. ***";
			echo "*** Set ROOTFS_AB=1 to enable APP_b. ***";
			exit 1;
		elif [ ${rootfs_ab} -eq 1 ] && [ ${disk_enc_enable} -eq 0 ]; then
			target_partfile="${localsysfile}_b";
		elif [ ${rootfs_ab} -eq 1 ] && [ ${disk_enc_enable} -eq 1 ]; then
			target_partfile="${localsysbootfile_b}";
		fi;
		;;
	APP_ENC)
		if [ ${disk_enc_enable} -eq 0 ]; then
			echo "*** Update APP_ENC is not supported. ***";
			echo "*** Set ROOTFS_ENC=1 to enable APP_ENC. ***";
			exit 1;
		else
			target_partfile="${localsysencrootfile}";
		fi
		;;
	APP_ENC_b)
		if [ ${disk_enc_enable} -eq 0 ] || [ ${rootfs_ab} -eq 0 ]; then
			echo "*** Update APP_ENC_b is not supported. ***";
			echo "*** Set ROOTFS_AB=1 & ROOTFS_ENC=1 to enable APP_ENC_b. ***";
			exit 1;
		else
			target_partfile="${localsysencrootfile_b}";
		fi
		;;
	DTB|RP1) target_partfile="${dtbfilename}";
		need_sign=1;
		;;
	EFI) target_partfile="${localefifile}"; ;;
	TOS) target_partfile="${tosfilename}"; ;;
	EKS) target_partfile="${eksfilename}"; ;;
	FB)  target_partfile="${fbfilename}"; ;;
	WB0) target_partfile="${wb0bootname}"; ;;
	GPT) target_partfile="${localsptfile}"; ;;
	rce-fw | rce-fw_b)
	     target_partfile="${camerafwname}";
	     need_sign=1;
	     ;;
	sce-fw | sce-fw_b)
	     target_partfile="${scefilename}";
	     need_sign=1;
	     ;;
	mts-preboot | mts-mce | mts-proper | \
	mts-preboot_b | mts-mce_b | mts-proper_b | \
	adsp-fw | extended-can-fw | \
	adsp-fw_b | extended-can-fw_b | \
	fusebypass)
	     # For partitions that do not have default image, user must provide
	     # the image to be flashed
	     if [ "${read_part_name}" = "" ] && [ "${write_image_name}" = "" ]; then
	         echo -n "*** Error: missing ${target_partname} image. ";
	         echo "Use option --image to specify the image to be flashed.";
	         exit 1;
	     fi;
	     need_sign=1;
	     ;;
	xusb-fw | xusb-fw_b | BMP | BMP_b)
	     if [ "${read_part_name}" = "" ] && [ "${write_image_name}" = "" ]; then
	         echo -n "*** Error: missing ${target_partname} image. ";
	         echo "Use option --image to specify the image to be flashed.";
	         exit 1;
	     fi;
	     ;;
	MB1_BCT | MB1_BCT_b)
		# use the name hard coded by tegraflash.py
		if [ "${read_part_name}" = "" ]; then
			write_image_name="signed/mb1_cold_boot_bct_MB1_sigheader.bct.${signtype}"
		fi;
		need_sign=1;
		;;
	#
	# Comment out sc7 support. It is found that sc7 sigheader is different and it needs special handling
	# See 200617500
	#
	# sc7 | sc7_b) target_partfile="${wb0bootname}";
	#	need_sign=1;
	#	;;
	spe-fw | spe-fw_b)
	     target_partfile="${spefilename}";
	     need_sign=1;
	     ;;
	CPUBL-CFG)
	     target_partfile="${cbootoptionfilename}";
	     ;;
	*)   echo "*** Update ${tmp_updateid} is not supported. ***";
	     exit 1; ;;
	esac;
	if [ "${read_part_name}" != "" ]; then
		# Read partition
		target_partfile="${read_part_name}";
		echo "*** Reading ${tmp_updateid} and storing to ${target_partfile} ***";
	else
		# Write partition
		if [ "${write_image_name}" != "" ]; then
			# write partition with image provided in command line
			target_partfile="${write_image_name}";
		fi;
		if [ ${no_flash} -eq 1 ]; then
			echo "*** Signing ${target_partfile} ***";
		else
			echo "*** Updating ${tmp_updateid} with ${target_partfile} ***";
		fi;
	fi;
	if [ "${FLASHARGS}" = "" ]; then
		FLASHARGS="--bl ${flashername} ${DTBARGS} ";
		if [ "${keyfile}" != "" -a "${tegraid}" = "0x21" ]; then
			FLASHARGS="--bl ${flashername}.signed ";
			DTBARGS+="--bldtb ${dtbfilename}.signed ";
		fi;
		if [ "${CHIPMAJOR}" != "" ]; then
			FLASHARGS+="--chip \"${tegraid} ${CHIPMAJOR}\" ";
		else
			FLASHARGS+="--chip ${tegraid} ";
		fi;
		FLASHARGS+="--applet ${sosfilename} ";
	fi;
	if [ "${CHIPID}" = "0x19" ]; then
		FLASHARGS+="$BCT ${bctfilename},${bctfile1name} ";
	else
		FLASHARGS+="$BCT ${bctfilename} ";
	fi

