devbox
Gausst松鼠会
这个屌丝很懒，什么也没留下！
关注作者
热门标签
热门文章
当前位置:   article > 正文

华为配置WDS手拉手业务示例

作者：Gausst松鼠会 | 2024-02-29 19:04:16

赞

踩

华为配置WDS手拉手业务示例

配置WDS手拉手业务示例

组网图形

图1 配置WDS手拉手业务示例组网图
  • 业务需求
  • 组网需求
  • 数据规划
  • 配置思路
  • 配置注意事项
  • 操作步骤
  • 配置文件
业务需求

企业用户通过WLAN接入网络，以满足移动办公的最基本需求。但企业考虑到AP通过有线部署的成本较高，所以通过建立WDS无线桥接链路做无线回传，用于部署业务覆盖，保证企业用户可以接入无线网络。

组网需求
  • AC组网方式：旁挂二层组网。
  • DHCP部署方式：
    • AC作为DHCP服务器为AP分配IP地址。
    • 汇聚交换机Switch_A作为DHCP服务器为STA分配IP地址。
  • 无线回传方式：WDS手拉手方式。
  • 回传射频：5G频段。
  • 业务数据转发方式：直接转发。
数据规划
表1 AP数据规划表

AP

类型

MAC

AP_1

AP8130DN

60de-4474-9640

AP_2

AP8130DN

dcd2-fc04-b500

AP_3

AP8130DN

dcd2-fc96-e4c0

表2 AC数据规划表

配置项

数据

AP管理VLAN

VLAN100

STA业务VLAN

VLAN101

DHCP服务器

AC作为AP的DHCP服务器，Switch_A作为STA的DHCP服务器。

AP地址池

10.23.100.2～10.23.100.254/24

STA地址池

10.23.101.3～10.23.101.254/24

AC源接口

VLANIF100

WDS角色
  • AP_1射频1：root
  • AP_2射频1：leaf
  • AP_2射频0：root
  • AP_3射频1：leaf

域管理模板
  • 名称：default
  • 国家码：中国

SSID模板
  • 名称：wlan-net
  • SSID名称：wlan-net

WLAN无线业务安全模板
  • 名称：wlan-net
  • 安全策略：WPA-WPA2+PSK+AES
  • 密码：a1234567

VAP模板
  • 名称：wlan-net
  • 转发模式：直接转发
  • 业务VLAN：VLAN101
  • 引用模板：SSID模板wlan-net、安全模板wlan-net

WDS链路安全模板

  • 名称：wds-security

  • 安全策略：WPA2+PSK+AES

  • 密码类型：PASS-PHRASE

  • 密码：a1234567

WDS白名单模板

  • 名称：wds-list1

  • AP MAC地址：AP_2 leaf节点的MAC地址

  • 名称：wds-list2

  • AP MAC地址：AP_3 leaf节点的MAC地址

WDS模板

  • 名称：wds-root

  • WDS网桥名称：wlan-wds

  • WDS工作模式：root

  • Tagged VLAN：VLAN101

  • 引用安全模板wds-security

  • 名称：wds-leaf

  • WDS网桥名称：wlan-wds

  • WDS工作模式：leaf

  • Tagged VLAN：VLAN101

  • 引用安全模板wds-security

AP组

  • 名称：ap-group1

  • 用于添加root节点AP，如AP_1

  • 引用WDS模板wds-root、VAP模板wlan-net、域管理模板default

  • 名称：ap-group2

  • 用于添加root和leaf节点AP，如AP_2

  • 引用WDS模板wds-root和wds-leaf、VAP模板wlan-net、域管理模板default

  • 名称：ap-group3

  • 用于添加leaf节点AP，如AP_3

  • 引用WDS模板wds-leaf、VAP模板wlan-net、域管理模板default

配置思路
  1. 配置root节点AP_1在AC上线。
    1. 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。
    2. 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。
    3. 配置AP上线的认证方式并离线导入AP，实现AP正常上线。
  2. 配置WDS业务，使区域C的AP可以通过WDS无线虚链路上线。
  3. 配置WLAN业务参数，实现STA访问WLAN网络功能。
配置注意事项
  • 纯组播报文由于协议要求在无线空口没有ACK机制保障，且无线空口链路不稳定，为了纯组播报文能够稳定发送，通常会以低速报文形式发送。如果网络侧有大量异常组播流量涌入，则会造成无线空口拥堵。为了减小大量低速组播报文对无线网络造成的冲击，建议配置组播报文抑制功能。配置前请确认是否有组播业务，如果有，请谨慎配置限速值。
    • 业务数据转发方式采用直接转发时，建议在直连AP的交换机接口上配置组播报文抑制。
    • 业务数据转发方式采用隧道转发时，建议在AC的流量模板下配置组播报文抑制。

  • 建议在与AP直连的设备接口上配置端口隔离，如果不配置端口隔离，尤其是业务数据转发方式采用直接转发时，可能会在VLAN内形成大量不必要的广播报文，导致网络阻塞，影响用户体验。

