Quectel EC200A-CN移植

一:usb转串口

usb-serial-option,USB转串口驱动，生产/dev/ttyUSB0-2,分别是DM，AT，PPP
需要使能内核选项如下:

CONFIG_USB_SERIAL=y
CONFIG_USB_SERIAL_WWAN=y
CONFIG_USB_SERIAL_OPTION=y
1
2
3

二:usb网卡驱动

USB网卡驱动，模块可通过AT配置成RNDIS或者ecm,默认是ecm。
需要使能内核选项

USB_USBNET=y
USB_NET_CDCETHER=y        #用ECM  使能此项
USB_NET_RNDIS_HOST=y      #用RNDIS 使能此项
1
2
3

三:源码修改

1. 增加usb vid和pid
   增加vid和pid,设备连接，使用lsusb命令查看设备的vid和pid，如下图所示：
   

vid:3763
pid:3c93
1
2

文件修改:linux-3.10/drivers/usb/serial/option.c

static const struct usb_device_id option_ids[] = {
#if 1 //Added by Quectel
        { USB_DEVICE(0x3763, 0x3c93) }, /* Quectel EC200A-CN 内置GPS */
        { USB_DEVICE(0x3c93, 0xffff) }, /* Quectel EC200A-CN 外置GPS*/
#endif
1
2
3
4
5

文件修改:linux-3.10/drivers/usb/serial/option.c

1790 #if 1 //Added by Quectel
1791 static void cfmakeraw(struct ktermios *t)
1792 {
1793         t->c_iflag &= ~(IGNBRK|BRKINT|PARMRK|ISTRIP|INLCR|IGNCR|ICRNL|IXON);
1794         t->c_oflag &= ~OPOST;
1795         t->c_lflag &= ~(ECHO|ECHONL|ICANON|ISIG|IEXTEN);
1796         t->c_cflag &= ~(CSIZE|PARENB);
1797         t->c_cflag |= CS8;
1798         t->c_cc[VMIN] = 1;
1799         t->c_cc[VTIME] = 0;
1800 }
1801 
1802 static void option_init_termios(struct tty_struct *tty)
1803 {
1804         cfmakeraw(&tty->termios);
1805 }
1806 #endif
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

文件修改:linux-3.10/drivers/usb/serial/option.c:option_1port_device

1813 static struct usb_serial_driver option_1port_device = {
1814         .driver = {
1815                 .owner =        THIS_MODULE,
1816                 .name =         "option1",
1817         },
1818         .description       = "GSM modem (1-port)",
1819         .id_table          = option_ids,
1820         .num_ports         = 1,
1821         .probe             = option_probe,
1822         .open              = usb_wwan_open,
1823         .close             = usb_wwan_close,
1824         .dtr_rts           = usb_wwan_dtr_rts,
1825         .write             = usb_wwan_write,
1826         .write_room        = usb_wwan_write_room,
1827         .chars_in_buffer   = usb_wwan_chars_in_buffer,
1828         .set_termios       = usb_wwan_set_termios,
1829         .tiocmget          = usb_wwan_tiocmget,
1830         .tiocmset          = usb_wwan_tiocmset,
1831         .ioctl             = usb_wwan_ioctl,
1832         .attach            = option_attach,
1833         .release           = option_release,
1834         .port_probe        = usb_wwan_port_probe,
1835         .port_remove       = usb_wwan_port_remove,
1836         .read_int_callback = option_instat_callback,
1837 #ifdef CONFIG_PM
1838         .suspend           = usb_wwan_suspend,
1839         .resume            = usb_wwan_resume,
1840 #if 1 //Added by Quectel
1841         .reset_resume = usb_wwan_resume,
1842 #endif
1843 #endif
1844 };
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

文件修改:linux-3.10/drivers/usb/serial/option.c:option_probe

if (serial->dev->descriptor.idVendor == cpu_to_le16(0x3c93))
{
        __u16 idProduct = le16_to_cpu(serial->dev->descriptor.idProduct);
        struct usb_interface_descriptor *intf = &serial->interface->cur_altsetting->desc;

        if (intf->bInterfaceClass != 0xFF || intf->bInterfaceSubClass == 0x42)
        {
                //ECM, RNDIS, NCM, MBIM, ACM, UAC, ADB
                return -ENODEV;
        }

        if ((idProduct&0xF000) == 0x0000)
        {
                //MDM interface 4 is QMI
                if (intf->bInterfaceNumber == 4 &&
                    intf->bNumEndpoints == 3 &&
                    intf->bInterfaceSubClass == 0xFF &&
                    intf->bInterfaceProtocol == 0xFF)
                        return -ENODEV;
        }
}
if (serial->dev->descriptor.idVendor == cpu_to_le16(0x3763))
{
        __u16 idProduct = le16_to_cpu(serial->dev->descriptor.idProduct);
        struct usb_interface_descriptor *intf = &serial->interface->cur_altsetting->desc;

        if (intf->bInterfaceClass != 0xFF || intf->bInterfaceSubClass == 0x42)
        {
                //ECM, RNDIS, NCM, MBIM, ACM, UAC, ADB
                return -ENODEV;
        }

        if ((idProduct&0xF000) == 0x0000)
        {
                //MDM interface 4 is QMI
                if (intf->bInterfaceNumber == 4 &&
                    intf->bNumEndpoints == 3 &&
                    intf->bInterfaceSubClass == 0xFF &&
                    intf->bInterfaceProtocol == 0xFF)
                        return -ENODEV;
        }
}
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

2. linux-3.10/drivers/usb/serial/usb_wwan.c:usb_wwan_setup_urb
   在usb_wwan_setup_urb函数中添加如下内容

 //Added by Quectel for Zero Packet
 if (dir == USB_DIR_OUT) {
         struct usb_device_descriptor *desc = &serial->dev->descriptor;
 if (desc->idVendor == cpu_to_le16(0x05C6) && desc->idProduct == cpu_to_le16(0x9090))
         urb->transfer_flags |= URB_ZERO_PACKET;
 if (desc->idVendor == cpu_to_le16(0x05C6) && desc->idProduct == cpu_to_le16(0x9003))
         urb->transfer_flags |= URB_ZERO_PACKET;
 if (desc->idVendor == cpu_to_le16(0x05C6) && desc->idProduct == cpu_to_le16(0x9215))
         urb->transfer_flags |= URB_ZERO_PACKET;
 if (desc->idVendor == cpu_to_le16(0x2C7C))
         urb->transfer_flags |= URB_ZERO_PACKET;
 if (desc->idVendor == cpu_to_le16(0x3c93))
         urb->transfer_flags |= URB_ZERO_PACKET;
 if (desc->idVendor == cpu_to_le16(0x3763))
         urb->transfer_flags |= URB_ZERO_PACKET;
 }
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

四:测试

1. 查看usb网卡是否生成

ifconfig -a
1

2. 测试方法一

busybox microcom /dev/ttyUSB2
1

3. 测试方法二

cat /dev/ttyUSB2 &
echo AT > /dev/ttyUSB2
1
2