	# special handling for T210 due to signwrite command is not supported
	if [ ${need_sign} -eq 1 ]; then
		pf_dir="$(dirname "${target_partfile}")";
		pf_fn="$(basename "${target_partfile}")";
		if [ "${read_part_name}" != "" ]; then
			mkdir -p "${pf_dir}/signed" > /dev/null 2>&1;
		fi;
		if [ "${tegraid}" = "0x21" ]; then
			target_partfile="${pf_dir}/signed/${pf_fn}.${signtype}";
		fi;
	fi

	FLASHARGS+="${BCTARGS}${NV_ARGS} ";
	FLASHARGS+="--cfg  ${localcfgfile} ${BINSARGS} ";
	if [ "${CHIPID}" = "0x21" ] && [ "${bcffile}" != "" ]; then
		FLASHARGS+="--boardconfig ${bcffilename} ";
	fi
	FLASHARGS+=" --odmdata ${odmdata} ";
	FLASHARGS+=" --cmd \"";
	FLASHARGS+="${pre_cmds}";
	if [ "${read_part_name}" != "" ]; then
		FLASHARGS+="read ${target_partname} ${target_partfile}\" ";
	else
		# if target_partfile is not specified, exit with error message
		if [ "${target_partfile}" = "" ];then
			echo "*** Error: the file for writing ${target_partname} or signing is not specified. ****"
			exit 1
		fi
		if [ ${no_flash} -eq 1 ]; then
			FLASHARGS="--chip ${tegraid} --cmd \"sign ${target_partfile}\" ";
		else
			# Only issue erase command for QSPI device.
			# The sdmmc erase/trim operation may corrupt other partitions.
			# See 200565454 and 200615787
			if [[ "${ext_target_board_canonical}" == "p3509-0000+p3668"* ||
				"${ext_target_board_canonical}" == "p3448-0000-sd"* ||
				"${ext_target_board_canonical}" == "p3449-0000+p3448-0000-qspi"* ||
				"${ext_target_board_canonical}" == "p3448-0000-max-spi"* ]]; then
				# issue an erase command before write
				FLASHARGS+="erase ${target_partname}; ";
			fi

