赞
踩
折腾了好久,终于能通过arduino把程序烧录至esp8266了,看了好多教程资料,大多不全,模棱两可,不适合初学者。后续更新:https://daoker.cc/daokerto18.html
一、引脚定义
参考文献:
ESP8266(一)—引脚定义&接线说明
他的接线部分和我的不同。我的rx-rx,tx-tx,具体有没有接对可以用程序进行测试。
二.接线说明
参考文献:Arduino uno r3 使用 ESP8266 wifi 模块完整流程
这里我chpd(en)直接接3.3v也没事
把代码上传到arduino,测试接线正确与否。
const int tx = 1;
const int rx = 0;
void setup() {
//Serial.begin(9600); 注意!!千万别加这行代码
pinMode(rx,INPUT_PULLUP);
pinMode(tx,INPUT_PULLUP);
}
void loop() {
}
每个版本的ESP8266波特率不同,一般是115200,你可以多测试几次。
SP8266 的 AT 命令可以在网上查,比如下面的这几个
AT+RST 重启模块
AT+GMR 查看版本信息
AT+CIOBAUD=9600 修改波特率
T+CWMODE? //查询工作模式 1.Station (客户端模式)2.AP (接入点模式)3.Station+AP (两种模式共存)
三.程序烧录至ESP8266
我看网上有的教程说要取掉arduino的啥啥啥芯片,我这个貌似不可拆,还有的是用专门的下载线和烧录软件,这个我也没有。
直到找到了这篇文章
Arduino和ESP8266-模块安装及代码上传
简单介绍,就是:
1.添加开发板管理网站http://arduino.esp8266.com/stable/package_esp8266com_index.json
2.在开发板管理器里安装ESP8266 Community。此步骤可能需要fq,如果没有可以下载离线包,也可以用这个帖子里分享的Arduino IDE安装esp8266 SDK(Windows10),或者自己去github下载
3.选择开发板,可以按照参考文献里的来配置
Arduino和ESP8266-模块安装及代码上传
Arduino烧录ESP8266模块,实现WiFi通信,连接OneNET平台(一)
我是选了Generic ESP8266 Module,其他都是默认没动,这里我最高版本的ARDUINO IDE里编程器下面没有选项,查了很多资料也没有这个问题的解释,所以我换了低一点版本的IDE就有了,我选skII。
4.烧录,在IDE里写好代码后,
将ESP8266设定为FLASH(烧写)模式:当GPIO0(上图紫色线)接地线时,ESP8266是以bootloader模式(编程模式)启动的,这也就是你可以烧写ESP8266(将Arduino上的代码转移到ESP8266上)的时候。在Arduino代码加载完毕时,你将看到Arduino IDE底部提示“上传结束”的信息,然后代码就会开始运行了。
程序上传结束后,将紫色线移除:当你不想将ESP8266一直设定为烧写模式时,将紫色线移除即可,程序将会一直在ESP8266上执行。
来源Arduino结合ESP8266 Serial WIFI模块访问远程服务器
实际操作:
【3】确保如上面连线图所示,A、B两条连线断开,即esp8266的EN、IO0针脚和UNO板子之间是断开的,
【4】点击IDE的 [上传] 按钮,开始通过UNO板子向esp8266烧写程序,
【5】当日志窗口出现 “Connecting…………………_____” 字样时,
【6.1】首先,将ESP8266的IO0和UNO板子的GND连接,
【6.2】接着,将ESP8266的EN和UNO的3.3V连接,
程序继续烧写,继而完成。
烧写完成,提示“上传成功”,
【7.1】然后,断开8266的EN、IO0和板子的连接。如果不再需要和Arduino进行串口通信,TX、RX针脚也可以断开。
【7.2】再次将EN和3.3V连接,模块就进入工作模式了。
来源:Arduino和ESP8266-模块安装及代码上传
简单点说就是;在编译快完成时拉低IOO然后,rst低-高-低重启模块进入下载模式。
OK,下面可以写各种程序happy了。
刷at固件,连接和烧写程序一样ESP8266: Reflash Dance!
/* This sketch demonstrates how to set up a simple HTTP-like server. The server will set a GPIO pin depending on the request http://server_ip/gpio/0 will set the GPIO2 low, http://server_ip/gpio/1 will set the GPIO2 high server_ip is the IP address of the ESP8266 module, will be printed to Serial when the module is connected. */ #include <ESP8266WiFi.h> const char* ssid = "401-2G"; const char* password = "415408807"; // Create an instance of the server // specify the port to listen on as an argument WiFiServer server(80); void setup() { Serial.begin(9600); delay(10); // prepare GPIO2 pinMode(LED_BUILTIN, OUTPUT);//在arduino里默认#define LED_BUILTIN 13,esp8266里默认为GIO2 digitalWrite(LED_BUILTIN, 0); // Connect to WiFi network Serial.println(); Serial.println(); Serial.print("Connecting to "); Serial.println(ssid); WiFi.begin(ssid, password); while (WiFi.status() != WL_CONNECTED) { delay(500); Serial.print("."); } Serial.println(""); Serial.println("WiFi connected"); // Start the server server.begin(); Serial.println("Server started"); // Print the IP address Serial.println(WiFi.localIP()); } void loop() { // Check if a client has connected WiFiClient client = server.available(); if (!client) { return; } // Wait until the client sends some data Serial.println("new client"); while (!client.available()) { delay(1); } // Read the first line of the request String req = client.readStringUntil('\r'); Serial.println(req); client.flush(); // Match the request int val; Serial.printf("%d\n", req.indexOf("/gpio/0")); //查找是否包含/gpio/0,找不到返回-1 Serial.printf("%d\n", req.indexOf("/gpio/1")); if (req.indexOf("/gpio/0") != -1) val = 0; else if (req.indexOf("/gpio/1") != -1) val = 1; else { Serial.println("invalid request"); client.stop(); return; } // Set GPIO2 according to the request digitalWrite(LED_BUILTIN, val); client.flush(); // Prepare the response // String s = "HTTP/1.1 200 OK\r\nContent-Type: text/html\r\n\r\n<!DOCTYPE HTML>\r\n<html>\r\nGPIO is now "; // s += (val) ? "high" : "low"; // s += "</html>\n"; // // Send the response to the client // client.print(s); client.print("<html><body><p>GPIO is now "); client.print((val) ? "high" : "low"); client.println(" </p>"); client.print("<a href=\"http://"); client.print(WiFi.localIP()); client.println("/gpio/1\">开</a>");//当遇到要输出"时,为了避免和print(""),可以写成print("\"") client.print("<a href=\"http://"); client.print(WiFi.localIP()); client.println("/gpio/0 \">关</a>"); client.println("</body></html>"); delay(1); Serial.println("Client disonnected"); // The client will actually be disconnected // when the function returns and 'client' object is detroyed }
Copyright © 2003-2013 www.wpsshop.cn 版权所有,并保留所有权利。