  • 隧道转发模式下，管理VLAN和业务VLAN不能配置为同一VLAN，且AP和AC之间只能放通管理VLAN，不能放通业务VLAN。

  • 请按照WDS网络网规设计选用合适的天线，并选用天线校准工具进行校准。
操作步骤
  1. 配置周边设备

    # 配置接入交换机Switch_B的GE0/0/1和GE0/0/2接口加入VLAN100和VLAN101，GE0/0/1的缺省VLAN为VLAN100。

    1. <span style="color:#333333"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1141689396190921">system-view</strong>
    2. [HUAWEI] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1956857707190921">sysname Switch_B</strong>
    3. [Switch_B] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b402801205190921">vlan batch 100 to 101</strong>
    4. [Switch_B] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b611115067190921">interface gigabitEthernet 0/0/1</strong>
    5. [Switch_B-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b212116232190921">port link-type trunk</strong>
    6. [Switch_B-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1767714945190921">port trunk pvid vlan 100</strong>
    7. [Switch_B-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1214832445190921">port trunk allow-pass vlan 100 to 101</strong>
    8. [Switch_B-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b36947418190921">port-isolate enable</strong>
    9. [Switch_B-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1464937259190921">quit</strong>
    10. [Switch_B] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1250273224190921">interface gigabitEthernet 0/0/2</strong>
    11. [Switch_B-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b541902358190921">port link-type trunk</strong>
    12. [Switch_B-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1749851799190921">port trunk allow-pass vlan 100 to 101</strong>
    13. [Switch_B-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b809501523190921">quit</strong></span></span>

    # 配置汇聚交换机Switch_A的GE0/0/1接口加入VLAN100和VLAN101，GE0/0/2接口加入VLAN100，GE0/0/3接口加入VLAN101。

    1. <span style="color:#333333"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b511548958190921">system-view</strong>
    2. [HUAWEI] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b489891529190921">sysname Switch_A</strong>
    3. [Switch_A] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1311387655190921">vlan batch 100 to 101</strong>
    4. [Switch_A] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1243101138190921">interface gigabitEthernet 0/0/1</strong>
    5. [Switch_A-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1931666829190921">port link-type trunk</strong>
    6. [Switch_A-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1503245325190921">port trunk allow-pass vlan 100 to 101</strong>
    7. [Switch_A-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b289486029190921">quit</strong>
    8. [Switch_A] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b458500069190921">interface gigabitEthernet 0/0/2</strong>
    9. [Switch_A-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b779944513190921">port link-type trunk</strong>
    10. [Switch_A-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b85068874190921">port trunk allow-pass vlan 100</strong>
    11. [Switch_A-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b2034823831190921">quit</strong>
    12. [Switch_A] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b929617411190921">interface gigabitEthernet 0/0/3</strong>
    13. [Switch_A-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b766152642190921">port link-type trunk</strong>
    14. [Switch_A-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b1952032455190921">port trunk allow-pass vlan 101</strong>
    15. [Switch_A-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912382_b204948751190921">quit</strong></span></span>
    # 配置Router的接口GE1/0/0加入VLAN101，创建接口VLANIF101并配置IP地址为10.23.101.2/24。 
    1. <span style="color:#333333"><span style="background-color:#dddddd"><Huawei> <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b118005268190921">system-view</strong>
    2. [Huawei] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1176501588190921">sysname Router</strong>
    3. [Router] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b995805857190921">vlan batch 101</strong>
    4. [Router] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b906637926190921">interface gigabitethernet 1/0/0</strong>
    5. [Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b406876624190921">port link-type trunk</strong>
    6. [Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1226529678190921">port trunk allow-pass vlan 101</strong>
    7. [Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1131638750190921">quit</strong>
    8. [Router] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b648829236190921">interface vlanif 101</strong>
    9. [Router-Vlanif101] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1969966747190921">ip address 10.23.101.2 24</strong>
    10. [Router-Vlanif101] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1246477905190921">quit</strong></span></span>
  2. 配置AC与其它网络设备互通

    # 配置AC的接口GE0/0/1，允许携带VLAN100的报文通过。

    1. <span style="color:#333333"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0176912378__b570291284190921">system-view</strong>
    2. [HUAWEI] <strong id="ZH-CN_TASK_0176912378__b1926118503190921">sysname AC</strong>
    3. [AC] <strong id="ZH-CN_TASK_0176912378__b96916095190921">vlan batch 100 101</strong>
    4. [AC] <strong id="ZH-CN_TASK_0176912378__b404498836190921">interface gigabitEthernet 0/0/1</strong>
    5. [AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__b651322997190921">port link-type trunk</strong>
    6. [AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__b2619200190921">port trunk allow-pass vlan 100</strong>
    7. [AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0176912378__b987613193190921">quit</strong></span></span>
  3. 配置DHCP服务器为STA和AP分配IP地址

    DNS服务器地址请根据实际需要配置。常用配置方法如下：
    • 接口地址池场景，需要在VLANIF接口视图下执行命令dhcp server dns-list ip-address &<1-8>。
    • 全局地址池场景，需要在IP地址池视图下执行命令dns-list ip-address &<1-8>。
    # 配置Switch_A作为DHCP服务器，通过接口地址池为STA分配IP地址。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[Switch_A] <strong id="ZH-CN_TASK_0176912378__b585097426190921">dhcp enable</strong>
    2. [Switch_A] <strong id="ZH-CN_TASK_0176912378__b189439435190921">interface vlanif 101</strong>
    3. [Switch_A-Vlanif101] <strong id="ZH-CN_TASK_0176912378__b686378840190921">ip address 10.23.101.1 24</strong>
    4. [Switch_A-Vlanif101] <strong id="ZH-CN_TASK_0176912378__b1172640232190921">dhcp select interface</strong>
    5. [Switch_A-Vlanif101] <strong id="ZH-CN_TASK_0176912378__b685516536190921">dhcp server gateway-list 10.23.101.2</strong>
    6. [Switch_A-Vlanif101] <strong id="ZH-CN_TASK_0176912378__b116615007190921">quit</strong></span></span>