			if [ ${need_sign} -eq 1 ]; then
				# special handling for MB1_BCT and T210
				if [ "${target_partname}" = "MB1_BCT" ] ||
					[ "${target_partname}" = "MB1_BCT_b" ] ||
					[ "${tegraid}" = "0x21" ]; then
					FLASHARGS+="sign; write ";
				else
					FLASHARGS+="signwrite ";
				fi;
			else
				FLASHARGS+="write ";
			fi
			FLASHARGS+="${target_partname} ${target_partfile}; ";
			FLASHARGS+="reboot\" ";
		fi
	fi
	FLASHARGS+="${SKIPUID} ";
	if [ -n "${usb_instance}" ]; then
		FLASHARGS+="--instance ${usb_instance} ";
	fi;
	# Add keyfile if provided
	if [ "${keyfile}" != "" ]; then
		FLASHARGS+="--key \"${keyfile}\" ";
	fi;
	if [ "${RAMCODE}" != "" ]; then
		FLASHARGS+="--ramcode ${RAMCODE} ";
	fi;
	echo "./${flashappname} ${FLASHARGS}";
	cmd="./${flashappname} ${FLASHARGS}";
	eval ${cmd};
	chkerr "Failed to flash/read ${target_board}.";
	if [ "${read_part_name}" != "" ]; then
		#
		# Save signed image with .signed extension,
		#
		if [ ${need_sign} -eq 1 ]; then
			mv -f "${target_partfile}" "${target_partfile}.signed";
			# remove the sign header
			if [ "${CHIPID}" = "0x21" ]; then
				header_sz=600           # 0x258 bytes
			elif [ "${CHIPID}" = "0x18" ]; then
				header_sz=400           # 0x190 bytes
			elif [ "${CHIPID}" = "0x19" ]; then
				header_sz=4096           # 0x1000 bytes
			fi;
			dd if="${target_partfile}.signed" of="${target_partfile}" \
				bs="${header_sz}" skip=1
		fi;
		echo "*** The ${tmp_updateid} has been read successfully. ***";
		if [ "${target_partname}" = "APP" -a -x mksparse ]; then
			echo -e -n "\tConverting RAW image to Sparse image... ";
			mv -f ${target_partfile} ${target_partfile}.raw;
			./mksparse --fillpattern=0 ${target_partfile}.raw ${target_partfile};
		fi;
	else
		if [ ${no_flash} -eq 1 ]; then
			echo "*** ${target_partfile} has been signed successfully. ***";
		else
			echo "*** The ${tmp_updateid} has been updated successfully. ***";
		fi;
	fi;
	exit 0;
fi;

# Init flash args
FLASHARGS="";

if [ ${clean_up} -eq 0 ]; then
	# --clean_up is handled outside odmsign
	if [ -f odmsign.func ]; then
		source odmsign.func;
		odmsign_ext;
		if [ $? -ne 0 ]; then
			exit 1;
		fi;
	else
		if [ "${sbk_keyfile}" != "" ]; then
			# SBK is only handled by secure boot package
			echo "Error: missing secure boot package";
			exit 1;
		fi;
	fi;
fi;

if [ -n "${usb_instance}" ]; then
	FLASHARGS+="--instance ${usb_instance} ";
fi;
if [ "${tegraid}" = "0x21" ] && [ ${rcm_boot} -eq 1 ];then
	SOSARGS=""
	DTBARGS=""
	FLASHARGS+="--bl ${rcmflasher} ${BCT} ${rcmbctfile} ${T21RCMARGS} ";
else
	FLASHARGS+="--bl ${flashername} ${BCT} ${bctfilename}";
fi
if [ "${CHIPID}" = "0x19" ]; then
	FLASHARGS+=",${bctfile1name} ";
fi
FLASHARGS+=" --odmdata ${odmdata} ";
FLASHARGS+="${DTBARGS}${MTSARGS}${SOSARGS}${NCTARGS}${FBARGS}${NV_ARGS} ";
FLASHARGS+="--cfg ${localcfgfile} ";
if [ "${CHIPMAJOR}" != "" ]; then
	FLASHARGS+="--chip \"${tegraid} ${CHIPMAJOR}\" ";
else
	FLASHARGS+="--chip ${tegraid} ";
fi;
FLASHARGS+="${BCTARGS} ";
FLASHARGS+="${BINSARGS} ";
FLASHARGS+="${SKIPUID} ";
FLASHARGS+="${T21BINARGS} ";
if [ "$TRIM_BPMP_DTB" = "true" ]; then
	FLASHARGS+="--trim_bpmp_dtb ";
fi;
if [ "${external_device}" -eq 1 ] && [[ "${target_rootdev}" = "internal" || "${target_rootdev}" == "${BOOTDEV}" ]]; then
	FLASHARGS+="--external_device ";
fi

# Support PKC signing when flashing
if [ "${keyfile}" != "" ]; then
		FLASHARGS+=" --key \"${keyfile}\" ";
fi;

if [ "${RAMCODE}" != "" ]; then
	FLASHARGS+=" --ramcode ${RAMCODE} ";
fi;

flashcmd="./${flashappname} ${FLASHARGS}";
echo "${flashcmd}";
flashcmdfile="${BL_DIR}/flashcmd.txt";
echo "saving flash command in ${flashcmdfile}";
echo "${flashcmd}" > "${flashcmdfile}";
# Remove --skipuid flag for running flash command tegraflash.py directly
sed -i 's/--skipuid//g' "${flashcmdfile}"

