合宙ESP32S3 CameraWebServe 测试demo_camerawebserver详解

合宙ESP32S3 CameraWebServe

合宙ESP32S3 CameraWebServe测试，我们需要一个OV2640的摄像头模组用来采集图像传输给ESP32的，这里使用的OV2640是之前安信可十周年的白嫖的。现在直接插到合宙ESP32S3开发板，简直完美。还是白嫖好！！！

ESP32S3

合宙ESP32S3核心板是基于乐鑫ESP32-S3进行设计的一款核心板，尺寸仅有21mm*51mm，板边采用邮票孔设计，方便开发者在不同场景下的使用。核心板板载2.4G天线，支持wifi和蓝牙。核心板内置8MB psram，16MB flash豪华配置。板载ch343p USB转串口芯片，方便下载烧录；同时还设计了模拟开关电路，可一键切换到S3内置的USB，进行USB功能的开发调试。核心板支持UART、GPIO、SPI、I2C、ADC、PWM，SDIO，Camera等接口，可根据实际需要连接外设进行调试。

硬件资源

ESP32S3采用Xtensa® 32 位 LX7 双核处理器，五级流水线架构，主频高达240M。内置512K SRAM，本次发布型号和封8MB psram。

4 × SPI

1 × LCD 接口（8 位 ~16 位并行 RGB, I8080, MOTO6800）, 支持 RGB565, YUV422, YUV420, YUV411 之间互相转换

1 × DVP 8 位 ~16 位摄像头接口

3 × UART

2 × I2C

2 × I2S

1 × RMT (TX/RX)

1 × 脉冲计数器 – LED PWM 控制器，多达 8 个通道

1 × 全速 USB OTG

1 × USB Serial/JTAG 控制器

2 × MCPWM

1 × SDIO 主机接口，具有 2 个卡槽

通用 DMA 控制器 (简称 GDMA)，5 个接收通 道和 5 个发送通道

1 × TWAI® 控制器，兼容 ISO 11898-1（CAN 规范 2.0）

2 × 12 位 SAR ADC，多达 20 个通道

引脚分布

CameraWebServe测试demo

ArduinoIDE 开发esp32s3 参考流程
https://blog.csdn.net/chilian12321/article/details/115979076
准备好最主要的控制器模块之后我们需要一个OV2640的摄像头模组用来采集图像传输给ESP32的，这里使用的OV2640是之前安信可十周年的白嫖的。现在直接插到合宙ESP32S3开发板，简直完美。

code

#include "esp_camera.h"
#include <WiFi.h>

//
// WARNING!!! PSRAM IC required for UXGA resolution and high JPEG quality
//            Ensure ESP32 Wrover Module or other board with PSRAM is selected
//            Partial images will be transmitted if image exceeds buffer size
//
//            You must select partition scheme from the board menu that has at least 3MB APP space.
//            Face Recognition is DISABLED for ESP32 and ESP32-S2, because it takes up from 15 
//            seconds to process single frame. Face Detection is ENABLED if PSRAM is enabled as well

// ===================
// Select camera model
// ===================
//#define CAMERA_MODEL_WROVER_KIT // Has PSRAM
//#define CAMERA_MODEL_ESP_EYE // Has PSRAM
#define CAMERA_MODEL_ESP32S3_EYE // Has PSRAM
//#define CAMERA_MODEL_M5STACK_PSRAM // Has PSRAM
//#define CAMERA_MODEL_M5STACK_V2_PSRAM // M5Camera version B Has PSRAM
//#define CAMERA_MODEL_M5STACK_WIDE // Has PSRAM
//#define CAMERA_MODEL_M5STACK_ESP32CAM // No PSRAM
//#define CAMERA_MODEL_M5STACK_UNITCAM // No PSRAM
//#define CAMERA_MODEL_AI_THINKER // Has PSRAM
//#define CAMERA_MODEL_TTGO_T_JOURNAL // No PSRAM
// ** Espressif Internal Boards **
//#define CAMERA_MODEL_ESP32_CAM_BOARD
//#define CAMERA_MODEL_ESP32S2_CAM_BOARD
//#define CAMERA_MODEL_ESP32S3_CAM_LCD


#include "camera_pins.h"