    # 在AC上使能DHCP功能，并通过接口地址池为AP分配IP地址。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0176912378__b535076932190921">dhcp enable</strong>
    2. [AC] <strong id="ZH-CN_TASK_0176912378__b1294910917190921">interface vlanif 100</strong>
    3. [AC-Vlanif100] <strong id="ZH-CN_TASK_0176912378__b1403704681190921">ip address 10.23.100.1 24</strong>
    4. [AC-Vlanif100] <strong id="ZH-CN_TASK_0176912378__b1618518344190921">dhcp select interface</strong>
    5. [AC-Vlanif100] <strong id="ZH-CN_TASK_0176912378__b1710882234190921">quit</strong></span></span>
  4. 配置AP上线

    # 创建AP组“ap-group1”、“ap-group2”和“ap-group3”。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0176912378__b1083860828190921">wlan</strong>
    2. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b333966974190921">ap-group name ap-group1</strong>
    3. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b2129810468190921">quit</strong>
    4. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1905879936190921">ap-group name ap-group2</strong>
    5. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b228340447190921">quit</strong>
    6. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b54960352190921">ap-group name ap-group3</strong>
    7. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b1032751598190921">quit</strong></span></span>

    # 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1230094218190921">regulatory-domain-profile name default</strong>
    2. [AC-wlan-regulate-domain-default] <strong id="ZH-CN_TASK_0176912378__b602460734190921">country-code cn</strong>
    3. [AC-wlan-regulate-domain-default] <strong id="ZH-CN_TASK_0176912378__b1938077640190921">quit</strong>
    4. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1312519707190921">ap-group name ap-group1</strong>
    5. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b204151839190921">regulatory-domain-profile default</strong>
    6. Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continue?[Y/N]:<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b17491131153716">y</strong>  
    7. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b594088353190921">quit</strong>
    8. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b817937082190921">ap-group name ap-group2</strong>
    9. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b815776022190921">regulatory-domain-profile default</strong>
    10. Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continue?[Y/N]:<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b17491131153716_1">y</strong>  
    11. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b1262782621190921">quit</strong>
    12. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b435925290190921">ap-group name ap-group3</strong>
    13. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b436826727190921">regulatory-domain-profile default</strong>
    14. Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continue?[Y/N]:<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b17491131153716_2">y</strong>  
    15. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b1227479814190921">quit</strong>
    16. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b741675262190921">quit</strong></span></span>

    # 配置AC的源接口。

    <span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0176912378__b1601735634190921">capwap source interface vlanif 100</strong></span></span>
    # 将AP_1加入到AP组“ap-group1”，AP_2加入到AP组“ap-group2”，AP_3加入到AP组“ap-group3”。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0176912378__b1374021969190921">wlan</strong>
    2. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1265509873190921">ap auth-mode mac-auth</strong>
    3. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b706866964190921">ap-id 1 ap-mac 60de-4474-9640</strong>
    4. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b176619692190921">ap-name AP_1</strong>
    5. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b600538503190921">ap-group ap-group1</strong>
    6. Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1651706244190906">y</strong>  
    7. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b435831157190921">quit</strong>
    8. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1734348834190921">ap-id 2 ap-mac dcd2-fc04-b500</strong>
    9. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1101981659190921">ap-name AP_2</strong>
    10. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1077418825190921">ap-group ap-group2</strong>
    11. Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1651706244190906_1">y</strong>  
    12. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1999555100190921">quit</strong>
    13. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1250311975190921">ap-id 3 ap-mac dcd2-fc96-e4c0</strong>
    14. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b1533697021190921">ap-name AP_3</strong>
    15. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b1508108276190921">ap-group ap-group3</strong>
    16. Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1651706244190906_2">y</strong>  
    17. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b1982018367190921">quit</strong></span></span>
  5. 配置WDS业务参数

    # 配置WDS节点使用的主要射频参数。本例中使用AP_1和AP_3的是AP8130DN的射频1，AP_2使用AP8130DN的射频0和射频1。配置AP_2的射频0工作在5GHz频段，为了减少信道干扰配置AP_2的射频0和射频1在不同的信道，射频1用于和AP_1建立WDS链路，射频0用于和AP_3建立WDS链路。“coverage distance”参数为射频覆盖距离，缺省情况下是3，单位是100m。本例中使用参数为4，用户可以根据实际情况配置该参数。

