华为交换机万兆线缆堆叠_交换机堆叠线英文怎么说

华为交换机万兆线缆堆叠

两台华为S5730S-68C-EI-AC做堆叠：
将Master设备业务先配置好(略)。

Master配置：
[core]display stack configuration      #先查看默认配置
* : Invalid-configuration
# : Unsaved configuration
---------------Configuration on slot 0 Begin---------------
stack enable
stack slot 0 renumber 0      #slot ID
stack slot 0 priority 100      #优先级，越大越优先
stack reserved-vlan 4093
stack timer mac-address switch-delay 10

interface stack-port 0/1

interface stack-port 0/2
---------------Configuration on slot 0 End-----------------

---

#将物理端口关闭
[core]interface range XGigabitEthernet 0/0/1 to XGigabitEthernet 0/0/2
[core-XGigabitEthernet0/0/1]shutdown
[core-XGigabitEthernet0/0/2]shutdown
[core-port-group]quit

[core]interface stack-port 0/1
[core-stack-port0/1]port interface XGigabitEthernet 0/0/1 enable
[core-stack-port0/1]interface stack-port 0/2
[core-stack-port0/2]port interface XGigabitEthernet 0/0/2 enable
[core-stack-port0/2]quit
<core>save

Slave配置：
[HUAWEI]stack slot 0 renumber 1
[HUAWEI]stack slot 0 priority 10

[HUAWEI]interface range XGigabitEthernet 0/0/1 to XGigabitEthernet 0/0/2
[HUAWEI-XGigabitEthernet0/0/1]shutdown
[HUAWEI-XGigabitEthernet0/0/2]shutdown
[HUAWEI-port-group]quit

[HUAWEI]interface stack-port 0/1
[HUAWEI-stack-port0/1]port interface XGigabitEthernet 0/0/1 enable
[HUAWEI-stack-port0/1]interface stack-port 0/2
[HUAWEI-stack-port0/2]port interface XGigabitEthernet 0/0/2 enable
[HUAWEI-stack-port0/2]quit
[HUAWEI]
<HUAWEI>save

两台交换机配置保存后将XGe0/0/1和XGe0/0/2交叉互联，等待几分钟。备机重启完毕后堆叠自动完成。
[core]display stack
Stack mode: Service-port
Stack topology type: Ring
Stack system MAC: f41d-6bfa-afa0
MAC switch delay time: 10 min
Stack reserved VLAN: 4093
Slot of the active management port: –
Slot Role MAC Address Priority Device Type
-------------------------------------------------------------
0 Master f41d-6bfa-afa0 100 S5730S-68C-EI-AC
1 Standby f41d-6bfa-ac90 10 S5730S-68C-EI-AC
[core]

MAD检测：

[core]interface GigabitEthernet 0/0/48
[core-GigabitEthernet0/0/48]mad detect mode direct
[core-GigabitEthernet0/0/48]quit
[core]interface GigabitEthernet 0/0/48
[core-GigabitEthernet1/0/48]mad detect mode direct
<core>save
Ge0/0/48和Ge1/0/48网线直连即可

[core]display mad verbose
Current MAD domain: 0
Current MAD status: Detect
Mad direct detect interfaces configured:
GigabitEthernet0/0/48
GigabitEthernet1/0/48
Mad relay detect interfaces configured:
Excluded ports(configurable):
Excluded ports(can not be configured):
XGigabitEthernet0/0/1
XGigabitEthernet0/0/2
XGigabitEthernet1/0/1
XGigabitEthernet1/0/2

已测试堆叠分裂后slave设备除了stack口外，其他端口全部down

---

拆分stack

[core]interface stack-port 0/1
[core-stack-port0/1]shutdown interface XGigabitEthernet0/0/1      #需要首先关闭端口
[core-stack-port0/1]undo port interface XGigabitEthernet0/0/1 enable
[core-stack-port0/1]quit
[core]interface stack-port 0/2
[core-stack-port0/2]shutdown interface XGigabitEthernet0/0/2
[core-stack-port0/2]undo port interface XGigabitEthernet0/0/2 enable
[core-stack-port0/2]quit
<core>save
————————————————
版权声明：本文为CSDN博主「zdl244」的原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接及本声明。
原文链接：https://blog.csdn.net/zdl244/article/details/103174885