// ===========================
// Enter your WiFi credentials  设置热点密码，唯一需要改动的部分
// ===========================
const char* ssid = "DAP";
const char* password = "delehub2023";

void startCameraServer();

void setup() {
  Serial.begin(115200);
  Serial.setDebugOutput(true);
  Serial.println();

  camera_config_t config;
  config.ledc_channel = LEDC_CHANNEL_0;
  config.ledc_timer = LEDC_TIMER_0;
  config.pin_d0 = Y2_GPIO_NUM;
  config.pin_d1 = Y3_GPIO_NUM;
  config.pin_d2 = Y4_GPIO_NUM;
  config.pin_d3 = Y5_GPIO_NUM;
  config.pin_d4 = Y6_GPIO_NUM;
  config.pin_d5 = Y7_GPIO_NUM;
  config.pin_d6 = Y8_GPIO_NUM;
  config.pin_d7 = Y9_GPIO_NUM;
  config.pin_xclk = XCLK_GPIO_NUM;
  config.pin_pclk = PCLK_GPIO_NUM;
  config.pin_vsync = VSYNC_GPIO_NUM;
  config.pin_href = HREF_GPIO_NUM;
  config.pin_sscb_sda = SIOD_GPIO_NUM;
  config.pin_sscb_scl = SIOC_GPIO_NUM;
  config.pin_pwdn = PWDN_GPIO_NUM;
  config.pin_reset = RESET_GPIO_NUM;
  config.xclk_freq_hz = 20000000;
  config.frame_size = FRAMESIZE_UXGA;
  config.pixel_format = PIXFORMAT_JPEG; // for streaming
  //config.pixel_format = PIXFORMAT_RGB565; // for face detection/recognition
  config.grab_mode = CAMERA_GRAB_WHEN_EMPTY;
  config.fb_location = CAMERA_FB_IN_PSRAM;
  config.jpeg_quality = 12;
  config.fb_count = 1;
  
  // if PSRAM IC present, init with UXGA resolution and higher JPEG quality
  //                      for larger pre-allocated frame buffer.
  if(config.pixel_format == PIXFORMAT_JPEG){
    if(psramFound()){
      config.jpeg_quality = 10;
      config.fb_count = 2;
      config.grab_mode = CAMERA_GRAB_LATEST;
    } else {
      // Limit the frame size when PSRAM is not available
      config.frame_size = FRAMESIZE_SVGA;
      config.fb_location = CAMERA_FB_IN_DRAM;
    }
  } else {
    // Best option for face detection/recognition
    config.frame_size = FRAMESIZE_240X240;
#if CONFIG_IDF_TARGET_ESP32S3
    config.fb_count = 2;
#endif
  }

#if defined(CAMERA_MODEL_ESP_EYE)
  pinMode(13, INPUT_PULLUP);
  pinMode(14, INPUT_PULLUP);
#endif

  // camera init
  esp_err_t err = esp_camera_init(&config);
  if (err != ESP_OK) {
    Serial.printf("Camera init failed with error 0x%x", err);
    return;
  }

  sensor_t * s = esp_camera_sensor_get();
  // initial sensors are flipped vertically and colors are a bit saturated
  if (s->id.PID == OV3660_PID) {
    s->set_vflip(s, 1); // flip it back
    s->set_brightness(s, 1); // up the brightness just a bit
    s->set_saturation(s, -2); // lower the saturation
  }
  // drop down frame size for higher initial frame rate
  if(config.pixel_format == PIXFORMAT_JPEG){
    s->set_framesize(s, FRAMESIZE_QVGA);
  }

#if defined(CAMERA_MODEL_M5STACK_WIDE) || defined(CAMERA_MODEL_M5STACK_ESP32CAM)
  s->set_vflip(s, 1);
  s->set_hmirror(s, 1);
#endif

#if defined(CAMERA_MODEL_ESP32S3_EYE)
  s->set_vflip(s, 1);
#endif

  WiFi.begin(ssid, password);
  WiFi.setSleep(false);

  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.println("WiFi connected");

  startCameraServer();

  Serial.print("Camera Ready! Use 'http://");
  Serial.print(WiFi.localIP());
  Serial.println("' to connect");
}

void loop() {
  // Do nothing. Everything is done in another task by the web server
  delay(10000);
}
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148

效果

1. 通过arduino 下载程序即可，下载配置
2. 通过串口助手查看服务器IP，正常连接，按下rst可查看
3. 通过浏览器，输入IP地址，打开界面
   

使用flash_download_tool_ 直接下载bin文件

有点问题。。。

代码参考地址

代码参考地址：https://gitee.com/ryzen123/arduino-esp32-CameraWebServer