    在WDS网络中，建立WDS链路的射频必须为同一信道。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b973163930190921">ap-id 2</strong>
    2. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1881699822190921">radio 0</strong>
    3. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b594094206190921">frequency 5g</strong>
    4. Warning: Modifying the frequency band will delete the channel, power, and antenn
    5. a gain configurations of the current radio on the AP and reboot the AP. Continue
    6. ?[Y/N]:<strong id="ZH-CN_TASK_0176912378__b1855572944920">y</strong>
    7. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b1918124164190921">quit</strong>
    8. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b2038603550190921">quit</strong>
    9. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1099814393190921">ap-id 1</strong>
    10. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b1669668313190921">radio 1</strong>
    11. [AC-wlan-radio-1/1] <strong id="ZH-CN_TASK_0176912378__b1295367688190921">channel 40mhz-plus 157</strong>
    12. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1384307436190906">y</strong> 
    13. [AC-wlan-radio-1/1] <strong id="ZH-CN_TASK_0176912378__b1221378632190921">coverage distance 4</strong>
    14. [AC-wlan-radio-1/1] <strong id="ZH-CN_TASK_0176912378__b1620252618190921">quit</strong>
    15. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b990496967190921">quit</strong>
    16. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1896739578190921">ap-id 2</strong>
    17. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b2050334401190921">radio 0</strong>
    18. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b1449906778190921">channel 40mhz-plus 149</strong>
    19. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1384307436190906_1">y</strong> 
    20. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b1331953824190921">coverage distance 4</strong>
    21. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b713880646190921">quit</strong>
    22. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1137368453190921">radio 1</strong>
    23. [AC-wlan-radio-2/1] <strong id="ZH-CN_TASK_0176912378__b823627637190921">channel 40mhz-plus 157</strong>
    24. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1384307436190906_2">y</strong> 
    25. [AC-wlan-radio-2/1] <strong id="ZH-CN_TASK_0176912378__b1762660870190921">coverage distance 4</strong>
    26. [AC-wlan-radio-2/1] <strong id="ZH-CN_TASK_0176912378__b1281892212190921">quit</strong>
    27. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1863079157190921">quit</strong>
    28. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1502886139190921">ap-id 3</strong>
    29. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b604612192190921">radio 1</strong>
    30. [AC-wlan-radio-3/1] <strong id="ZH-CN_TASK_0176912378__b298941086190921">channel 40mhz-plus 149</strong>
    31. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__zh-cn_task_0175818418_b1384307436190906_3">y</strong> 
    32. [AC-wlan-radio-3/1] <strong id="ZH-CN_TASK_0176912378__b1153657628190921">coverage distance 4</strong>
    33. [AC-wlan-radio-3/1] <strong id="ZH-CN_TASK_0176912378__b1519769423190921">quit</strong>
    34. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b1134031871190921">quit</strong></span></span>

    # 配置WDS链路使用的安全模板“wds-security”，“wds-security”的安全策略为WPA2+PSK+AES。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b403659190190921">security-profile name wds-security</strong>
    2. [AC-wlan-sec-prof-wds-security] <strong id="ZH-CN_TASK_0176912378__b680615166190921">security wpa2 psk pass-phrase a1234567 aes</strong>
    3. [AC-wlan-sec-prof-wds-security] <strong id="ZH-CN_TASK_0176912378__b1709946791190921">quit</strong></span></span>

    # 配置WDS白名单。配置AP_1绑定的WDS白名单“wds-list1”，仅允许AP_2接入。配置AP_2绑定的WDS白名单“wds-list2”，仅允许AP_3接入。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b36601203190921">wds-whitelist-profile name wds-list1</strong>
    2. [AC-wlan-wds-whitelist-wds-list1] <strong id="ZH-CN_TASK_0176912378__b1735750903190921">peer-ap mac dcd2-fc04-b500</strong>
    3. [AC-wlan-wds-whitelist-wds-list1] <strong id="ZH-CN_TASK_0176912378__b916949979190921">quit</strong>
    4. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b685098719190921">wds-whitelist-profile name wds-list2</strong>
    5. [AC-wlan-wds-whitelist-wds-list2] <strong id="ZH-CN_TASK_0176912378__b1881723973190921">peer-ap mac dcd2-fc96-e4c0</strong>
    6. [AC-wlan-wds-whitelist-wds-list2] <strong id="ZH-CN_TASK_0176912378__b1433362236190921">quit</strong></span></span>

    # 配置WDS模板“wds-root”。网桥标识为“wlan-wds”，网桥模式为“root”，引用安全模板“wds-security”，以tagged形式允许无线业务VLAN101通过。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1038160682190921">wds-profile name wds-root</strong>
    2. [AC-wlan-wds-prof-wds-root] <strong id="ZH-CN_TASK_0176912378__b1316032594190921">wds-name wlan-wds</strong>
    3. [AC-wlan-wds-prof-wds-root] <strong id="ZH-CN_TASK_0176912378__b447826258190921">wds-mode root</strong>
    4. [AC-wlan-wds-prof-wds-root] <strong id="ZH-CN_TASK_0176912378__b2069070593190921">security-profile wds-security</strong>
    5. [AC-wlan-wds-prof-wds-root] <strong id="ZH-CN_TASK_0176912378__b146100745190921">vlan tagged 101</strong>
    6. [AC-wlan-wds-prof-wds-root] <strong id="ZH-CN_TASK_0176912378__b1070862885190921">quit</strong></span></span>