# For Windows flashing or rcmboot
sata_boot_ext="sb"
rcm_boot_ext="rb"
kernel_dtb_file="kernel_dtb_filename.txt"
if [ ${rcm_boot} -eq 0 ]; then
	flashargfile="${BL_DIR}/flash_parameters.txt";
	cp -f ${localbootfile} ${localbootfile}.${sata_boot_ext};
	chkerr "Failed to copy boot image file ${localbootfile}.";
	cp -f ${localcfgfile} ${localcfgfile}.${sata_boot_ext};
	chkerr "Failed to copy partition layout file ${localcfgfile}.";
	cp -f ${dtbfilename} ${dtbfilename}.${sata_boot_ext};
	chkerr "Failed to copy kernel dtb file ${dtbfilename}.";
else
	flashargfile="${BL_DIR}/rcmboot_parameters.txt";
	cp -f ${localbootfile} ${localbootfile}.${rcm_boot_ext};
	chkerr "Failed to copy boot image file ${localbootfile}.";
	cp -f initrd initrd.${rcm_boot_ext};
	chkerr "Failed to copy initrd image file initrd.";
fi;
echo "${FLASHARGS}" > "${flashargfile}";
# Remove --skipuid flag for running flash command tegraflash.py directly
sed -i 's/--skipuid//g' "${flashargfile}"

# generate batch command for Windows flashing
flash_win_file="${BL_DIR}/flash_win.bat";
flash_win_cmd="python .\\win_tools\\${flashappname}"
echo "saving Windows flash command to ${flash_win_file}";
echo -n "${flash_win_cmd} " > "${flash_win_file}";
cat "${flashargfile}" >> "${flash_win_file}"

# generate crc32 header for t210 based partition table (pt) image
if [ "${CHIPID}" = "0x21" ]; then
	generate_pt_header
fi;

# generate bootloader update payload (BUP)
if [ ${bup_blob} -ne 0 ]; then
	bup_gen="${BL_DIR}/l4t_bup_gen.func"
	if [ -f "${bup_gen}" ]; then
		source "${bup_gen}"
		echo "*** Sign and generate BUP... *** ";
		if [ "${BOARDID}" = "" ]; then
			echo "Error: BOARDID is missing. BOARDID can be either set by "\
				"environment variable BOARDID or by reading from on-board "\
				"EEPROM."
			exit 1
		fi
		if [ "${fuselevel}" = "" ]; then
			echo "Error: fuselevel is missing."
			exit 1
		fi;
		if [ "${FAB}" = "" ]; then
			echo "Error: FAB # is missing."
			exit 1
		fi;
		l4t_bup_gen "${flashcmd}" "${spec}" "${fuselevel}" "${target_board}" \
			"${keyfile}" "${sbk_keyfile}" "${CHIPID}"
	else
		echo ""
		echo "Error: Missing ${bup_gen}"
		echo ""
		exit 1
	fi;
	exit 0;
fi;

if [ ${to_sign} -ne 0 ]; then
	echo "*** Sign and generate flashing ready partition images... *** ";
	eval "${flashcmd}";
	exit 0;
fi;

if [ ${no_flash} -ne 0 ]; then
	echo "*** no-flash flag enabled. Exiting now... *** ";
	exit 0;
fi;

echo "*** Flashing target device started. ***"
eval "${flashcmd}";
chkerr "Failed flashing ${target_board}.";
echo "*** The target ${target_board} has been flashed successfully. ***"
if [ "${rootdev_type}" = "internal" ]; then
	echo "Reset the board to boot from internal eMMC.";
elif [ "${rootdev_type}" = "network" ]; then
	if [ "${nfsroot}" != "" ]; then
		echo -n "Make target nfsroot(${nfsroot}) exported ";
		echo "on the network and reset the board to boot";
	else
		echo -n "Make the target nfsroot exported on the ";
		echo -n "network, configure your own DHCP server ";
		echo -n "with \"option-root=<nfsroot export path>;\" ";
		echo "properly and reset the board to boot";
	fi;
else
	echo -n "Make the target filesystem available to the device ";
	echo -n "and reset the board to boot from external ";
	echo "${target_rootdev}.";
fi;
echo;
exit 0;

