default_settings.txt_deforum_settings.txt

# # Default settings for the simulation # ## Scenario settings Scenario.name = default_scenario Scenario.simulateConnections = true Scenario.updateInterval = 0.1 # 43k ~= 12h Scenario.endTime = 43k Scenario.nrofHostGroups = 6 ## Group-specific settings: # groupID : Group's identifier. Used as the prefix of host names # nrofHosts: number of hosts in the group # transmitRange: range of the hosts' radio devices (meters) # transmitSpeed: transmit speed of the radio devices (bytes per second) # movementModel: movement model of the hosts (valid class name from movement package) # waitTime: minimum and maximum wait times (seconds) after reaching destination # speed: minimum and maximum speeds (m/s) when moving on a path # bufferSize: size of the message buffer (bytes) # router: router used to route messages (valid class name from routing package) # activeTimes: Time intervals when the nodes in the group are active (start1, end1, start2, end2, ...) # msgTtl : TTL (minutes) of the messages created by this host group, default=infinite ## Group and movement model specific settings # pois: Points Of Interest indexes and probabilities (poiIndex1, poiProb1, poiIndex2, poiProb2, ... ) - for ShortestPathMapBasedMovement # okMaps : which map nodes are OK for the group (map file indexes), default=all - for all MapBasedMovent models # routeFile: route's file path - for MapRouteMovement # routeType: route's type - for MapRouteMovement # common settings for all groups Group.movementModel = ShortestPathMapBasedMovement Group.router = PassiveRouter Group.bufferSize = 5M Group.transmitRange = 10 # transmit speed of 2 Mbps = 250kBps Group.transmitSpeed = 250k Group.waitTime = 0, 120 # walking speeds Group.speed = 0.5, 1.5 #Group.msgTtl = 60 Group.nrofHosts = 40 # group1 (pedestrians) specific settings Group1.groupID = p # group2 specific settings Group2.groupID = c # cars can drive only on roads Group2.okMaps = 1 # 10-50 km/h Group2.speed = 2.7, 13.9 # another group of pedestrians Group3.groupID = w # The Tram groups Group4.groupID = t Group4.bufferSize = 50M Group4.movementModel = MapRouteMovement Group4.routeFile = data/tram3.wkt Group4.routeType = 1 Group4.waitTime = 10, 30 Group4.speed = 7, 10 Group4.nrofHosts = 2 Group5.groupID = t Group5.bufferSize = 50M Group5.movementModel = MapRouteMovement Group5.routeFile = data/tram4.wkt Group5.routeType = 2 Group5.waitTime = 10, 30 Group5.speed = 7, 10 Group5.nrofHosts = 2 Group6.groupID = t Group6.bufferSize = 50M Group6.movementModel = MapRouteMovement Group6.routeFile = data/tram10.wkt Group6.routeType = 2 Group6.waitTime = 10, 30 Group6.speed = 7, 10 Group6.nrofHosts = 2 ## Message creation parameters # How many event generators Events.nrof = 1 # Class of the first event generator Events1.class = MessageEventGenerator # (following settings are specific for the MessageEventGenerator class) # Creation interval in seconds (one new message every 25 to 35 seconds) Events1.interval = 25,35 # Message sizes (500kB - 1MB) Events1.size = 500k, 1M # range of message source/destination addresses Events1.hosts = 0,125 # Message ID prefix Events1.prefix = M ## Movement model settings # seed for movement models' pseudo random number generator (default = 0) MovementModel.rngSeed = 1 # World's size for Movement Models without implicit size (width, height; meters) MovementModel.worldSize = 4500, 3400 # How long time to move hosts in the world before real simulation MovementModel.warmup = 1000 ## Map based movement -movement model specific settings MapBasedMovement.nrofMapFiles = 4 MapBasedMovement.mapFile1 = data/roads.wkt MapBasedMovement.mapFile2 = data/main_roads.wkt MapBasedMovement.mapFile3 = data/pedestrian_paths.wkt MapBasedMovement.mapFile4 = data/shops.wkt ## Points Of Interest -specific settings PointsOfInterest.poiFile1 = data/ParkPOIs.wkt PointsOfInterest.poiFile2 = data/CentralPOIs.wkt PointsOfInterest.poiFile3 = data/WestPOIs.wkt PointsOfInterest.poiFile4 = data/shops.wkt ## Reports - all report names have to be valid report classes # how many reports to load Report.nrofReports = 1 # length of the warm up period (simulated seconds) Report.warmup = 0 # default directory of reports (can be overridden per Report with output setting) Report.reportDir = reports/ # Report classes to load Report.report1 = MessageStatsReport ## Default settings for some routers settings ProphetRouter.secondsInTimeUnit = 30 SprayAndWaitRouter.nrofCopies = 6 SprayAndWaitRouter.binaryMode = true ## Optimization settings -- these affect the speed of the simulation ## see World class for details. Optimization.connectionAlg = 2 Optimization.cellSizeMult = 5 Optimization.randomizeUpdateOrder = true ## GUI settings # GUI underlay image settings GUI.UnderlayImage.fileName = data/helsinki_underlay.png # Image offset in pixels (x, y) GUI.UnderlayImage.offset = 64, 20 # Scaling factor for the image GUI.UnderlayImage.scale = 4.75 # Image rotation (radians) GUI.UnderlayImage.rotate = -0.015 # how many events to show in the log panel (default = 30) GUI.EventLogPanel.nrofEvents = 30 # Regular Expression log filter (see Pattern-class from the Java API for RE-matching details) #GUI.EventLogPanel.REfilter = .*p[1-9]<->p[1-9]$