    # 配置WDS模板“wds-leaf”。网桥标识为“wlan-wds”，网桥模式为“leaf”，引用安全模板“wds-security”，以tagged形式允许无线业务VLAN101通过。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1978990317190921">wds-profile name wds-leaf</strong>
    2. [AC-wlan-wds-prof-wds-leaf] <strong id="ZH-CN_TASK_0176912378__b209671589190921">wds-name wlan-wds</strong>
    3. [AC-wlan-wds-prof-wds-leaf] <strong id="ZH-CN_TASK_0176912378__b1205789701190921">wds-mode leaf</strong>
    4. [AC-wlan-wds-prof-wds-leaf] <strong id="ZH-CN_TASK_0176912378__b1124331768190921">security-profile wds-security</strong>
    5. [AC-wlan-wds-prof-wds-leaf] <strong id="ZH-CN_TASK_0176912378__b1747517715190921">vlan tagged 101</strong>
    6. [AC-wlan-wds-prof-wds-leaf] <strong id="ZH-CN_TASK_0176912378__b180610353190921">quit</strong></span></span>

    # 配置AP组“ap-group1”的射频1引用WDS白名单“wds-list1”。配置AP组“ap-group2”的射频0引用WDS白名单“wds-list2”。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b61345628190921">ap-group name ap-group1</strong>
    2. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b21897143190921">radio 1</strong>
    3. [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0176912378__b1700089180190921">wds-whitelist-profile wds-list1</strong>
    4. [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0176912378__b1318962636190921">quit</strong>
    5. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b7517099190921">quit</strong>
    6. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b25484107190921">ap-group name ap-group2</strong>
    7. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b1891047689190921">radio 0</strong>
    8. [AC-wlan-group-radio-ap-group2/0] <strong id="ZH-CN_TASK_0176912378__b715150691190921">wds-whitelist-profile wds-list2</strong>
    9. [AC-wlan-group-radio-ap-group2/0] <strong id="ZH-CN_TASK_0176912378__b2099109151190921">quit</strong>
    10. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b781464261190921">quit</strong></span></span>
  6. 在AP组引用相关模板，使WDS业务生效

    # 配置AP组“ap-group1”，引用WDS模板“wds-root”。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1602084839190921">ap-group name ap-group1</strong>
    2. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b2053795237190921">wds-profile wds-root radio 1</strong>
    3. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__b1345959752190921">y</strong>
    4. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b153560152190921">quit</strong></span></span>

    # 配置AP组“ap-group2”，引用WDS模板“wds-root”和“wds-leaf”。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b435889682190921">ap-group name ap-group2</strong>
    2. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b1308033525190921">wds-profile wds-leaf radio 1</strong>
    3. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__b1195614921190921">y</strong>
    4. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b1295779174190921">wds-profile wds-root radio 0</strong>
    5. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__b1778551390190921">y</strong>
    6. [AC-wlan-ap-group-ap-group2] <strong id="ZH-CN_TASK_0176912378__b174749758190921">quit</strong></span></span>

    # 配置AP组“ap-group3”，引用WDS模板“wds-leaf”。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b299621465190921">ap-group name ap-group3</strong>
    2. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b1283922214190921">wds-profile wds-leaf radio 1</strong>
    3. Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0176912378__b10513943190921">y</strong>
    4. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b618593862190921">quit</strong></span></span>
  7. 配置WLAN业务参数

    # 创建名为“wlan-net”的安全模板，并配置安全策略。

    举例中以配置WPA-WPA2+PSK+AES的安全策略为例，密码为“a1234567”，实际配置中请根据实际情况，配置符合实际要求的安全策略。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1991067776190921">security-profile name wlan-net</strong>
    2. [AC-wlan-sec-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b851752672190921">security wpa-wpa2 psk pass-phrase a1234567 aes</strong>
    3. [AC-wlan-sec-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b337241812190921">quit</strong></span></span>
    # 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b69022931190921">ssid-profile name wlan-net</strong>
    2. [AC-wlan-ssid-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b36723145190921">ssid wlan-net</strong>
    3. [AC-wlan-ssid-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__zh-cn_task_0176912351_b1738903244190921">quit</strong></span></span>
    # 创建名为“wlan-net”的VAP模板，配置业务数据转发模式、业务VLAN，并且引用安全模板和SSID模板。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b325802584190921">vap-profile name wlan-net</strong>
    2. [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__b977737230190921">forward-mode direct-forward</strong>
    3. [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__b1495141052190921">service-vlan vlan-id 101</strong>
    4. [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__b694670004190921">security-profile wlan-net</strong>
    5. [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__b411554548190921">ssid-profile wlan-net</strong>
    6. [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0176912378__b1808978522190921">quit</strong></span></span>
    # 配置AP组引用VAP模板，本例中AP_1和AP_3使用射频1作为WDS回传频段，射频0作为无线业务覆盖射频。AP_1和AP_3上射频0都使用VAP模板“wlan-net”的配置。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b908252767190921">ap-group name ap-group1</strong>
    2. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b1382046263190921">vap-profile wlan-net wlan 1 radio 0</strong>
    3. [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0176912378__b1809376582190921">quit</strong>
    4. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b65311999190921">ap-group name ap-group3</strong>
    5. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b102213109190921">vap-profile wlan-net wlan 3 radio 0</strong>
    6. [AC-wlan-ap-group-ap-group3] <strong id="ZH-CN_TASK_0176912378__b340378414190921">quit</strong></span></span>
  8. 配置AP 2.4G射频的信道和功率