# vi: ts=8 sw=8 noexpandtab
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
1722
1723
1724
1725
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739
1740
1741
1742
1743
1744
1745
1746
1747
1748
1749
1750
1751
1752
1753
1754
1755
1756
1757
1758
1759
1760
1761
1762
1763
1764
1765
1766
1767
1768
1769
1770
1771
1772
1773
1774
1775
1776
1777
1778
1779
1780
1781
1782
1783
1784
1785
1786
1787
1788
1789
1790
1791
1792
1793
1794
1795
1796
1797
1798
1799
1800
1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811
1812
1813
1814
1815
1816
1817
1818
1819
1820
1821
1822
1823
1824
1825
1826
1827
1828
1829
1830
1831
1832
1833
1834
1835
1836
1837
1838
1839
1840
1841
1842
1843
1844
1845
1846
1847
1848
1849
1850
1851
1852
1853
1854
1855
1856
1857
1858
1859
1860
1861
1862
1863
1864
1865
1866
1867
1868
1869
1870
1871
1872
1873
1874
1875
1876
1877
1878
1879
1880
1881
1882
1883
1884
1885
1886
1887
1888
1889
1890
1891
1892
1893
1894
1895
1896
1897
1898
1899
1900
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
1911
1912
1913
1914
1915
1916
1917
1918
1919
1920
1921
1922
1923
1924
1925
1926
1927
1928
1929
1930
1931
1932
1933
1934
1935
1936
1937
1938
1939
1940
1941
1942
1943
1944
1945
1946
1947
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
2025
2026
2027
2028
2029
2030
2031
2032
2033
2034
2035
2036
2037
2038
2039
2040
2041
2042
2043
2044
2045
2046
2047
2048
2049
2050
2051
2052
2053
2054
2055
2056
2057
2058
2059
2060
2061
2062
2063
2064
2065
2066
2067
2068
2069
2070
2071
2072
2073
2074
2075
2076
2077
2078
2079
2080
2081
2082
2083
2084
2085
2086
2087
2088
2089
2090
2091
2092
2093
2094
2095
2096
2097
2098
2099
2100
2101
2102
2103
2104
2105
2106
2107
2108
2109
2110
2111
2112
2113
2114
2115
2116
2117
2118
2119
2120
2121
2122
2123
2124
2125
2126
2127
2128
2129
2130
2131
2132
2133
2134
2135
2136
2137
2138
2139
2140
2141
2142
2143
2144
2145
2146
2147
2148
2149
2150
2151
2152
2153
2154
2155
2156
2157
2158
2159
2160
2161
2162
2163
2164
2165
2166
2167
2168
2169
2170
2171
2172
2173
2174
2175
2176
2177
2178
2179
2180
2181
2182
2183
2184
2185
2186
2187
2188
2189
2190
2191
2192
2193
2194
2195
2196
2197
2198
2199
2200
2201
2202
2203
2204
2205
2206
2207
2208
2209
2210
2211
2212
2213
2214
2215
2216
2217
2218
2219
2220
2221
2222
2223
2224
2225
2226
2227
2228
2229
2230
2231
2232
2233
2234
2235
2236
2237
2238
2239
2240
2241
2242
2243
2244
2245
2246
2247
2248
2249
2250
2251
2252
2253
2254
2255
2256
2257
2258
2259
2260
2261
2262
2263
2264
2265
2266
2267
2268
2269
2270
2271
2272
2273
2274
2275
2276
2277
2278
2279
2280
2281
2282
2283
2284
2285
2286
2287
2288
2289
2290
2291
2292
2293
2294
2295
2296
2297
2298
2299
2300
2301
2302
2303
2304
2305
2306
2307
2308
2309
2310
2311
2312
2313
2314
2315
2316
2317
2318
2319
2320
2321
2322
2323
2324
2325
2326
2327
2328
2329
2330
2331
2332
2333
2334
2335