    举例中AP射频的信道和功率仅为示例，实际配置中请根据AP的国家码和网规结果进行配置。

    # 关闭AP射频的信道和功率自动调优功能。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1952682364190921">ap-id 1</strong>
    2. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b1706775230190921">radio 0</strong>
    3. [AC-wlan-radio-1/0] <strong id="ZH-CN_TASK_0176912378__b1242645581190921">calibrate auto-channel-select disable</strong>
    4. [AC-wlan-radio-1/0] <strong id="ZH-CN_TASK_0176912378__b1300815155190921">calibrate auto-txpower-select disable</strong>
    5. [AC-wlan-radio-1/0] <strong id="ZH-CN_TASK_0176912378__b665627777190921">quit</strong>
    6. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b1937134891190921">radio 1</strong>
    7. [AC-wlan-radio-1/1] <strong id="ZH-CN_TASK_0176912378__b964854892190921">calibrate auto-channel-select disable</strong>
    8. [AC-wlan-radio-1/1] <strong id="ZH-CN_TASK_0176912378__b1162033439190921">calibrate auto-txpower-select disable</strong>
    9. [AC-wlan-radio-1/1] <strong id="ZH-CN_TASK_0176912378__b165350850190921">quit</strong>
    10. [AC-wlan-ap-1]<strong id="ZH-CN_TASK_0176912378__b621637696190921">quit</strong>
    11. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1234068911190921">ap-id 2</strong>
    12. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b229842564190921">radio 0</strong>
    13. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b1342934364190921">calibrate auto-channel-select disable</strong>
    14. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b1711548828190921">calibrate auto-txpower-select disable</strong>
    15. [AC-wlan-radio-2/0] <strong id="ZH-CN_TASK_0176912378__b1360369703190921">quit</strong>
    16. [AC-wlan-ap-2] <strong id="ZH-CN_TASK_0176912378__b1588443530190921">radio 1</strong>
    17. [AC-wlan-radio-2/1] <strong id="ZH-CN_TASK_0176912378__b588981595190921">calibrate auto-channel-select disable</strong>
    18. [AC-wlan-radio-2/1] <strong id="ZH-CN_TASK_0176912378__b1840220766190921">calibrate auto-txpower-select disable</strong>
    19. [AC-wlan-radio-2/1] <strong id="ZH-CN_TASK_0176912378__b1725333130190921">quit</strong>
    20. [AC-wlan-ap-2]<strong id="ZH-CN_TASK_0176912378__b1261464425190921">quit</strong>
    21. [AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b622120274190921">ap-id 3</strong>
    22. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b171438672190921">radio 0</strong>
    23. [AC-wlan-radio-3/0] <strong id="ZH-CN_TASK_0176912378__b2132985172190921">calibrate auto-channel-select disable</strong>
    24. [AC-wlan-radio-3/0] <strong id="ZH-CN_TASK_0176912378__b271202200190921">calibrate auto-txpower-select disable</strong>
    25. [AC-wlan-radio-3/0] <strong id="ZH-CN_TASK_0176912378__b1526864825190921">quit</strong>
    26. [AC-wlan-ap-3] <strong id="ZH-CN_TASK_0176912378__b91027589190921">radio 1</strong>
    27. [AC-wlan-radio-3/1] <strong id="ZH-CN_TASK_0176912378__b1535412287190921">calibrate auto-channel-select disable</strong>
    28. [AC-wlan-radio-3/1] <strong id="ZH-CN_TASK_0176912378__b1762757286190921">calibrate auto-txpower-select disable</strong>
    29. [AC-wlan-radio-3/1] <strong id="ZH-CN_TASK_0176912378__b85195689190921">quit</strong>
    30. [AC-wlan-ap-3]<strong id="ZH-CN_TASK_0176912378__b78324845190921">quit</strong></span></span>
    # 配置AP射频0的信道和功率。 
    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b586443666190921">ap-id 1</strong>
    2. [AC-wlan-ap-1] <strong id="ZH-CN_TASK_0176912378__b423411733190921">radio 0</strong>
    3. [AC-wlan-radio-1/0] <strong id="ZH-CN_TASK_0176912378__b2007086283190921">channel 20mhz 6</strong>
    4. Warning: This action may cause service interruption. Continue?[Y/N]y
    5. [AC-wlan-radio-1/0] <strong id="ZH-CN_TASK_0176912378__b1030138178190921">eirp 127</strong>
    6. [AC-wlan-radio-1/0] <strong id="ZH-CN_TASK_0176912378__b1917905811190921">quit</strong>
    7. [AC-wlan-ap-1]<strong id="ZH-CN_TASK_0176912378__b559165017190921">quit</strong></span></span>
  9. 验证WDS业务配置结果

    完成配置后，执行命令display ap all，查看WDS各节点是否成功上线，当“State”字段显示为“nor”，则表示AP已成功上线。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1107332355190921">display ap all</strong>
    2. Total AP information:
    3. nor  : normal          [3]
    4. Extra information: P  : insufficient power supply
    5. --------------------------------------------------------------------------------------------------
    6. ID   MAC            Name   Group     IP            Type            State STA Uptime      ExtraInfo
    7. --------------------------------------------------------------------------------------------------
    8. 1    60de-4474-9640 AP_1   ap-group1 10.23.100.254 AP8130DN        <strong id="ZH-CN_TASK_0176912378__b58094169190921">nor</strong>   0   20M:16S     -
    9. 2    dcd2-fc04-b500 AP_2   ap-group2 10.23.100.253 AP8130DN        <strong id="ZH-CN_TASK_0176912378__b2093037571190921">nor</strong>   0   17S         -
    10. 3    dcd2-fc96-e4c0 AP_3   ap-group3 10.23.100.252 AP8130DN        <strong id="ZH-CN_TASK_0176912378__b1074348771190921">nor</strong>   0   3M:55S      -
    11. --------------------------------------------------------------------------------------------------
    12. Total: 3
    13. </span></span>

    执行命令display wlan wds link all，查看WDS链路相关信息。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b1520620916190921">display wlan wds link all</strong>
    2. Rf   : radio ID             Dis  : coverage distance(100m)                      
    3. Ch   : channel              Per  : drop percent(%)                              
    4. TSNR : total SNR(dB)        P-   : peer                                         
    5. WDS  : WDS mode             Re   : retry ratio(%)                               
    6. RSSI : RSSI(dBm)            MaxR : max RSSI(dBm)                                
    7. -------------------------------------------------------------------------------------------------
    8. APName  P-APName  Rf Dis   Ch   WDS     P-Status        RSSI  MaxR  Per  Re   TS  NR  SNR(Ch0~3:dB)
    9. -------------------------------------------------------------------------------------------------
    10. AP_1    AP_2      1  4     157  root     normal          -39   -30   0    5   55    42/57/-/-
    11. AP_2    AP_3      0  4     149  root     normal          -56   -40   0    9   59    45/40/60/-
    12. AP_2    AP_1      1  4     157  leaf     normal          -32   -30   0    15  58    41/36/60/-
    13. AP_3    AP_2      1  4     149  leaf     normal          -33   -32   0    7   59    51/59/-/-
    14. ---------------------------------------------------------------------------------------------------
    15. Total: 4</span></span>

    WLAN业务配置会自动下发给AP，配置完成后，通过执行命令display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP对应的射频上的VAP已创建成功。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b287801376190921">display vap ssid wlan-net</strong>
    2. WID : WLAN ID
    3. --------------------------------------------------------------------------------
    4. AP ID AP name RfID WID   BSSID          Status  Auth type     STA   SSID
    5. --------------------------------------------------------------------------------
    6. 1     AP_1    0    1     60DE-4474-9640 <strong id="ZH-CN_TASK_0176912378__b32085512190921">ON</strong>      WPA/WPA2-PSK  0     wlan-net
    7. 3     AP_3    0    3     DCD2-FC96-E4C0 <strong id="ZH-CN_TASK_0176912378__b1358396375190921">ON</strong>      WPA/WPA2-PSK  0     wlan-net
    8. -------------------------------------------------------------------------------
    9. Total: 2</span></span>

    STA搜索到名为“wlan-net”的无线网络，输入密码“a1234567”并正常关联后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线网络“wlan-net”中。

    1. <span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0176912378__b277077308190921">display station ssid wlan-net</strong>
    2. Rf/WLAN: Radio ID/WLAN ID
    3. Rx/Tx: link receive rate/link transmit rate(Mbps)
    4. ---------------------------------------------------------------------------------
    5. STA MAC         AP ID Ap name   Rf/WLAN  Band  Type  Rx/Tx      RSSI  VLAN  IP address
    6. ---------------------------------------------------------------------------------
    7. e019-1dc7-1e08  1     AP_1      0/1      2.4G  11n   3/34       -68   101   10.23.101.254
    8. ---------------------------------------------------------------------------------
    9. Total: 1 2.4G: 1 5G: 0</span></span>
配置文件

  • Switch_A的配置文件

    1. <span style="color:#333333"><span style="background-color:#dddddd">#
    2. sysname Switch_A
    3. #
    4.  vlan batch 100 to 101
    5. #
    6. dhcp enable 
    7. #
    8. interface Vlanif101
    9.  ip address 10.23.101.1 255.255.255.0
    10.  dhcp select interface
    11. #
    12. interface GigabitEthernet0/0/1
    13.  port link-type trunk
    14.  port trunk allow-pass vlan 100 to 101
    15. #
    16. interface GigabitEthernet0/0/2
    17.  port link-type trunk
    18.  port trunk allow-pass vlan 100
    19. #
    20. interface GigabitEthernet0/0/3
    21.  port link-type trunk
    22.  port trunk allow-pass vlan 101
    23. #
    24. return</span></span>

  • Switch_B的配置文件

    1. <span style="color:#333333"><span style="background-color:#dddddd">#
    2. sysname Switch_B
    3. #
    4.  vlan batch 100 to 101
    5. #
    6. interface GigabitEthernet0/0/1
    7.  port link-type trunk
    8.  port trunk pvid vlan 100
    9.  port trunk allow-pass vlan 100 to 101
    10.  port-isolate enable group 1 
    11. #
    12. interface GigabitEthernet0/0/2
    13.  port link-type trunk
    14.  port trunk allow-pass vlan 100 to 101
    15. #
    16. return</span></span>