2336
2337
2338
2339
2340
2341
2342
2343
2344
2345
2346
2347
2348
2349
2350
2351
2352
2353
2354
2355
2356
2357
2358
2359
2360
2361
2362
2363
2364
2365
2366
2367
2368
2369
2370
2371
2372
2373
2374
2375
2376
2377
2378
2379
2380
2381
2382
2383
2384
2385
2386
2387
2388
2389
2390
2391
2392
2393
2394
2395
2396
2397
2398
2399
2400
2401
2402
2403
2404
2405
2406
2407
2408
2409
2410
2411
2412
2413
2414
2415
2416
2417
2418
2419
2420
2421
2422
2423
2424
2425
2426
2427
2428
2429
2430
2431
2432
2433
2434
2435
2436
2437
2438
2439
2440
2441
2442
2443
2444
2445
2446
2447
2448
2449
2450
2451
2452
2453
2454
2455
2456
2457
2458
2459
2460
2461
2462
2463
2464
2465
2466
2467
2468
2469
2470
2471
2472
2473
2474
2475
2476
2477
2478
2479
2480
2481
2482
2483
2484
2485
2486
2487
2488
2489
2490
2491
2492
2493
2494
2495
2496
2497
2498
2499
2500
2501
2502
2503
2504
2505
2506
2507
2508
2509
2510
2511
2512
2513
2514
2515
2516
2517
2518
2519
2520
2521
2522
2523
2524
2525
2526
2527
2528
2529
2530
2531
2532
2533
2534
2535
2536
2537
2538
2539
2540
2541
2542
2543
2544
2545
2546
2547
2548
2549
2550
2551
2552
2553
2554
2555
2556
2557
2558
2559
2560
2561
2562
2563
2564
2565
2566
2567
2568
2569
2570
2571
2572
2573
2574
2575
2576
2577
2578
2579
2580
2581
2582
2583
2584
2585
2586
2587
2588
2589
2590
2591
2592
2593
2594
2595
2596
2597
2598
2599
2600
2601
2602
2603
2604
2605
2606
2607
2608
2609
2610
2611
2612
2613
2614
2615
2616
2617
2618
2619
2620
2621
2622
2623
2624
2625
2626
2627
2628
2629
2630
2631
2632
2633
2634
2635
2636
2637
2638
2639
2640
2641
2642
2643
2644
2645
2646
2647
2648
2649
2650
2651
2652
2653
2654
2655
2656
2657
2658
2659
2660
2661
2662
2663
2664
2665
2666
2667
2668
2669
2670
2671
2672
2673
2674
2675
2676
2677
2678
2679
2680
2681
2682
2683
2684
2685
2686
2687
2688
2689
2690
2691
2692
2693
2694
2695
2696
2697
2698
2699
2700
2701
2702
2703
2704
2705
2706
2707
2708
2709
2710
2711
2712
2713
2714
2715
2716
2717
2718
2719
2720
2721
2722
2723
2724
2725
2726
2727
2728
2729
2730
2731
2732
2733
2734
2735
2736
2737
2738
2739
2740
2741
2742
2743
2744
2745
2746
2747
2748
2749
2750
2751
2752
2753
2754
2755
2756
2757
2758
2759
2760
2761
2762
2763
2764
2765
2766
2767
2768
2769
2770
2771
2772
2773
2774
2775
2776
2777
2778
2779
2780
2781
2782
2783
2784
2785
2786
2787
2788
2789
2790
2791
2792
2793
2794
2795
2796
2797
2798
2799
2800
2801
2802
2803
2804
2805
2806
2807
2808
2809
2810
2811
2812
2813
2814
2815
2816
2817
2818
2819
2820
2821
2822
2823
2824
2825
2826
2827
2828
2829
2830
2831
2832
2833
2834
2835
2836
2837
2838
2839
2840
2841
2842
2843
2844
2845
2846
2847
2848
2849
2850
2851
2852
2853
2854
2855
2856
2857
2858
2859
2860
2861
2862
2863
2864
2865
2866
2867
2868
2869
2870
2871
2872
2873
2874
2875
2876
2877
2878
2879
2880
2881
2882
2883
2884
2885
2886
2887
2888
2889
2890
2891
2892
2893
2894
2895
2896
2897