  • Router的配置文件

    1. <span style="color:#333333"><span style="background-color:#dddddd">#
    2. sysname Router
    3. #
    4. vlan batch 101
    5. #
    6. interface Vlanif101
    7.  ip address 10.23.101.2 255.255.255.0
    8. #
    9. interface GigabitEthernet1/0/0
    10.  port link-type trunk
    11.  port trunk allow-pass vlan 101
    12. #
    13. return
    14. </span></span>

  • AC的配置文件

    1. <span style="color:#333333"><span style="background-color:#dddddd">#
    2.  sysname AC
    3. #
    4.  vlan batch 100 to 101
    5. #
    6. dhcp enable 
    7. #
    8. interface Vlanif100
    9.  ip address 10.23.100.1 255.255.255.0
    10.  dhcp select interface
    11. #
    12. interface GigabitEthernet0/0/1
    13.  port link-type trunk
    14.  port trunk allow-pass vlan 100
    15. #
    16. capwap source interface vlanif100
    17. #
    18. wlan
    19.  security-profile name wlan-net
    20.   security wpa-wpa2 psk pass-phrase %^%#m"tz0f>~7.[`^6RWdzwCy16hJj/Mc!,}s`X*B]}A%^%# aes
    21.  security-profile name wds-security
    22.   security wpa2 psk pass-phrase %^%#n}5+DgC3wLB.hJ34j5;*QMv<8"9#{Bq@ghBI3L9K%^%# aes
    23.  ssid-profile name wlan-net
    24.   ssid wlan-net
    25.  vap-profile name wlan-net
    26.   service-vlan vlan-id 101
    27.   ssid-profile wlan-net
    28.   security-profile wlan-net
    29.  wds-whitelist-profile name wds-list1
    30.   peer-ap mac dcd2-fc04-b500
    31.  wds-whitelist-profile name wds-list2
    32.   peer-ap mac dcd2-fc96-e4c0
    33.  wds-profile name wds-leaf
    34.   security-profile wds-security
    35.   vlan tagged 101
    36.   wds-name wlan-wds
    37.  wds-profile name wds-root
    38.   security-profile wds-security
    39.   vlan tagged 101
    40.   wds-name wlan-wds
    41.   wds-mode root
    42.  regulatory-domain-profile name default
    43.  ap-group name ap-group1
    44.   radio 0
    45.    vap-profile wlan-net wlan 3
    46.   radio 1
    47.    wds-profile wds-root
    48.    wds-whitelist-profile wds-list1
    49.  ap-group name ap-group2
    50.   radio 0
    51.    wds-profile wds-root
    52.    wds-whitelist-profile wds-list2
    53.   radio 1
    54.    wds-profile wds-leaf
    55.  ap-group name ap-group3
    56.   radio 0
    57.    vap-profile wlan-net wlan 1
    58.   radio 1
    59.    wds-profile wds-leaf
    60.  ap-id 1 type-id 39 ap-mac 60de-4474-9640 ap-sn 210235554710CB000042
    61.   ap-name AP_1
    62.   ap-group ap-group1
    63.   radio 0
    64.    channel 20mhz 6
    65.    eirp 127
    66.    calibrate auto-channel-select disable    calibrate auto-txpower-select disable
    67.   radio 1
    68.    channel 40mhz-plus 157
    69.    coverage distance 4
    70.    calibrate auto-channel-select disable    calibrate auto-txpower-select disable
    71.  ap-id 2 type-id 39 ap-mac dcd2-fc04-b500 ap-sn 210235555310CC000094
    72.   ap-name AP_2
    73.   ap-group ap-group2
    74.   radio 0
    75.    frequency 5g
    76.    channel 40mhz-plus 149
    77.    eirp 127
    78.    coverage distance 4 
    79.    calibrate auto-channel-select disable    calibrate auto-txpower-select disable
    80.   radio 1
    81.    channel 40mhz-plus 157
    82.    eirp 127
    83.    coverage distance 4 
    84.    calibrate auto-channel-select disable    calibrate auto-txpower-select disable
    85.  ap-id 3 type-id 39 ap-mac dcd2-fc96-e4c0 ap-sn 210235557610DB000046
    86.   ap-name AP_3
    87.   ap-group ap-group3
    88.   radio 0
    89.    channel 20mhz 11
    90.    eirp 127
    91.    calibrate auto-channel-select disable    calibrate auto-txpower-select disable
    92.   radio 1
    93.    channel 40mhz-plus 149
    94.    coverage distance 4 
    95.    calibrate auto-channel-select disable    calibrate auto-txpower-select disable
    96. #  
    97. return</span></span>
声明：本文内容由网友自发贡献，不代表【wpsshop博客】立场，版权归原作者所有，本站不承担相应法律责任。如您发现有侵权的内容，请联系我们。转载请注明出处：https://www.wpsshop.cn/w/Gausst松鼠会/article/detail/167670
推荐阅读
相关标签

Copyright © 2003-2013 www.wpsshop.cn 版权所有，并保留所有权利。

  

闽ICP备14008679号