2898
2899
2900
2901
2902
2903
2904
2905
2906
2907
2908
2909
2910
2911
2912
2913
2914
2915
2916
2917
2918
2919
2920
2921
2922
2923
2924
2925
2926
2927
2928
2929
2930
2931
2932
2933
2934
2935
2936
2937
2938
2939
2940
2941
2942
2943
2944
2945
2946
2947
2948
2949
2950
2951
2952
2953
2954
2955
2956
2957
2958
2959
2960
2961
2962
2963
2964
2965
2966
2967
2968
2969
2970
2971
2972
2973
2974
2975
2976
2977
2978
2979
2980
2981
2982
2983
2984
2985
2986
2987
2988
2989
2990
2991
2992
2993
2994
2995
2996
2997
2998
2999
3000
3001
3002
3003
3004
3005
3006
3007
3008
3009
3010
3011
3012
3013
3014
3015
3016
3017
3018
3019
3020
3021
3022
3023
3024
3025
3026
3027
3028
3029
3030
3031
3032
3033
3034
3035
3036
3037
3038
3039
3040
3041
3042
3043
3044
3045
3046
3047
3048
3049
3050
3051
3052
3053
3054
3055
3056
3057
3058
3059
3060
3061
3062
3063
3064
3065
3066
3067
3068
3069
3070
3071
3072
3073
3074
3075
3076
3077
3078
3079
3080
3081
3082
3083
3084
3085
3086
3087
3088
3089
3090
3091
3092
3093
3094
3095
3096
3097
3098
3099
3100
3101
3102
3103
3104
3105
3106
3107
3108
3109
3110
3111
3112
3113
3114
3115
3116
3117
3118
3119
3120
3121
3122
3123
3124
3125
3126
3127
3128
3129
3130
3131
3132
3133
3134
3135
3136
3137
3138
3139
3140
3141
3142
3143
3144
3145
3146
3147
3148
3149
3150
3151
3152
3153
3154
3155
3156
3157
3158
3159
3160
3161
3162
3163
3164
3165
3166
3167
3168
3169
3170
3171
3172
3173
3174
3175
3176
3177
3178
3179
3180
3181
3182
3183
3184
3185
3186
3187
3188
3189
3190
3191
3192
3193
3194
3195
3196
3197
3198
3199
3200
3201
3202
3203
3204
3205
3206
3207
3208
3209
3210
3211
3212
3213
3214
3215
3216
3217
3218
3219
3220
3221
3222
3223
3224
3225
3226
3227
3228
3229
3230
3231
3232
3233
3234
3235
3236
3237
3238
3239
3240
3241
3242
3243
3244
3245
3246
3247
3248
3249
3250
3251
3252
3253
3254
3255
3256
3257
3258
3259
3260
3261
3262
3263
3264
3265
3266
3267
3268
3269
3270
3271
3272
3273
3274
3275
3276
3277
3278
3279
3280
3281
3282
3283
3284
3285
3286
3287
3288
3289
3290
3291
3292
3293
3294
3295
3296
3297
3298
3299
3300
3301
3302
3303
3304
3305
3306
3307
3308
3309
3310
3311
3312
3313
3314
3315
3316
3317
3318
3319
3320
3321
3322
3323
3324
3325
3326
3327
3328
3329
3330
3331
3332
3333
3334
3335
3336
3337
3338
3339
3340
3341
3342
3343
3344
3345
3346
3347
3348
3349
3350
3351
3352
3353
3354
3355
3356
3357
3358
3359
3360
3361
3362
3363
3364
3365
3366
3367
3368
3369
3370
3371
3372
3373
3374
3375
3376
3377
3378
3379
3380
3381
3382
3383
3384
3385
3386
3387
3388
3389
3390
3391
3392
3393
3394
3395
3396
3397
3398
3399
3400
3401
3402
3403
3404
3405
3406
3407
3408
3409
3410
3411
3412
3413
3414
3415
3416
3417
3418
3419
3420
3421
3422
3423
3424
3425
3426
3427
3428
3429
3430
3431
3432
3433
3434
3435
3436
3437
3438
3439
3440
3441
3442
3443
3444
3445
3446
3447
3448
3449
3450
3451
3452
3453
3454
3455
3456
3457
3458
3459
3460